353 results (0,13489 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Apollo Isolator XP95 and Discovery 55000-720APO

Apollo Isolator XP95 and Discovery 55000-720APO

Apollo Isolator XP95 and Discovery 55000-720APOThe Isolator is placed at intervals on the loop and ensures that in the case of a short circuit only the section between the isolators will be affected. When the short circuit is removed the isolators automatically restore power and data to the isolated section.Key Features Detects wiring short-circuitsMinimises disruption from short-circuitsAutomatic de-isolation on the short-circuit removalUp to 20 detectors or their equivalent load may be installed between isolators

GBP 18.46
1

Apollo SA5100-810APO Soteria Tri-Sensor Detector Dual OpticalHeatCO

Apollo SA5100-810APO Soteria Tri-Sensor Detector Dual OpticalHeatCO

Apollo SA5100-810APO Soteria Tri-Sensor Detector Dual OpticalHeatCOThe Soteria Tri-Sensor Detector Dual OpticalHeatCO uses advanced dual optical sensing technology to accurately detect smoke particles and discriminate against false alarm stimuli. It has a centrally located heat thermistor along with a CO sensor giving you three methods of detection.The detector can operate in 5 modes of sensitivity.Soteria detectors have been designed to operate on Discovery loops. This allows for Soteria detectors and bases to operate on existing systems and for Soteria detectors to operate on Discovery bases XPERT 7 Intelligent Mounting Base.Key FeaturesAvailable with integrated switchable isolatorDrift compensationTricoloured LED status indicatorFasTest for quicker testing of detectorsLocking mechanism grub screwDIL Switch Addressing

GBP 67.08
1

Apollo Universal Bracket for Beam Detector Heads and Prisms 29600-527

Apollo Universal Bracket for Beam Detector Heads and Prisms 29600-527

Apollo Universal Bracket for Beam Detector Heads and Prisms 29600-527Universal Bracket for the Auto-Aligning Beam Detector.Auto-Aligning Beam Detector DescriptionThe high-performance Auto-Aligning Beam Detector comprises of a ground level controller detector head with auto-aligning feature integral laser for rapid initial alignment and single prism. An additional detector head can be added to the controller.Brand InformationAuto-compensates for building movement and contaminationIntegral laser and auto-align enable quicker installationLow-level system controller with LCD display and user-friendly interface

GBP 164.20
1

Apollo XPander Optical Smoke Detector and Mounting Base XPA-CB-12034-APO

Apollo XPander Optical Smoke Detector and Mounting Base XPA-CB-12034-APO

Apollo XPander Optical Smoke Detector and Mounting Base XPA-CB-12034-APOThe XPander Optical Smoke Detector works on the light scatter principle and is ideal for applications where slow-burning or smouldering fires are likely.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessPerforms well in black and white smokeBi-directional radio communicationsXPERT card addressing systemFiveyear battery life using standard AA alkaline batteries

GBP 185.70
1

Apollo XPander Sounder Beacon and A1R Heat Detector XPA-CB-14021-APO

Apollo XPander Sounder Beacon and A1R Heat Detector XPA-CB-14021-APO

Apollo XPander Sounder Beacon and A1R Heat DetectorXPA-CB-14021-APOXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch. Individual parts may be ordered separately.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectorsremote test facility3-5 years battery life

GBP 372.43
1

Apollo XPander Sounder Beacon and CS Heat Detector XPA-CB-14022-APO

Apollo XPander Sounder Beacon and CS Heat Detector XPA-CB-14022-APO

Apollo XPander Sounder Beacon and CS Heat DetectorXPA-CB-14022-APOXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch. Individual parts may be ordered separately.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectorsremote test facility3-5 years battery life

