120 results (0,15959 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Aritech ATS1236 Wireless DGP Receiver 433MHz - In Plastic Housing EN Grade 2

Aritech ATS1236 Wireless DGP Receiver 433MHz - In Plastic Housing EN Grade 2

Aritech ATS1236 Wireless DGP Receiver 433MHz - In Plastic Housing EN Grade 2The ATS1236 wireless receiver adds wireless capabilities to the Advisor Advanced range of panels.The wireless DGP supports most of the legacy 433 MHz 63-bit transmitters as well as the new generation of 433 MHz LoNa transmitters of which the wireless communication is fully encrypted avoiding unauthorized interference. Up to 32 wireless sensors and up to 16 keyfobs can be learned in.The ATS1236 wireless receiver provides two wired zone inputs and one programmable relay output.Installation and programmingThe wireless DGP needs to be installed outside the panel housing in order to assure a maximum wireless range. The 433MHz wireless solution will monitor the status and presence of each wireless device and will respond in case of an RF jamming condition.The ATS1236 wireless receiver can be programmed from the keypad as well as from the downloader. The firmware of the module is remotely upgradeable.Key FeaturesAdds wireless capabilities to Advisor AdvancedTwo wired zone inputsOne programmable SPDT Form C relay outputSupports legacy 63-bit 433 MHz and new LoNa 433 MHz transmittersLearn-mode technologyRemovable terminalsEN50131-1EN50131-3EN50131-6 Grade 2 Class II pending INCERT pendingFirmware upgradeable

GBP 170.80
1

Aritech ATS1235 Receiver 868 Gen2 - In Plastic Housing Grade 2

Aritech ATS1235 Receiver 868 Gen2 - In Plastic Housing Grade 2

Aritech ATS1235 Receiver 868 Gen2 - In Plastic Housing Grade 2The ATS1235 Advanced Wireless Data Gathering Panel DGP receiver adds wireless capabilities to the Axon Advisor Advanced Master panels using Aritech 868 MHz Gen 2 Wireless Sensors i.e. PIR Glassbreak etc. Maximum distance from the panel is 1500 m. The ATS1235 features spatial diversity to minimize wireless signal nulls or dead spots and has a nominal open-air receiving range of 400 m. If dead spots need to be eliminated a 868 MHz repeater may be used. It can be powered from the control panel databus or a remote auxiliary power supply.Fob buttons may be programmed for users to arm and disarm or to control relays.With ATS1235 Advanced wireless expanders the control panel becomes a hybrid system where one can optimize the system by distributing receivers in the premises.The ATS1235 is EN50131 Grade 2 approved.Key FeaturesExpands the Axon panel or the Advisor Advanced panel with 32 wireless zones868 MHz Wireless GEN2 SensorsQuick configuration using the Aritech Learn Mode technologyFeatures spatial diversity to minimize wireless dead spots and has a nominal open-air receiving range of 460 mUse the Aritech 868 MHz repeater to improve rangePowered from the control panel databus or a remote auxiliary power supplyFob buttons may be programmed for users to arm and disarm or to control relaysTo remotely open and close a garage door as well as arm or disarm an office security system

GBP 128.23
1

Aritech II952ND Intelligent Switch Monitor DIN Rail Mount Apollo equivalent SA4700-300

Aritech II952ND Intelligent Switch Monitor DIN Rail Mount Apollo equivalent SA4700-300

Aritech II952ND Intelligent Switch Monitor DIN Rail Mount Apollo equivalent SA4700-300II952ND Apollo Switch Monitor Unit is the new DIN-Rail switch monitor unit designed to monitor the state of one or more single pole volt-free contacts connected on a single pair of cables to report the status. It has a selectable status reporting delay making it suitable for monitoring flow switches.Key FeaturesImproved design for ease of wiring meaning faster installationLoop poweredSupervise one or more single pole volt-free contacts connected on a single pair of cablesLocal LEDs signalling IO and fault conditionsIsolators within each device

GBP 128.20
1

Aritech II954NI Intelligent Twin Switch Monitor Unit Apollo equivalent SA6700-100

