the way of the superior man from GBP 21 | See the cheapest prices and offers on css.lazzaweb.dk

System Sensor MCX-55ME 5-Way Input amp 5-Way Output Card

System Sensor MCX-55ME 5-Way Input 5-Way Output CardModule with 5 inputs and 5 outputs. Each input can be connected on a monitored line to two or four conductors. Each output has a potential-free changeover contact. Compatible with both CLIP and Advanced control panels. The module uses 10 consecutive addresses of the 99 available per line addresses programmable via dip-switch. Unused inputs or outputs can be excluded. CPR Certificate in compliance to EN 54-18.

GBP 611.39

1

System Sensor CR-6EA Six Way Changeover Relay Output

System Sensor CR-6EA Six Way Changeover Relay OutputCR-6EA contains 6 bi-stable NO NC relays. The first address is set from 01 to 154 and the remaining addresses are automatically assigned as the next five addresses. You can disable up to three unused addresses. Each address corresponds to one isolated relay contact set that can be connected as normally open or as normally closed. The module allows the Signalling Centre to control each relay separately on demand. The module has a built-in double-sided short circuit isolator.

GBP 468.86

1

System Sensor MMX-10ME 10-Way Monitor Input Card

System Sensor MMX-10ME 10-Way Monitor Input CardThe MMX-10ME is a multi-module card that groups 10 monitored inputs. This is a space-saving and economical solution when many input modules are needed. Each input module has an LED LED output and micro switch with which each module can be switched off individually. The connectors can be plugged in for easy connection. The MMX-10ME multi-module card conforms to the European CPD guidelines.

GBP 517.07

1

System Sensor CMX-10RME 10-Way Relay Control Output Card

System Sensor CMX-10RME 10-Way Relay Control Output CardThe CMX-10RME is a multi-module card that groups 10 relay outputs. This is a space-saving and economical solution when many exits are needed. Each relay output 30VDC-1A has an LED LED output and microswitch with which each module can be switched off individually. The connectors can be plugged in for easy connection. The CMX-10RME multi-module card conforms to European CPD guidelines.

GBP 593.48

1

System Sensor 52051RE-26 Rate of Rise 58C Heat Detector

System Sensor 52051RE-26 Rate of Rise 58C Heat DetectorThe 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 53.02

1

System Sensor Agile Rate of Rise Heat Detector 52051RE-RF

System Sensor Agile Rate of Rise Heat Detector 52051RE-RFThese heat sensors are battery operated RF devices designed for use with the M200G-RF radio gateway. They contain a wireless transceiver and run on an addressable fire system using a compatible proprietary communication protocol. The 52051E-RF provides fixed 58oC temperature sensing A1S. The 52051RE-RF provides 58oC rate-of-rise 10oCminute temperature sensing A1R. The sensors plug into the B501RF wireless base. These devices conform to EN54-25 and EN54-5 classes A1S and A1R. They comply with the requirements of 201453EU for conformance with the RED directive.

GBP 185.89

1

Notifier ECO1005A ECO Rate of Rise Temperature Detector

Notifier ECO1005A ECO Rate of Rise Temperature DetectorThe ECO1005 A thermal detector belongs to System Sensors ECO1000 range of detectors. ECO1000 is a range of conventional detectors which have been produced using the latest in manufacturing technology and supplied with an array of advanced features making them better by design.The ECO1005 A thermal detector uses a state of the art thermal element combined with an application specific integrated circuit ASIC to provide quick and accurate detection of fires. The detector incorporates both rate of rise and static elements and is suitable for all areas where the ambient conditions do not normally exhibit rapid changes in temperature.Key FeaturesLow profile designLow current draw58C operating temperatureOperates at 12 and 24VDCRemote alarm test featureEasy MaintenanceApproved to EN54 52000 Class A1RApproved to MED 9698EC Amendment 200926ECExtended warranty

GBP 21.01

1

System Sensor Wireless Remote Indicator Pack of two units M200I-RF

System Sensor Wireless Remote Indicator Pack of two units M200I-RFThe System Sensor M200I-RF is a wireless remote indicator unit for use with the Agile range of wireless fire system equipment.