GBP 372.43
1

Apollo XPander Sounder Beacon and Optical Smoke Detector XPA-CB-14020-APO

Apollo XPander Sounder Beacon and Optical Smoke Detector XPA-CB-14020-APO

Apollo XPander Sounder Beacon and Optical Smoke DetectorXPA-CB-14020-APOXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch. Individual parts may be ordered separately.Key Featuresmodern stylingloop-powered interface operating on 868MHzwireless addresses seen by control panel as normal addressesradio base with wireless circuitry and battery compartmentchamber designed to inhibit dirt penetration and thus reduce false alarmsautomatic drift compensation with DirtAlert warningalgorithms for transient alarm rejectionFasTest reduces time taken to test detectors remote test facility3-5 years battery life

GBP 370.69
1

Apollo XPander Multisensor Detector and Mounting Base XPA-CB-13032-APO

Apollo XPander Multisensor Detector and Mounting Base XPA-CB-13032-APO

Apollo XPander Multisensor Detector and Mounting Base XPA-CB-13032-APOThe XPander Multisensor Detector contains an optical smoke sensor and a thermistor temperature sensor from which outputs are combined to give the final analogue value.Key Features WirelessMultisensor technology reduces false alarmsIncreased sensitivity to flaming firesXPERT card addressing systemFiveyear battery life using standard AA alkaline batteries

GBP 190.46
1

Apollo XPander A1R Heat Detector and Mounting Base - XPA-CB-11170-APO

Apollo XPander A1R Heat Detector and Mounting Base - XPA-CB-11170-APO

Apollo XPander A1R Heat Detector and Mounting Base - XPA-CB-11170-APOThere are two heat detectors in the XPander range designed to suit a wide variety of operating conditions. A static heat detector CS responds only when a fixed temperature has been reached and a Rate-of-Rise Detector A1R which has a fixed upper limit but in addition measures the rate of increase in temperature.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessCan be used in applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under natural conditionsCS detectors are ideal for use in the environments with rapid temperature fluctuations such as boiler roomsBi-directional monitored radio platformFiveyear battery life using standard AA alkaline batteries

GBP 188.28
1

Apollo XPander CS Heat Detector and Mounting Base - XPA-CB-11171-APO

Apollo XPander CS Heat Detector and Mounting Base - XPA-CB-11171-APO

Apollo XPander CS Heat Detector and Mounting Base - XPA-CB-11171-APOThere are two heat detectors in the XPander range designed to suit a wide variety of operating conditions. A static heat detector CS responds only when a fixed temperature has been reached and a Rate-of-Rise Detector A1R which has a fixed upper limit but in addition measures the rate of increase in temperature.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves. The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface.The detectors incorporate drift compensation and report any compensation limit occurring. The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key Features WirelessCan be used in applications where smoke detectors are unsuitableIdeal for environments that are dirty or smoky under natural conditionsCS detectors are ideal for use in the environments with rapid temperature fluctuations such as boiler roomsBi-directional monitored radio platformFiveyear battery life using standard AA alkaline batteries

GBP 187.36
1

Apollo XPander Sounder Visual Indicator Clear and Optical Smoke Detector XPA-CB-14024-APO

Apollo XPander Sounder Visual Indicator Clear and Optical Smoke Detector XPA-CB-14024-APO

Apollo XPander Sounder Visual Indicator Clear and Optical Smoke Detector XPA-CB-14024-APOThe XPander Sounder and Sounder Base is wireless and designed to be used with XPander detectors and manual call points.OperationXPander sounders can be wall or ceiling mounted and use a bi-directional monitored radio platform to communicate. They feature 32 selectable tones including the Apollo tone and a self-test which causes a fault signal to be sent if the sounders fail to operate. The self-test feature is activated by a DIL Switch.Brand InformationXPander incorporates entirely new designs with respect to the wireless communication system. A Radio Interface is connected to the loop. It communicates with the control panel using the Apollo addressable two-wire power and communications system. The interface communicates with the detection and alarm signalling devices by means of radio waves.The detectors are multistate in that they report normal pre-alarm fire or fault states to the radio base which transmits the information to the interface. The detectors incorporate drift compensation and report any compensation limit occurring.The radio bases and signalling devices are addressable and use a pre-set analogue value to report via the XP95 or Discovery protocol. Apart from normal and fire the bases can send pre-set analogue values to indicate low battery detector contaminated detector tamper and low signal strength fault conditions.Key FeaturesWirelessBi-directional monitored radio platformChoice of 32 selectable tonesAudible self-test availableOutput is between 92 and 106dbA at 1m dependent on tone setting