Aritech II954NI Intelligent Twin Switch Monitor Unit Apollo equivalent SA6700-100

Aritech II954NI Intelligent Twin Switch Monitor Unit Apollo equivalent SA6700-100II954NI is the new twin switch monitor unit which provides the function of two switch monitor units within one enclosure. The two units are electrically independent of each other. There is a DIL switch on each unit to set the address. Both the units are designed to monitor the state of one or more single pole volt-free contacts connected on a single pair of cables to report the status. It has a selectable status reporting delay making it suitable for monitoring flow switches.Mechanical ConstructionThe II952NI is available in the new faceplate style enclosure. It is designed to be surface mounted to the wall and consists of 3 parts - a backbox with knock-outs for cable entry - a PCB assembly - a protective front coverEase of Installation Improved design for ease of wiring meaning faster installation unit can be fitted to back-box before wiring is connected. Colour coded terminal blocks for easier identification green for loop wiring yellow for mains wiring grey for inputs and low voltage relays.Key FeaturesImproved design for ease of wiring meaning faster installationLoop poweredEach unit supervise one or more single pole volt-free contactsconnected on a single pair of cablesLocal LEDs signalling IO and fault conditionsIsolators within each device

GBP 154.70
1

Aritech DF410 Wireless Gate Sensor Module Battery Powered - Grey

Aritech DF410 Wireless Gate Sensor Module Battery Powered - Grey

Aritech DF410 Wireless Gate Sensor Module Battery Powered - GreyThe FlexZone Wireless Gate Sensor consists of two main components the sensor module and a receiver card installed inside a FlexZone processor. The sensor module analyses vibration motion and position data. It transmits intrusion and supervision alarms power levels RF link status and auxiliary input state to the receiver card over the encrypted wireless link.Key FeaturesDetect intrusion attempts on sliding and swinging gates Detect intrusion attempts on sliding and swinging gatesWireless operation eliminates need to route cables from fence to moving gate panels300 m transmission range from FlexZone processorSupervised input for auxiliary device alarm reporting

GBP 949.10
1

Aritech II950I 950 Series Mini Switch Monitor with Isolator

Aritech II950I 950 Series Mini Switch Monitor with Isolator

Aritech II950I 950 Series Mini Switch Monitor with IsolatorThe II950I is a 950 series addressable mini switch monitor. It can be fitted onto a 35 mm DIN-Rail with a twist-click motion or mounted in an enclosure such as a manual call point. The II950I is designed to monitor the state of one or more single pole volt free contacts connected to a single pair of cables and to report this status back to the control panel.Interrupt facilityWith this feature enabled the II950I performs the same tasks as in standard mode but simulates the same response functionality as an addressable manual call point. In this mode the II950I may be used to monitor equipment where a fast response is required. An alarm will be reported to the control panel in less than 3 seconds.SupervisionThe II950I allows for full supervision of the monitored input i.e. both open and short circuit fault detection are enabled. Any problems with this input cabling will be indicated by and LED on the unit as well as reported back to the control equipment. The II950I is able to monitor for pre-alarm as well as alarm states.Ease of MaintenanceThe II950I includes 3 functional indicatorsa green LED for normal operationa yellow LED for isolation ON or fault pulsea red LED for alarmThese status LEDs allow a maintenance engineer to evaluate the status of the unit without having to return to the control panel.Key FeaturesLoop poweredMicro unit only 39 x 39 x 20 mmCan be mounted inside other equipmentBuilt in short circuit isolatorInterrupt or non-interrupt selectableFully supervised input with pre-alarm functionLED indications for normal isolated fire and fault conditionsApollo equivalent 55000-760

GBP 77.46
1

Aritech RF320I4B-N Wireless DoorWindow Sensor Brown 433 MHz 63 Bit

Aritech RF320I4B-N Wireless DoorWindow Sensor Brown 433 MHz 63 Bit

Aritech RF320I4B-N Wireless DoorWindow Sensor Brown 433 MHz 63 BitEach RF receiver monitors the alarm battery tamper and supervisory status of each transmitter. In addition it reports any change in status to the panel which takes action according to the programmed zone types.Key FeaturesLearn-Mode TechnologyMore than 3 years battery life2 internal reed switches allow for vertical or horizontal mountingWall and cover tamperJumper to select one of the 2 reed switcher or the supervised external input

