shatter me box set from GBP 20 | See the cheapest prices and offers on css.lazzaweb.dk

System Sensor Surface Mount Module Box SMB500

System Sensor Surface Mount Module Box SMB500The SMB500 surface mount box may be used with certain System Sensor modules when flush or recessed mounting are not possible.

GBP 38.56

1

System Sensor BS7273 Door Release System SSE-DRS-1

System Sensor BS7273 Door Release System SSE-DRS-1BS7273 Door Release system. Comprising DRM-1 door release module and M201 single output model prewired and mounted in SMB6-V0 surface mount box. Used provide a compliant solution to BS7273-4 Category A requirements. Powered from the 12-24v door magnet supply. System Sensor protocol.

GBP 215.50

1

System Sensor CR-6EA Six Way Changeover Relay Output

System Sensor CR-6EA Six Way Changeover Relay OutputCR-6EA contains 6 bi-stable NO NC relays. The first address is set from 01 to 154 and the remaining addresses are automatically assigned as the next five addresses. You can disable up to three unused addresses. Each address corresponds to one isolated relay contact set that can be connected as normally open or as normally closed. The module allows the Signalling Centre to control each relay separately on demand. The module has a built-in double-sided short circuit isolator.

GBP 468.86

1

System Sensor M220EA Dual Input or Monitor Module

System Sensor M220EA Dual Input or Monitor ModuleThe wired range of Input Output modules has been redesigned to address its microcontroller obsolescence and grant full backward-compatibility.The M220EA monitors one or two sets of normally open contacts and has two tri-colour LED indicators One for each channel. The fire panel can be configured to switch the relevant channel indicator on red in the event of an alarm on an input channel. The indicators can be set by panel command to pulse green each time the module channel is polled. The relevant indicator blinks yellow if the module detects an open-circuit on the input circuit.This module features automatic fault supervision and a built-in isolator on the analogue addressable circuit. The isolator may be bypassed.Two mounting holes and a pair of DIN rail clips allow the module to be installed in any type of enclosure including a purpose-built surface-mount box M200E-SMB. The indicator LEDs and address switches are accessible and visible in both DIN-rail and surface mount installations.Key FeaturesIndividually addressable by the fire panelInput circuits supervised for open-circuit faultsTri-colour indicator LEDs visible from front and one sideAutomatic detection of short-circuits on AA circuitAA circuit short-circuit isolatorOptional isolator bypassScrewdriver operated rotary address switches accessible from front and one sideClips for top hat 35 mm DIN railTwo mounting holesUp to 99 module addresses per AA circuit F220 F100AUses two addresses on the analogue addressable circuitPlease note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 86.75

1

System Sensor Recess Mounting Kit White RMK400AP

System Sensor Recess Mounting Kit White RMK400APRecess mounting kit suitable for flush mounting bases into a false ceiling. The System Sensor RMK400AP recessed mounting kit provides a simple installation solution where the application demands a lower profile sensor. The RMK400AP is for white sensors the RMK400AP-IV is for Ivory coloured sensors.Key FeaturesReduces the depth of any System Sensors sensor mounted in a standard 102mm diameter base by up to 20mm.Appropriate for drywall or suspended acoustical panel ceilings.May be used with standard junction boxes connected to flexible conduit.Incorporates special mounting bracket that secures the kit and base assembly to the junction box and ceiling panel.

GBP 19.82

1

System Sensor M201EA Output Control Module

System Sensor M201EA Output Control ModuleThe System Sensor M200 wired range of Input Output modules has been redesigned to address its microcontroller obsolescence and grant full backward-compatibility.The new M200 look and feel combine maximum reliability with top-end functionality. Their unique mechanical design allows each module to be mounted in either a common wall box on a DIN rail or its dedicated enclosure.Key FeaturesCommon mechanical platform for modules enclosureLow standby currentFACP reads module power voltageHigh Power Loop 48V readyBuilt-in short circuit isolatorsAddressability through rotary switchesTri-colour Light PipeImproved Light Pipe visibility on two sidesPlug-in field wiring terminalsIntegrated DIN rail bracketsLasered engraved label dataIP rate 30Intertek ApprovedPlease note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 68.16