GBP 372.43
1

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APO

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APO

Apollo Series 65 Optical Smoke Detector with Flashing LED and Magnetic Test Switch 55000-315APOThe Series 65 Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector and has an indicator LED which is clear in quiescent state but produces a red light in alarm.OperationThe Series 65 Optical Smoke Detector has a moulded self-extinguishing white polycarbonate case with wind resistant smoke inlets. Nickel-plated stainless-steel wiper contacts connect the detector to the base. Inside the case a printed circuit board has the optical system mounted on one side and the signal processing electronics on the other. The sensing chamber is a black moulding configured as a labyrinth which prevents penetration of ambient light. The labyrinth has a fine gauze insect-resistant cover. The chamber houses an infrared light emitting diode LED and a photo-diode which has an integral visible-light filter as extra protection against ambient light. Every three seconds the LED emits a burst of collimated light modulated at 4kHz. In clear air light from the LED does not fall directly on the diode because the LED is positioned at an obtuse angle to the diode. When smoke enters the chamber a fraction of the collimated light is scattered onto the photo-diode. If the resulting signal from the photo-diode is above a pre-set threshold the LED emits two more bursts of light this time at two-second intervals. If light is scattered onto the photo-diode by both these pulses due to the presence of smoke the detector signals an alarm state by switching the alarm latch on increasing the current drawn from the supply from about 40A to a maximum of 75mA. This fall in the impedance of the detector is recognised by the control panel as an alarm signal. The alarm current also illuminates the detector integral LED. A remote indicator connected between the L1 IN terminal and the R terminal will have a voltage equal to the supply voltage less 1 volt across it and so will illuminate. To ensure correct operation of the detector the control panel must be arranged to supply a maximum of 33 Volts dc and a minimum of 9 Volts dc in normal operation. The supply may fall to 6 Volts dc in alarm conditions if a supply current of at least 10mA is available at this voltage. To ensure effective illumination of the integral LED and any remote indicator the supply to the detector should exceed 12 Volts. To restore the detector to quiescent condition it is necessary to expel any smoke and interrupt the electrical supply to the detector for a minimum of one second.Key FeaturesResponds well to slow-burning smouldering firesWell-suited to bedrooms and escape routesUnaffected by wind or atmospheric pressureFlashing LED and magnet operated test switch option

GBP 19.98
1

Apollo Orbis TimeSaver Base - ORB-MB-00001-APO

Apollo Orbis TimeSaver Base - ORB-MB-00001-APO

Apollo Orbis TimeSaver Base - ORB-MB-00001-APOThe Timesaver Base is a design that provides installers with an open working area with fixing holes shaped to allow a fast mounting procedure.Brand InformationOrbis is a range of conventional detectors which has been developed and tested to create advantages for fire engineers and installers as well as owners and users of buildings. Orbis is a range with modern styling and a mounting base that saves installation time. It is electrically compatible with Apollo Series 65 and previous ranges of conventional detector.Orbis is a demonstration of Apollos commitment to the market for high quality conventional detectors for use in small to medium size installations. In developing this range Apollo has put ease of installation and reliability in daily operation at the forefront of considerations. The attractive and compact design means that Orbis will blend in well with all architectural styles.Key Features Grouped terminals to make wiring easyTwo fixing centresLED alignment markCable stripping guideDetector locking mechanism

GBP 3.70
1

Apollo Indoor Intrinsically Safe Manual Call Point 470 ohm - 55100-031APO

Apollo Indoor Intrinsically Safe Manual Call Point 470 ohm - 55100-031APO

Apollo Indoor Intrinsically Safe Manual Call Point 470 ohm - 55100-031APOThe Conventional IS Manual Call Point has been designed to operate on conventional intrinsically safe fire detection systems. Designed specifically for use in atmospheres in which explosive mixtures are or may be present certain design considerations must be observed.The Conventional ISManual Call Point is available in two versions indoor and outdoor.