GBP 207.24

1

System Sensor CUPHWKIT Cup for Setup and Maintenance of Agile Wireless Detectors

System Sensor CUPHWKIT Cup for Setup and Maintenance of Agile Wireless DetectorsThis product is ideal for assisting with the setup and maintenance of System Sensor Agile range of wireless fire alarm system detectors. They are designed for use with telescopic pole POLE HWKIT.

GBP 224.45

1

System Sensor IBS-LIDPW Pure White Base Cover Plate Pack of 10

System Sensor IBS-LIDPW Pure White Base Cover Plate Pack of 10The IBS-LIDPW is a pack of 10 pure white cover plates for use with the Notifier Sounder Bases Beacon Bases and Sounder Beacon Bases.

GBP 39.94

1

System Sensor M210EA Single Input Monitor Module

System Sensor M210EA Single Input Monitor ModuleThe newly designed platform of M200 family of Input Output modules completes the S200AP line of wired spot detectors with unaltered family feeling and undisputed continuity.The new M200 look and feel combine maximum reliability with top-end functionality all enriched by a cutting-edge modern design.Single and multi-way models are available within the renewed mechanical package reducing both the cost of installation and the mounting space required.Their unique mechanical design allows each module to be mounted in either a common wall box on a DIN rail or its dedicated enclosure. The DIN rail mounting option is possible thanks to smart DIN brackets directly built-in the enclosure. Irrespective of the mounting methods chosen the address switch is always visible and accessible for selection.Each module has built-in short circuit protection for the communications loop however to increase application flexibility the isolators can be selecteddeselected on an individual module basis.To help technicians in the maintenance and fault-finding process light pipes have been enlarged to increase visibility even in the most challenging space constrained application. Both the status LED and the rotary switch selection can be viewed on the two sides without having to remove the cover of the surface mounting box. The multi-colour status LED provide diagnostic information regarding the status of each individual inputoutput.For ease of installation testing and maintenance modules have been equipped with quick connectors.The renovated aesthetics offers data finely engraved on the enclosures surface by laser for lifetime durability and resistance to degradation.Please note This product requires the M200E-SMB for surface mounting or M200E-DIN for mounting to DIN rails.

GBP 57.14

1

System Sensor M200XE Loop Isolation Module

System Sensor M200XE Loop Isolation ModuleThere is a large number of System Sensor intelligent fire alarm systems the address loop with a recipient device up to 198 is protected by a single one loop interruption but in the case of loop short circuit the entire loop it may become inoperable. With the M200XE modules shorting is not desired can be reduced.Only a small part of the system falls out if the loop is broken down into isolators because in the case of a possible loop only the two isolators will not be available to the control panel. If the address loop voltage drops below 7V the isolator module - with FET on the branch breaks it off the loop in the non-short-term part of the address loop the assets remain operational. If the breakdown the loop voltage rises on one side of the module then the separated short-circuit loop section 3 mA max. 15 mA control current flows through the module.In isolation the address loop wires between min. 2.2 kOhm resistance. The isolated state is maintained until the voltage of the disconnected section is 7V the short-circuit or the abnormally high current consumption ceases to exist. After the termination of the termination the isolator disengages the loop automatically.The two-colour LED on the module flashes green in the normal state of the loop every 3 seconds. If the module on any side it detects a short-circuit it illuminates with continuous yellow light during the shutter. The M200XE module in the M200E-SMB mounting box is wall-mounted with the M200E-DIN clip directly on the DIN rail M200E-PMB clip can be mounted in the fire panels box.

