87 resultater (0,19547 sekunder)

Vis alle filtre

Mærke

Butik

Pris (EUR)

Vis alle

Nulstil filter

Produkter
Fra
Butikker

Microcontroller with sensors and accessories. Starter kit expansion for Arduino UNO R3

Microcontroller with sensors and accessories. Starter kit expansion for Arduino UNO R3

Starter kit expansion for Arduino learning on UNO R3. Set includes: 1x CD with instructions, 1x UNO R3, 1x High quality box, 1x USB cable, 1x jumper wire pack (65 wires), 6 Pin Dupont Line (male-female), 1x 400 tie point interlocking solderless breadboard, 1x extension plate, 1x 9V 1A EU Plug Adapter, 1x MPU 6050 gyroscope module, 1x HC-SR04 ultrasonic sensor , 1x UNL2003 Driver Board, 1x DC motor, 1x 5V 4-phase stepper motor, 1x Servo motor SG90 (9 g, 180°), 1x LCD1602 Blue Light module, 1x joystick module for PS2 games,1x relay module, 1x 9V battery clip, RGB module, 25x LED, (white, yellow, blue, red and green), 100x 10R/100R/220R/330R/1K/2K/5K1/10K/100K/1M resistors, 5x PN2222, BC547 and BC557 transistors,5x 1n4001 diode, 1x thermistor, 5x capacitor (22pf & 1 uf), 2x 50V capacitor (10uf) and 50V capacitor (100uf), 2x potentiometer (50k), 1x passive buzzer, 1x 74HC595N integrated circuit,1x MAX7219 module, 1x L293D integrated L293D circuit, 1xInfrared receiver module, 2x 5mm LDR, 5x push-button switch, 1x IR remote control pilot (battery not included), 1 digit seven-segment display, 1x 4 digit seven-segment display, 1x 8x8 dot matrix, 1 x US1881 TO-92 hall effect sensor.

DKK 832.50
1

Microcontroller with sensors and accessories. Atmega2560 - the most complete Arduino starter kit

Microcontroller with sensors and accessories. Atmega2560 - the most complete Arduino starter kit

Set includes: 25x LED, (white, yellow, blue, red and green), 1x RGB led, 10x ceramic capacitor (22 pf & 104 pf), 2x photoresistors, 1x thermistor, 5x rectifier diode (1N4007), 4x Electrolytic capacitor (10UF 50V & 100UF 50V), 10x NPN transistor (PN2222 & S8050), 1x tilt switch, 5x button (small), 1x 1 digit seven-segment display, 1x 4 digit seven-segment display, 1x sound sensor module, LCD1602 module (with pin header), 1x L293D integrated circuit, 74HC595 integrated circuit, 1x active buzzer, 1x passive buzzer, 1x RTC module, 1x DHT11 temperature and humidity sensor, 2x potentiometer, 1x rotary encoder module, 1x joystick module, 1x keyboard module, 1x 5V relay, 1x IR receiver module, 1x MEGA2560 controller board, 1 x prototype shield board, 1x Servo motor (SG90), 1x stepper motor, 1x stepper motor driver board ULN2003, 1x prototype extension board, 1x power module (warning: do not use voltage higher than 9V), 1x HC-SR501 pir motion sensor, 1x ultrasonic sensor, 1x GY-521 module (with pin header), 1x 3V servo motor, 1x MAX7219 module, remote control pilot (battery not included), 1x 9V power supply, 1x jumper wire pack (65 wires), 1x water level sensor, 1x USB cable, 1x RC522 RFID module, 120x 10R/100R/220R/330R/1K/2K/5K1/10K/100K/1M resistors, 20x female-male Dupont jumper cord.

DKK 1117.50
1

Small robot car

Small robot car

This kit was designed for those who would like to increase their practical and theoretical knowledge of the Arduino programming environment as well as robot building. You will be able to see with your own eyes how sensors, motor controllers and many other elements function, and you will learn how to build programmable devices. With the new skills, you make a multitasking robot that can avoid obstacles, identify the source of the strongest light and follow the commands sent to it via the remote control. Become a robotics master! Set of screws and nuts; Elements of the body; two wheels; Arduino UNO R69 RJ12; Remote controller; fan; screwdriver; clamping plates; insulating tape 5m x 18mm; Servo SG-90; USB cable; 2 x in-wheel motor; charger; mounting brackets; plastic third wheel; silicone battery extension cable; 5 x programming cable; battery cassette; 2 x joystick module; ultrasonic sensor; IR sensor; LED; touch module; power supply port; temperature sensor; buzzer module; DC servo motor; sound sensor; button; light sensor; traffic light module; laser LED; SMD RGB module; potentiometer; human pyrolysis sensor; plastic case; age: 12+

DKK 1030.00
1

Microcontroller with sensors and accessories. RFID set - complete starter kit for Arduino