GBP 23.92
1

Apollo SA4700-302APO Intelligent DIN-Rail Input Output Unit

Apollo SA4700-302APO Intelligent DIN-Rail Input Output Unit

Apollo SA4700-302APO Intelligent DIN-Rail Input Output UnitThe Intelligent DIN-Rail InputOutput Unit providessupervision of one or more normally open volt free contactsconnected to a single pair of cables and a set of changeoverrelay output contacts. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent DIN-Rail InputOutput Unit is designed to be mounted on a 35 mm width DIN-Rail inside an enclosure.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Nine pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsFailsafe mode meets BS 7273-4 requirementsConfigurable input stylesEarth fault monitoring

GBP 56.90
1

Apollo Orbis Marine Optical Smoke Detector with Flashing LED ORB-OP-42003-MAR

Apollo Orbis Marine Optical Smoke Detector with Flashing LED ORB-OP-42003-MAR

Apollo Orbis Marine Optical Smoke Detector with Flashing LED ORB-OP-42003-MARThe Orbis Marine Optical Smoke Detector operates on the well-established light scatter principle. However the sensing technology is radically different in design from previous optical detectors and significantly reduces false alarms.Brand InformationOrbis Marine conventional fire detectors offer a wealth of features to save time enhance reliability and reduce false alarms within the marine environment. These include drift compensation and DirtAlert a feature that warns Service Engineers via a flashing yellow LED that detectors need maintenance and patented FasTest a procedure that takes just four seconds to test smoke detectors and confirm that they are functioning correctly.Key FeaturesResponds well to fast-burning flaming firesReduced false alarmsIncreased reliability of detectionSensing chamber keeps out dust and other airborne contaminantsOperates over a broad range of voltages at extremes of temperatureFlashing LED option

GBP 27.98
1

Apollo Orbis TimeSaver Sav-Wire Base ORB-SW-10005-APO

Apollo Orbis TimeSaver Sav-Wire Base ORB-SW-10005-APO

Apollo Orbis TimeSaver Sav-Wire Base ORB-SW-10005-APOThe Sav-Wire Base is designed to allow Orbis detectors to be used in Sav-Wire detection and alarm systems.Brand InformationOrbis is a range of conventional detectors which has been developed and tested to create advantages for fire engineers and installers as well as owners and users of buildings. Orbis is a range with modern styling and a mounting base that saves installation time. It is electrically compatible with Apollo Series 65 and previous ranges of conventional detector.Orbis is a demonstration of Apollos commitment to the market for high quality conventional detectors for use in small to medium size installations. In developing this range Apollo has put ease of installation and reliability in daily operation at the forefront of considerations. The attractive and compact design means that Orbis will blend in well with all architectural styles.Key Features Grouped terminals to make wiring easyTwo fixing centresLED alignment markCable stripping guideDetector locking mechanismIs used in Sav-Wire systems

GBP 8.86
1

Apollo SA4700-300APO Intelligent DIN-Rail Switch Monitor

Apollo SA4700-300APO Intelligent DIN-Rail Switch Monitor

Apollo SA4700-300APO Intelligent DIN-Rail Switch MonitorThe Intelligent DIN-Rail Switch Monitor is designed tomonitor the state of one or more single pole volt-free contactsconnected on a single pair of cables and to report the status.It has a selectable status reporting delay making it suitable formonitoring flow switches. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent DIN-Rail Switch Monitor is designed to be mounted on a 35 mm width DIN-Rail inside an enclosure.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Five pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsConfigurable input stylesEarth fault monitoring