GBP 55.08

1

System Sensor 52051E-26-B Fixed 58C Heat Detector With Base

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor 52051E-26-B Fixed 58C Heat Detector With BaseThe 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes B501AP baseIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector - included

GBP 30.84

1

System Sensor 52051EI-26 Fixed 58C Heat Detector with Isolator

System Sensor 52051EI-26 Fixed 58C Heat Detector with IsolatorThe 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 60.59

1

System Sensor 52051HTE-26 High Temperature Fixed 78C Heat Detector

System Sensor 52051HTE-26 High Temperature Fixed 78C Heat DetectorThe 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 53.02

1

System Sensor 52051E-26 Fixed 58C Heat Detector

System Sensor 52051E-26 Fixed 58C Heat DetectorThe 52051E and 52051HTE are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology for fast response and linear temperature sensing. Their linear response allows these sensors to be used to signal temperatures over the range of 58 degrees class A1S to 78 degrees Class BS.The 52051RE uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10 degreeminute typical or if the temperature exceeds a threshold of 58 degrees. With the implementation of the Series 200 Advanced Protocol any model can be software configures to be wither a fixed 58 degree a fixed 78 degree unit or a 58 degree with rate of rise device. For backwards compatibility and approval continuity three separate versions continue to be available as separate part numbers.The sensing elements of all three heat sensors are panel controllable through the Series 200 Advanced Protocol so the sensitivity threshold of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesIncludes Series 200 Advanced Protocol and the ability to customise the heat threshold of each detector to the specific risks found in the applicationAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 45.38

1

System Sensor M5A-RP01FF-K013-01 Flexible Manual Call Point

System Sensor M5A-RP01FF-K013-01 Flexible Manual Call PointInstallation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP Indoor Call Point range. Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.All MCP Indoor Call Point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going in to alarm. Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard compliant markings only. The MCP5A product has the Advanced Protocol embedded.Key FeaturesUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aesthetics and compact designFully approved to the latest standardsBackward compatibilityCPD Approved

GBP 50.26

1

System Sensor M5A-RP01FG-K013-01 Glass Manual Call Point

System Sensor M5A-RP01FG-K013-01 Glass Manual Call PointAddressable installation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP Indoor Call Point range. Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.All MCP Indoor Call Point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going in to alarm. Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard compliant markings only. The MCP5A product has the Advanced Protocol embedded.Key FeaturesUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aesthetics and compact designFully approved to the latest standardsBackward compatibilityCPD Approved

GBP 48.89

1

System Sensor M5A-RP02FG-K013-01 Glass Manual Call Point with Isolator

System Sensor M5A-RP02FG-K013-01 Glass Manual Call Point with IsolatorInstallation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP Indoor Call Point range. Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.All MCP Indoor Call Point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going in to alarm. Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard compliant markings only. The MCP5A product has the Advanced Protocol embedded.Key FeaturesUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aesthetics and compact designFully approved to the latest standardsBackward compatibilityCPD Approved

GBP 61.27

1

System Sensor M5A-RP02FF-K013-01 Flexible Manual Call Point with Isolator

System Sensor M5A-RP02FF-K013-01 Flexible Manual Call Point with IsolatorInstallation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP Indoor Call Point range. Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.All MCP Indoor Call Point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going in to alarm. Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard compliant markings only. The MCP5A product has the Advanced Protocol embedded.Key FeaturesUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aesthetics and compact designFully approved to the latest standardsBackward compatibilityCPD Approved

GBP 61.27

1

System Sensor Agile Wireless Photo-Thermal-IR Detector 22051TLE-RF-26

System Sensor Agile Wireless Photo-Thermal-IR Detector 22051TLE-RF-26The 22051TLE multi-criteria multi-sensor Photo Thermal Infra-Red detector PTIR is the environmentally friendly alternative to the ionisation detector a technology that is over sixty years old. The detector offers comparable speed of response to the ionisations technology for a fast flaming fire and is less susceptible to false alarms. It can be deployed with confidence in locations where the main risk is from fast-developing flaming fires.The integration of continual monitoring for all three major elements of a fire enables the 22051TLE respond far more quickly to an actual fire and has the highest immunity to nuisance. The sensing elements of the 22051TLE are panel controllable so the sensitivity thresholds of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting. Agile wireless optical thermal and IR detector for use with the System Sensor Agile wireless system.Key FeaturesUnique true three sensor multi-criteria fire detector incorporating photoelectric thermal and IR sensing elementsFully integrated Infra-Red sensing to support the fire alarm decisionIncludes Series 200 Advanced ProtocolRotary decade address switchesPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibility

GBP 232.72

1

System Sensor 22051TLE-26 Photoelectric Thermal amp Infrared Detector

System Sensor 22051TLE-26 Photoelectric Thermal Infrared DetectorThe 22051TLE multi-criteria multi-sensor Photo Thermal Infra-Red detector PTIR is the environmentally friendly alternative to the ionisation detector a technology that is over sixty years old. The detector offers comparable speed of response to the ionisations technology for a fast flaming fire and is less susceptible to false alarms. It can be deployed with confidence in locations where the main risk is from fast-developing flaming fires.The integration of continual monitoring for all three major elements of a fire enables the 22051TLE respond far more quickly to an actual fire and has the highest immunity to nuisance. The sensing elements of the 22051TLE are panel controllable so the sensitivity thresholds of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesUnique true three sensor multi-criteria fire detector incorporating photoelectric thermal and IR sensing elementsFully integrated Infra-Red sensing to support the fire alarm decisionIncludes Series 200 Advanced ProtocolAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchesPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 77.11

1

System Sensor 22051TLE-26 Photoelectric Thermal amp Infrared Detector with Isolator

System Sensor 22051TLE-26 Photoelectric Thermal Infrared Detector with IsolatorThe 22051TLE multi-criteria multi-sensor Photo Thermal Infra-Red detector PTIR is the environmentally friendly alternative to the ionisation detector a technology that is over sixty years old. The detector offers comparable speed of response to the ionisations technology for a fast flaming fire and is less susceptible to false alarms. It can be deployed with confidence in locations where the main risk is from fast-developing flaming fires.The integration of continual monitoring for all three major elements of a fire enables the 22051TLE respond far more quickly to an actual fire and has the highest immunity to nuisance. The sensing elements of the 22051TLE are panel controllable so the sensitivity thresholds of each element can be changed by the panel offering the ability to customise the device for the changing use of the area it is protecting.Key FeaturesUnique true three sensor multi-criteria fire detector incorporating photoelectric thermal and IR sensing elementsFully integrated Infra-Red sensing to support the fire alarm decisionIncludes Series 200 Advanced ProtocolAvailable with or without single pole short circuit isolation with status control through the Series 200 Advanced ProtocolTri colour LED offering red green and amber coloursRotary decade address switchesPure white colour to compliment modern buildings100 mechanical and electrical backwards compatibilityNew base design to compliment the detector

GBP 92.95

1

System Sensor M201E-B Output Control Module With M200E-SMB

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor M201E-B Output Control Module With M200E-SMBThe M201E provides a single output that can be switched when commanded by a fire alarm control panel. In the supervised mode the M201E supervises the wiring to the load devices. Upon command from the fire alarm control panel the M201E switches an external power supply to operate these devices while de-activating the load supervision.The module raises an unlatched fault condition if the external power supply voltage falls below the fixed threshold. In the unsupervised mode the M201E provides one set of form C changeover contacts and does not provide load nor power supply supervision. The M201E has built-in short circuit protection for the communications loop which may be selecteddeselected to meet the specific requirements of each installation.Key FeaturesComes withM200E-SMBfor surface mounting

GBP 58.97

1

System Sensor M210E-B Single Input Monitor Module With M200E-SMB

Please note The price of this product including the base is a special promotional project offer directly from the manufacturer.System Sensor M210E-B Single Input Monitor Module With M200E-SMBProvides single channel monitoring of normally open contact fire alarm and supervisory devices. The M210E has a single tri-colour greenredyellow LED which can be set by panel command to pulse green each time the module is polled. In case of an alarm the panel can switch the red indicator on continuously.The Yellow LED is controlled by the module and blinks to indicate an open circuit on the input circuit. This fault indication is overridden by a panel command to turn the red LED on.Key FeaturesComes withM200E-SMB for surface mounting

GBP 56.24

1

Awardvindende Google Marketing Powerhouse

Brand

Merchant

Price (EUR)