GBP 70.82
1

Aritech RF320I4-N Wireless DoorWindow Sensor White 433 MHz 63 Bit

Aritech RF320I4-N Wireless DoorWindow Sensor White 433 MHz 63 Bit

Aritech RF320I4-N Wireless DoorWindow Sensor White 433 MHz 63 BitEach RF receiver monitors the alarm battery tamper and supervisory status of each transmitter. In addition it reports any change in status to the panel which takes action according to the programmed zone types.Key FeaturesLearn-Mode TechnologyMore than 3 years battery life2 internal reed switches allow for vertical or horizontal mountingWall and cover tamperJumper to select one of the 2 reed switcher or the supervised external input

GBP 70.82
1

Aritech DD669AM 20m Ceiling Mount Dual Technology Detector With Active IR Anti-Mask 18 Curtains. NC Relay Grade 3

Aritech DD669AM 20m Ceiling Mount Dual Technology Detector With Active IR Anti-Mask 18 Curtains. NC Relay Grade 3

Aritech DD669AM 20m Ceiling Mount Dual Technology Detector With Active IR Anti-Mask 18 Curtains. NC Relay Grade 3The DD600 series complement the successful EV600 series PIRs with dual technology motion sensors. The 18 curtains offer a maximum detection capability including full under crawl detection throughout a protected area of up to 20m in diameter.The unique mirror optics technology is a gliding focus which creates continuous curtains that never loses track of the intruder.4D signal processing4D signal processing makes an effective discrimination between intruder and false alarm signals. Recognizing the diversity in security applications the DD600 series features both 4D signal processing and Bi-curtain processing for the harsher environments. The combination of mirror optics with 4D signal processing not only provides better detection but also increased stability and rejection of false alarms.Range controlled radarThe DD600 sensors incorporate a unique radar technology that is range controlled and operates on 5.8 GHz frequency. The range control means that no nuisance alarms are generated for movements beyond the detection pattern.Key FeaturesDual motion sensorAutomatic reporting of all masking attemptsStep Gliding Focus Multi Curtain mirror opticRange controlled radar on 5.8 GHzPlug-in electronicsSealed optics4D processing for reduced nuisance alarmsSelectable coverage pattern using mirror masksAdditional bi-curtain processing for harsh environmentNo adjustment required for different mounting heightsEN50131-2-4 Grade 3 certifiedSeveral European approvals

GBP 206.77
1

Aritech DC120S60 1125W N1 Aritech With 6m VdS Cable

Aritech DC120S60 1125W N1 Aritech With 6m VdS Cable

Aritech DC120S60 1125W N1 Aritech With 6m VdS CableThe DC120 magnetic contact is designed specifically for applications where space is limited. The short length makes it ideal for thin framed windows and doors where longer units cannot be used. Press fit ribs on the housing make for quick and easy installation.InstallationThe hermetically-sealed reed switch is potted using exclusive polyurethane compound. Switch and Alnico V magnet is drill-mounted in wood or aluminium with a suitable adhesive. The switch and magnet housing have three fins to press-fit against the mounting hole.Key FeaturesSwitch only 19 mm long ideal for installation in thin framed doors and windowsWith 18 mm gap distance for faster installationIdeal for pre-wiring eliminates forcing switch and pre-wire into same header holeAvailable in different cable lengthsTamper loop provided