Microcontroller with sensors and accessories. RFID set - complete starter kit for Arduino

Complete RFID starter kit, perfect for exercises in expanding the knowledge of programming. Set includes: 1x Components introduction documents, 1x UNO R3 board, 1x USB cable, 1x jumper wire pack (65 wires), 30x (220R, 10K, 1K) resistor, 1x 10 pin male-female Dupont jumper cord, 1x potentiometer, 1x active buzzer, 1x passive buzzer, 1x 74HC595N integrated circuit, 1x infrared receiver, 1x LM35DZ temperature sensor, 1x flame sensor, 2x ball switch, 3x 5mm LDR, 5x Tactile push button switch, 1x Infrared remote control, 1x 1 digit tube segment, 1x 4 digit tube segment, 1x 8x8 dot matrix, 1x stepper motor driver board UNL2003, 1x stepper motor, 1x Servo motor (SG90), 1x LCD1602 display with IIC/I2C modules, 1x Joystick module for PS2 games, 1x DHT11 temperature and humidity sensor , 1x water level sensor, 1x RFID module, 1x RFID keyring, 1x RFID card, 1x sound sensor module, 1x relay module, 1x RTC module, 1x matrix keypad module (16 buttons), 1x Three colour RGB module, 1x 9V battery clip.

DKK 897.50
1

Robot starter kit

Robot starter kit

An educational kit for beginners or advanced users who would like to start their adventure with Arduino programming. Thanks to the rich set of components compatible with open-source Arduino software, you can combine fun with learning. There are 17 worksheets with lists of components and circuit diagrams for each project included in the kit. Additionally, everything is kept in an aesthetic and practical plastic box that makes it easy to transport. Arduino Uno R3; prototype breadboard 400 connection points; prototyping shield; 30 male-male connector cables; 10 male-female connector cables; motion sensor PIR HC-SR501; ultrasonic distance sensor HC-SR04; temperature sensor LM35; battery cassette 6 x AA; IR remote controller; Fan motor 130; fan; 9G micro servo; 4 x buttons; 3 x potentiometer 10K; vibration sensor module; transmitter; infrared receiver; light sensor; 8-segment LED display; buzzer; 9 x 5mm LED; 1 x RGB LED; resistors 20 x 220R, 4,7K, 10K, 1K; 17 worksheets; plastic case; age: 8+

DKK 680.00
1

Microcontroller with sensors and accessories. The biggest starter kit for Arduino

Microcontroller with sensors and accessories. The biggest starter kit for Arduino

Set includes: 1x Double layer storage box (dim:. 23,4 x 16,8 x 6,2cm), 1x UNO R3, 1x 1.64ft USB cable (0.5m), 1x LCD1602 display module (can be soldered), 1x Servo motor SG90 (9 g, 180°), 1x 830 points breadboard (can be soldered), 1x ULN2003 Driver Board (green), 1x IR remote control pilot (battery not included), 1x 28BYJ-48 5v 4-stepper motor, 1x jumper wire pack (65 wires), DS3231 AT24C32 IIC Module (battery not included), 1x . MFRC-522 RC522 RFID + S50 + card + RFID keyring, 1x 4x4 Matrix, 1x keypad module (16 buttons), 1x joystick module for PS2 games, 1x 1-Channel 5V Relay Module, 1x sound sensor module, 1x DIP 3 Colour LED Module, 1x DHT11 temperature and humidity sensor, 1x rainwater level sensor module, 1x 0,56?, red, 4 digit seven-segment LED display (12 pin), 1 x LED Matrix red 8x8 64 LED 3mm CA, 1 x 9 Volt Battery Adapter. 1 x 10Pin Dupont wire (male, female), 1 x CD guide, 1 x SMD 3-coloured LED modules, 1 x 170 points Mini Breadboard SYB-170 White, 1 x 3 in 1 resistor kit, 1 x LED pack

DKK 855.00
1

Smart Robot Car Uno R3

Smart Robot Car Uno R3

Smart Robot Car Uno R3 is an intelligent robot used for educational purposes. The STEAM set was designed for beginners who are just starting their adventure with programming, electronics and robotics. Inside, there are 24 different modules, for example: obstacle avoidance, line tracing module, infrared remote control. The robot can be controlled via mobile devices with Android or IOS systems. Smart Robot Car Uno R3 is easy to assemble. A CD guide included in the set contains all necessary instructions on how to build the robot. The kit consists of: 1 x UNO R3, 1 x USB cable, 1 x V5.0 extension board, 1 x L298N motor driver board, 1 x ultrasonic Sensor, 1 x ultrasonic holder, 1 x servo motor, 1 x Bluetooth module, 1 x IR receiver module, 3 x line tracing module, 4 x motor, 1 x remote, 1 x charger, 1 x cell box, 2 x acrylics plates, 4 x wheels, 8 x screws, 38 x nuts, 4 x aluminium blocks, 6 x copper column, 6 x copper screws, 20 x Dupont wires, 1 x CD guide.