GBP 47.69
1

Apollo Orbis Marine Optical Smoke Detector ORB-OP-42001-MAR

Apollo Orbis Marine Optical Smoke Detector ORB-OP-42001-MAR

Apollo Orbis Marine Optical Smoke Detector ORB-OP-42001-MARThe Orbis Marine Optical Smoke Detector operates on the well-established light scatter principle. However the sensing technology is radically different in design from previous optical detectors and significantly reduces false alarms. Orbis Marine conventional fire detectors offer a wealth of features to save time enhance reliability and reduce false alarms within the marine environment.These include drift compensation and DirtAlert a feature that warns Service Engineers via a flashing yellow LED that detectors need maintenance and patented FasTest a procedure that takes just four seconds to test smoke detectors and confirm that they are functioning correctly.Key FeaturesResponds well to fast-burning flaming firesReduced false alarmsIncreased reliability of detectionSensing chamber keeps out dust and other airborne contaminantsOperates over a broad range of voltages at extremes of temperatureBrand FeaturesApproved for use in marine environmentsModern low-profile designTimeSaver Base for fast installationTransient rejection for false alarm reductionHigh humidity tolerance at up to 98 RHWide operating temperature -40C to 70C

GBP 27.98
1

Apollo SA4700-103APO Intelligent Mains Switching Input Output Unit

Apollo SA4700-103APO Intelligent Mains Switching Input Output Unit

Apollo SA4700-103APO Intelligent Mains Switching Input Output UnitThe Intelligent Mains Switching InputOutput Unit provides asingle line tolerant circuit CoreProtocol only containing oneor more normally open contacts connected to a single pair of cables. It also provides a voltage free change over relay outputcapable of switching mains. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Nine pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsTwo input channelsFailsafe mode meets BS 7273-4 requirementsConfigurable input stylesEarth fault monitoring

GBP 69.41
1

Apollo AlarmSense Sounder Beacon Base 45681-509APO

Apollo AlarmSense Sounder Beacon Base 45681-509APO

Apollo AlarmSense Sounder Beacon Base 45681-509APOThe AlarmSense Sounder Visual Indicator Base is designed to be used with AlarmSense systems only. It is supplied with a low or high volume setting and red or white caps are available for stand-alone installation.Brand InformationAlarmSense is a range of conventional fire detection and alarm products designed to be connected to the same pair of supply wires making installation quicker and less expensive. AlarmSense has been developed to make the design and installation of a fire detection and alarm system easier and more economic for small to medium-sized buildings. The range also allows an existing system to be extended or modified if necessary.This flexibility makes AlarmSense an excellent choice for use in HMOs House in Multiple Occupation. As you would expect from Apollo AlarmSense incorporates features that help reduce false alarms and patented technology to ensure the integrity of a system. The range also includes products such as beacons to help meet the requirements of the Disability Discrimination Act DDA.Key FeaturesSounder range between 70dBA and 87dBADetects the removal of a detector head and reports a faultContinues to work during unauthorised removal of detectorsQuick and simple installation

GBP 33.06
1

Apollo Orbis TimeSaver Deep Base - ORB-MB-00019-APO

Apollo Orbis TimeSaver Deep Base - ORB-MB-00019-APO

Apollo Orbis TimeSaver Deep Base - ORB-MB-00019-APOThe TimeSaver Deep Base is a mounting base for Orbis products which has an increased depth which allows for cables to be inserted into the side of the product.Brand InformationOrbis is a range of conventional detectors which has been developed and tested to create advantages for fire engineers and installers as well as owners and users of buildings. Orbis is a range with modern styling and a mounting base that saves installation time. It is electrically compatible with Apollo Series 65 and previous ranges of conventional detector.Orbis is a demonstration of Apollos commitment to the market for high quality conventional detectors for use in small to medium size installations. In developing this range Apollo has put ease of installation and reliability in daily operation at the forefront of considerations. The attractive and compact design means that Orbis will blend in well with all architectural styles.Key Features Grouped terminals to make wiring easyTwo fixing centresLED alignment markCable stripping guideDetector locking mechanismEnables surface wiring

