ex nihilo blue talisman from GBP 47 | See the cheapest prices and offers on css.lazzaweb.dk

Apollo Exd Conventional Triple IR Flame Detector 55000-062APO

Apollo Exd Conventional Triple IR Flame Detector 55000-062APOThe Flameproof IR3 Flame Detector is designed for use in hazardous environments in indoor and outdoor applications.It is sensitive to low-frequency flickering infra-red radiation emitted by flames during combustion. The sensor operates even through a layer of oil dust water vapour or ice. Baseefa has certified the detector for compliance to standards EN 60079-0 EN 60079-1 and EN 61241-1 Key Features ATEX IECEx certified II2GD Ex d IIC T4 Gb Ex tb IIICT135 C Db IP66 A21 Zones 1 21 2 and 22Selectable output options Conventional two-wire 4-20mA Latching or Non-latching Relay Contacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP66 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55C

GBP 2340.00

1

Apollo Intelligent Blue Manual Call Point - SA5900-905APO

Apollo Intelligent Blue Manual Call Point - SA5900-905APOThe Intelligent Manual Call Point has been designed for indoor applications and are available in a variety of colours for different applications such as initiating a hazard rather than a fire alarm. The Intelligent Manual Call Point can be used on XP95 Discovery and CoreProtocol systems.A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.OperationThe address of each call point is set at the commissioning stage by means of a DIL switch. A solid red alarm LED is provided on the manual call point. This LED is controlled independently of the call point by the control panel. The LED will flash yellow if there is a fault and flash green when the device is polled. Discovery and CoreProtocol configurable. Once activated the Intelligent Manual Call Point can be reset by inserting the reset key into the front facing LED turning clockwise until a positive click and reset occurs.Key FeaturesResettable operating elementEasy access front reset mechanismE-Z fit connector system for installationErgonomic reset key170 viewableLED Continuity link for cable insulation testingSuitable for semi flush or surface mounting

GBP 46.91

1

Apollo I.S. Conventional Triple IR Flame Detector 55000-063APO

Apollo I.S. Conventional Triple IR Flame Detector 55000-063APOThe IS IR3 Flame Detector is designed for harsh environments in either indoor or outdoor applications. It is sensitive to low frequency flickering IR radiation emitted from flames during combustion.The sensor operates even through a layer of oil dust water vapour or ice. These detectors have been approved byBaseefa to standards EN50014 EN50020 and EN50284. The requirements of Directive 949EC the Atmosphere Explosives ATEX directive have also been met.Key Features ATEX IECEx certified II 1 GCENELECIEC Certified Ga Ex ia IIC T4Selectable output options Conventional two-wire 4-20mA Latching or Non-latching RelayContacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP65 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 40C T4Operating temperature -10C to 55C

GBP 2233.04

1

Apollo Exd Conventional Dual IR Flame Detector 55000-061APO

Apollo Exd Conventional Dual IR Flame Detector 55000-061APOThe Flameproof IR2 Flame Detector is designed for use in hazardous environments in indoor applications. The combination of filters and signal processing allows the sensor to be used with a very low risk of false alarms in difficult situations characterised by factors such as flickering lights. Baseefa has certified the detector for compliance to standards EN 60079-0 EN 60079-1 and EN 61241-1 Key Features ATEX IECEx certified II2GD Ex d IIC T4 Gb EE tb IIICT135 C Db IP66 A21 Zones 1 21 2 and 22Selectable output options Conventional two-wire 4-20mA Latching or Non-latching Relay Contacts - FireFault Pre alarmClass 1 sensitivity to EN54-10 detects 0.1m2 fire at 25mHigh optical interference immunitySelectable response speedOptical self-testLow power consumptionIP66 ratedSupply voltage 14 to 30VdcOperating temperature -10C to 55C

GBP 2129.40

1

Apollo Marine Series 65 Mounted UV Flame Detector 55000-026MAR

Apollo Marine Series 65 Mounted UV Flame Detector 55000-026MARThe Marine Series 65 Base Mounted UV Flame Detector is designed to protect enclosed indoor areas where open flaming fires may be expected. The detector has a fast acting response to flames up to 25m away and is equipped with a single UV sensor with a narrow spectral response in order to discriminate between flames and most spurious sources of radiation.OperationThe detector is sensitive to ultraviolet radiation emitted by flames during combustion. Since it requires only UV radiation the Flame Detector responds even to stationary flames with no flicker like cigarette lighters and blue gas flames. The detector is set to respond to ultraviolet radiation 185 to 260nm emitted by almost all flames including those invisible to the naked eye e.g. hydrogen fires.The detector has a single UV sensor with a narrow spectral response in order to discriminate between flames and most spurious sources of radiation and is designed for internal fully enclosed areas. Caution The detector will also detect electrical discharges from lightning or arc welding.Key FeaturesResponds to stationary flames with no flickerSensitive to UV radiation emitted by flames during combustionCompact flame detector which fits into 45681-200MAR baseZone-powered

GBP 920.40

1

Apollo Marine Intelligent Base Mounted UV Flame Detector 55000-027MAR

Apollo Marine Intelligent Base Mounted UV Flame Detector 55000-027MARThe Marine Intelligent Base Mounted UV Flame Detector is designed to protect enclosed indoor areas where open fires may be expected. The detector has a fast-acting response to flames up to 25m away and is equipped with a single UV sensor with a narrow spectral response in order to discriminate between flames and most spurious sources of radiation.ApplicationUV flame detectors are used when detection is required to be unaffected by convection currents draughts or wind. These include engine rooms in ships factories affected by draughts or wind and warehouses. They are fast reacting and respond to a flame more than 25m away. The UV flame detector is affected by arc welding electrical sparks lightning nuclear radiation and UV light sources. For applications where these phenomena are present a UV flame detector should not be used.OperationThe detector is sensitive to ultraviolet radiation emitted by flames during combustion. Since it requires only UV radiation the detector responds even to stationary flames with no flicker like cigarette lighters and blue gas flames.The detector is set to respond to ultraviolet radiation 185260nm emitted by almost all flames including those invisible to the naked eye e.g. hydrogen fires. The detector has a single UV sensor with a narrow spectral response in order to discriminate between flames and most spurious sources of radiation and is designed for internal fully enclosed areas. Caution The detector will also detect electrical discharges from lightning or arc welding.Key FeaturesResponds to stationary flames with no flickerSensitive to UV radiation emitted by flames during combustionCompact flame detector which fits into Discovery Marine baseLoop-powered

GBP 982.80

1

Awardvindende Google Marketing Powerhouse

Brand

Merchant