1

System Sensor M210EA Single Input Monitor Module

System Sensor M210EA Single Input Monitor ModuleThe newly designed platform of M200 family of Input Output modules completes the S200AP line of wired spot detectors with unaltered family feeling and undisputed continuity.The new M200 look and feel combine maximum reliability with top-end functionality all enriched by a cutting-edge modern design.Single and multi-way models are available within the renewed mechanical package reducing both the cost of installation and the mounting space required.Their unique mechanical design allows each module to be mounted in either a common wall box on a DIN rail or its dedicated enclosure. The DIN rail mounting option is possible thanks to smart DIN brackets directly built-in the enclosure. Irrespective of the mounting methods chosen the address switch is always visible and accessible for selection.Each module has built-in short circuit protection for the communications loop however to increase application flexibility the isolators can be selecteddeselected on an individual module basis.To help technicians in the maintenance and fault-finding process light pipes have been enlarged to increase visibility even in the most challenging space constrained application. Both the status LED and the rotary switch selection can be viewed on the two sides without having to remove the cover of the surface mounting box. The multi-colour status LED provide diagnostic information regarding the status of each individual inputoutput.For ease of installation testing and maintenance modules have been equipped with quick connectors.The renovated aesthetics offers data finely engraved on the enclosures surface by laser for lifetime durability and resistance to degradation.Please note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 57.14

1

System Sensor M221EA Dual Input and Single Control Output Combination Module

System Sensor M221EA Dual Input and Single Control Output Combination ModuleThe System Sensor M200 wired range of Input Output modules has been redesigned to address its microcontroller obsolescence and grant full backward-compatibility.The new M200 look and feel combine maximum reliability with top-end functionality. Their unique mechanical design allows each module to be mounted in either a common wall box on a DIN rail or its dedicated enclosure.Key FeaturesCommon mechanical platform for modules enclosureLow standby currentFACP reads module power voltageHigh Power Loop 48V readyBuilt-in short circuit isolatorsAddressability through rotary switchesTri-colour Light PipeImproved Light Pipe visibility on two sidesPlug-in field wiring terminalsIntegrated DIN rail bracketsLasered engraved label dataIP rate 30Intertek ApprovedPlease note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 128.75

1

System Sensor M200XE Loop Isolation Module

System Sensor M200XE Loop Isolation ModuleThere is a large number of System Sensor intelligent fire alarm systems the address loop with a recipient device up to 198 is protected by a single one loop interruption but in the case of loop short circuit the entire loop it may become inoperable. With the M200XE modules shorting is not desired can be reduced.Only a small part of the system falls out if the loop is broken down into isolators because in the case of a possible loop only the two isolators will not be available to the control panel. If the address loop voltage drops below 7V the isolator module - with FET on the branch breaks it off the loop in the non-short-term part of the address loop the assets remain operational. If the breakdown the loop voltage rises on one side of the module then the separated short-circuit loop section 3 mA max. 15 mA control current flows through the module.In isolation the address loop wires between min. 2.2 kOhm resistance. The isolated state is maintained until the voltage of the disconnected section is 7V the short-circuit or the abnormally high current consumption ceases to exist. After the termination of the termination the isolator disengages the loop automatically.The two-colour LED on the module flashes green in the normal state of the loop every 3 seconds. If the module on any side it detects a short-circuit it illuminates with continuous yellow light during the shutter. The M200XE module in the M200E-SMB mounting box is wall-mounted with the M200E-DIN clip directly on the DIN rail M200E-PMB clip can be mounted in the fire panels box.

GBP 55.08

1

System Sensor M210E-B Single Input Monitor Module With M200E-SMB

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor M210E-B Single Input Monitor Module With M200E-SMBProvides single channel monitoring of normally open contact fire alarm and supervisory devices. The M210E has a single tri-colour greenredyellow LED which can be set by panel command to pulse green each time the module is polled. In case of an alarm the panel can switch the red indicator on continuously.The Yellow LED is controlled by the module and blinks to indicate an open circuit on the input circuit. This fault indication is overridden by a panel command to turn the red LED on.Key FeaturesComes withM200E-SMB for surface mounting