DKK 1470.00
1

Microcontroller with sensors and accessories. The most complete guide for Arduinu UNO R3

Microcontroller with sensors and accessories. The most complete guide for Arduinu UNO R3

Set includes: 25x LED, (white, yellow, blue, red and green), 1x RGB led, 10x ceramic capacitor (24 pf & 104 pf), 2x photoresistors, 1x thermistor, 5x rectifier diode (1N4007), 4x Electrolytic capacitor (10UF 50V & 100UF 50V),10x NPN transistor (PN2222 & S8050). 1x tilt switch, 5x button (small), 1x 1 digit seven-segment display, 1x 4 digit seven-segment display, 1x sound sensor module, 1x blue LCD1602 module, 1x integrated L293D circuit. 1x integrated 74HC595 circuit, 1x active buzzer, 1x passive buzzer, 1x RTC module, 1x DHT11 temperature and humidity sensor, 2x potentiometer, 1x rotary encoder module, 1x joystick module, 1x keyboard module, 1x 5V relay, 1x IR receiver module, 1x UNO R3 Controller Board, 1x breadboard, 1x Servo motor (SG90), 1x stepper motor, 1x stepper motor driver board ULN2003, 1x prototype extension board, 1x MB102 motherboard, 1x 3.3V-5V power supply module, 1x HC-SR501 PIR Motion Sensor Green, 1x Ultrasonic sensor, 1x GY-521 MUP6050 module, 1x 3v dc motor with cable, 1x MAX7219 module with cable, 1x remote control pilot (battery not included). 1x 9V 1A EU plug adapter, 1x jumper wire pack (65 wires), 1x rainwater level detector, 1x USB cable, 1x 9V DC battery, 1x RC522 RFID module, 120x 10R/100R/220R/330R/1K/2K/5K1/10K/100K/1M resistors, 20x female-male Dupont jumper cord.

DKK 920.00
1

Microcontroller with sensors and accessories. Set of 37 sensors and modules - Arduino Sensor Kit

Microcontroller with sensors and accessories. Set of 37 sensors and modules - Arduino Sensor Kit

Set includes: 1x high quality box, 1x modules introduction, 1x tutorial on CD,1x joystick module for PS2 games, 1x IR receiver module, 1x laser sensor module, 1x DHT11 temperature and humidity sensor,1X IR emitter sensor module, relay module (1 channel), 1x infrared obstacle avoidance sensor module , 1x touch sensor, 1x sound sensor, 1x DIP 3 Colour LED Module, 1x flame sensor module, 1x 3 Colour SMD LED Module, 1x Linear magnetic Hall sensor, 1x blue rotary encoder module, 1x digital temperature sensor, 1x active buzzer, 1x passive buzzer, 1 x photo interrupter module, 1x DS18B20 temperature sensor module, 1x 5mm bi-colour LED module, 1x tilt switch, 1x 7 coloured flash LED module, 1x photoresistor module, 1x vibration switch module,1x knock sensor module,1x TCRT5000 tracking module, 1x tactile switch module, 1x HC-SR04 ultrasonic sensor (4 pins), 1x GY-521 MPU6050 module (with soldering), 1x HC-SR501 PIR motion detector (green), 1x LCD1602 display (with soldering) ,1x DS3231 AT24C32 IIC module (battery not included), 1x MB102 3.3V 5V motherboard power supply module, 1x 4x4 membrane switch, 1x matrix keyboard, 1x water level sensor.

DKK 502.50
1

Weights for wrists and ankles

Weights for wrists and ankles

Universal weights intended for arm and leg exercises. They facilitate the formation of correct motor coordination, training proper motor skills and movement planning. The adjustable velcro strap makes the weights possible to fit to the chosen body part. They are made of durable denim and pleasant to touch Minky fabric, which makes the weights soft in contact with the skin. Quilted lining made of cotton is filled with metal beads. 2 pcs.: dim.: 25 x 8,5 cm; weight: 1 kg; material: grey denim, Minky fabric in grey, cotton; filling: metal beads; regulation: velcro strap;

DKK 395.00
1

toddlers? activity corners Track with slide

toddlers? activity corners Track with slide

Made of soft shapes joined with strong velcros, this corner guarantees long and safe play time in creches, nurseries and playrooms. It helps develop muscles, motor coordination and peer relations. It will also enrich motor rehabilitation rooms or sensory integration therapy rooms. For children?s safety, all the elements are made of non-slip fabric. 6 elements: 2 x matress ? 60 x 87.5 x 3 cm; small beam ? 60 x 25 x 15 cm; large beam ? 60 x 25 x 30 cm; bridge ? 60 x 60 x 30 cm; ramp ? 60 x 68 x 30 cm

DKK 5702.50
1