GBP 6.04
1

Apollo AlarmSense Base 45681-244APO

Apollo AlarmSense Base 45681-244APO

Apollo AlarmSense Base 45681-244APOAlarmSense detectors can only be mounted into the AlarmSense Base. The base is used for installing detectors that do not require an integral sounder or sounder visual indicator. AlarmSense is a range of conventional fire detection and alarm products designed to be connected to the same pair of supply wires making installation quicker and less expensive.AlarmSense has been developed to make the design and installation of a fire detection and alarm system easier and more economic for small to medium-sized buildings. The range also allows an existing system to be extended or modified if necessary. This flexibility makes AlarmSense an excellent choice for use in HMOs House in Multiple Occupation.As you would expect from Apollo AlarmSense incorporates features that help reduce false alarms and patented technology to ensure the integrity of a system. The range also includes products such as beacons to help meet the requirements of the Disability Discrimination Act DDA.Key FeaturesDetects the removal of a detector head and reports a faultContinues to work during unauthorised removal of detectorsQuick and simple installationBrand FeaturesFlexibleReliableCost-effectiveCompliant with BS 5839Easy to installEasy to extend

GBP 4.45
1

Apollo SA4700-102APO Intelligent Input Output Unit

Apollo SA4700-102APO Intelligent Input Output Unit

Apollo SA4700-102APO Intelligent Input Output UnitThe Intelligent InputOutput Unit provides supervision of oneor more normally open contacts connected to a single pair ofcables and a set of changeover relay output contacts. Compatible with XP95 Discovery and CoreProtocol digital communication protocols.Mechanical ConstructionThe Intelligent InputOutput Unit is available in the new faceplate style enclosure. This can be mounted with the supplied back-box for surface mounting or flush mounted using a UK double gang flush mounting back-box of minimum depth 30mm.OperationThe Intelligent InputOutput Unit provides supervision of one or more normally open contacts connected to a single pair of cables and a set of changeover relay output contacts.Key FeaturesImproved design for ease of wiring meaning faster installationContains controllable isolatorAddress range 1 - 254Nine pre-configured modes including compatibility mode from XP95Discovery to CoreProtocol systemsFailsafe mode meets BS 7273-4 requirementsConfigurable input stylesEarth fault monitoring

GBP 55.15
1

Apollo AlarmSense Sounder Base 45681-510APO

Apollo AlarmSense Sounder Base 45681-510APO

Apollo AlarmSense Sounder Base 45681-510APOThe AlarmSense Sounder Base can only be used with AlarmSense systems. It is fitted with electronic circuitry to monitor the presence of detectors and signals any unauthorised removal of detector heads. It is supplied with a high or low volume setting and red or white capsare available for stand-alone installation.Brand InformationAlarmSense is a range of conventional fire detection and alarm products designed to be connected to the same pair of supply wires making installation quicker and less expensive.AlarmSense has been developed to make the design and installation of a fire detection and alarm system easier and more economic for small to medium-sized buildings. The range also allows an existing system to be extended or modified if necessary. This flexibility makes AlarmSense an excellent choice for use in HMOs House in Multiple Occupation.As you would expect from Apollo AlarmSense incorporates features that help reduce false alarms and patented technology to ensure the integrity of a system. The range also includes products such as beacons to help meet the requirements of the Disability Discrimination Act DDA.Brand FeaturesFlexibleReliableCost-effectiveCompliant with BS 5839Easy to installEasy to extendKey FeaturesAlarmSense prioritynon priority signal recognitionDetects the removal of a detector head and reports a faultContinues to work during unauthorised removal of detectorsQuick and simple installationProvides audible signal and detection at one pointHigh and low volume ranges

GBP 22.99
1