GBP 56.24

1

System Sensor M201E-B Output Control Module With M200E-SMB

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor M201E-B Output Control Module With M200E-SMBThe M201E provides a single output that can be switched when commanded by a fire alarm control panel. In the supervised mode the M201E supervises the wiring to the load devices. Upon command from the fire alarm control panel the M201E switches an external power supply to operate these devices while de-activating the load supervision.The module raises an unlatched fault condition if the external power supply voltage falls below the fixed threshold. In the unsupervised mode the M201E provides one set of form C changeover contacts and does not provide load nor power supply supervision. The M201E has built-in short circuit protection for the communications loop which may be selecteddeselected to meet the specific requirements of each installation.Key FeaturesComes withM200E-SMBfor surface mounting

GBP 58.97

1

System Sensor WSF-RR-RF Wall Mounted Addressable Wireless VAD - RedRed

System Sensor WSF-RR-RF Wall Mounted Addressable Wireless VAD - RedRedThe Agile Wireless Sounder Strobe forms part of the Agile range of products that cover a wide range of applications where wiring is undesired.The Agile Wireless Fire Detection System is a newly designed platform of wireless fire devices suitable for all applications where wired fire devices cannot be installed for economic or aesthetic reasons. The new wireless platform is powered by robust MESH network technology providing REDUNDANT communication paths to each wireless device. This makes the network highly reliable protecting against broken communication links. All operations for the design configuration and diagnostics of the systems are greatly simplified thanks to the AgileIQ software suite specifically designed to support AGILE throughout the whole lifecycle of the product.Key FeaturesMesh multiple communication paths for increased reliabilityEN54-23 VAD approvedLight coverage W-3.5-1005 Hz Red Flashing VAD with up to 350mc of coverageConsistent sound performance like wired sounder 100dBA max SPL32 user selectable tones through Agile IQDynamic tone selection through Advanced protocol commandsIP21 protection from water and dust entrance18RF channels at 868MHz provides greater tolerance to interference2 integrated antennas on each wireless fire device easier positioning of devicesUp to 400 m free air communication range providing good coverage levelsAverage 5 year battery service life reducing maintenance requirementsAddresses set using rotary switches reduced commissioning timeTamper-resist locking mechanism to prevent unauthorised removal of device from its baseWired fire devices look and feel easier installation and visual integrationPatented battery service life prediction feature more proactive maintenancePeace of mind battery redundancy delivering always on performanceUp to 32 Wireless devices per GatewayAgile IQ 3-in-1 software for easy design configuration and diagnostics

GBP 297.43

1

System Sensor WSF-WR-RF Wall Mounted Addressable Wireless VAD - WhiteRed

System Sensor WSF-WR-RF Wall Mounted Addressable Wireless VAD - WhiteRedThe Agile Wireless Sounder Strobe forms part of the Agile range of products that cover a wide range of applications where wiring is undesired.The Agile Wireless Fire Detection System is a newly designed platform of wireless fire devices suitable for all applications where wired fire devices cannot be installed for economic or aesthetic reasons. The new wireless platform is powered by robust MESH network technology providing REDUNDANT communication paths to each wireless device. This makes the network highly reliable protecting against broken communication links. All operations for the design configuration and diagnostics of the systems are greatly simplified thanks to the AgileIQ software suite specifically designed to support AGILE throughout the whole lifecycle of the product.Key FeaturesMesh multiple communication paths for increased reliabilityEN54-23 VAD approvedLight coverage W-3.5-1005 Hz Red Flashing VAD with up to 350mc of coverageConsistent sound performance like wired sounder 100dBA max SPL32 user selectable tones through Agile IQDynamic tone selection through Advanced protocol commandsIP21 protection from water and dust entrance18RF channels at 868MHz provides greater tolerance to interference2 integrated antennas on each wireless fire device easier positioning of devicesUp to 400 m free air communication range providing good coverage levelsAverage 5 year battery service life reducing maintenance requirementsAddresses set using rotary switches reduced commissioning timeTamper-resist locking mechanism to prevent unauthorised removal of device from its baseWired fire devices look and feel easier installation and visual integrationPatented battery service life prediction feature more proactive maintenancePeace of mind battery redundancy delivering always on performanceUp to 32 Wireless devices per GatewayAgile IQ 3-in-1 software for easy design configuration and diagnostics