GBP 20.39
1

Aritech ATS1500A-IP-MBC ATS1500A-IP Spare PCB MR4 PCB Supporting Ultrasync

Aritech ATS1500A-IP-MBC ATS1500A-IP Spare PCB MR4 PCB Supporting Ultrasync

Aritech ATS1500A-IP-MBC ATS1500A-IP Spare PCB MR4 PCB Supporting UltrasyncA spare PCB supporting Ultrasync.Key Features8 onboard zone inputsMax 32 zones wired wireless or mixedEconomic input and output plug-in expansionUp to 16 shock sensor inputs4 areasUp to 50 usersEN50131 Grade 3 when ATS-MM-TK added Environmental class 2USB port for local configurationPlug-on PSTN dialler for reporting or configurationMultilingual language configurable per userIntegrated 10100Mb Ethernet connectionIP alarm reporting to OH-NETREC receiver - Optional GPRSIntegrated access control support for ATS125x door controller

GBP 362.57
1

Aritech DM796 Break Glass Key Box

Aritech DM796 Break Glass Key Box

Aritech DM796 Break Glass Key BoxThe DM796 is a high quality RED plastic key box with supervision. When the breakable element is broken to remove the key or access card inside the unit the micro switch is activated. The micro switch has a normally open and normally closed contact.Key FeaturesEasy to installSurface mountingHigh quality micro switchNormally open and normally closed contactsReplaceable breaking elementKey or access card can be fitted inside

GBP 59.42
1

Aritech RF-4041-07-2 2-Way Key Fob LoNa Technology

Aritech RF-4041-07-2 2-Way Key Fob LoNa Technology

Aritech RF-4041-07-2 2-Way Key Fob LoNa TechnologyThis 4-button 2-way key fob using the latest LoNa technology allows the end-user to arm disarm or partially arm their system without having to memorize access codes or race to beat entry or exit delays.Each button press will be indicated by a blinking LED and the acknowledgement coming from the receiver will also trigger the LED on the key fob.In case the system is not ready to arm or in case the end-user is out-of-range of the receiver this will also be visible on the key fob when pressing a button. Even a system in alarm will be indicated when performing a button press.It offers one additional programmable buttons which can be used e.g. to turn on and off lights before entering the premises activate an automated garage door etc.It can also be used to send a panic alarm by pressing the lock and unlock buttons simultaneously or to trigger an auxiliary alarm by pressing the 1 and 2 button simultaneously.This variant can be used in the ZeroWire and XGen eco-systems.Key FeaturesUsing LoNa technologyCompact robust premium designLED confirmation of sent and received messagesOut-of-range LED indication1 programmable buttonPanic and Auxiliary alarm functionality available5 years of battery life based on usageEN Incert security approvals

GBP 55.58
1

Aritech DMN960Y 990 Series Manual Call Point - Complete with Back Box and Resettable Element Yellow

Aritech DMN960Y 990 Series Manual Call Point - Complete with Back Box and Resettable Element Yellow

Aritech DMN960Y 990 Series Manual Call Point - Complete with Back Box and Resettable Element YellowThe DMN960Y is a surface mount YELLOW addressable 990 Series manual call point with a high strength plastic housing. The LED indicator provides visual confirmation of alarm initiation. The test key included with each unit facilitates functional testing of the call point. The manual call point is delivered complete with resettable element.Operating PrinciplesThe address of each call point is set at the commissioning stage by means of a seven-segment DIL switch. The device features plug and play terminal connections. A single alarm LED is provided on the call point and is controlled independently of the call point by the fire panel.AccessoriesIt is possible to surface or flush mount any of the call points in the range. Optional accessories to accommodate this are available separately.ApprovalsAll relevant manual call points in the range have been tested by LPC and approved by LPCB and a number of other approval authorities.Key FeaturesAddressable manual call pointLED alarm indicatorTamper resistant break glass designEasy to test with self-resetFast responsePlug and play terminal connections for fast wiringAllow wiring continuity testing before fittingResettable element fitted

GBP 70.24
1

Aritech DB702 Dx700 Series Conventional Point Detector Base - 10cm

Aritech DB702 Dx700 Series Conventional Point Detector Base - 10cm

Aritech DB702 Dx700 Series Conventional Point Detector Base - 10cmThe Aritech DB702 is a conventional fire detector base used for all 700 series conventional fire detectors. It includes a normally closed continuity switch to allow for easy cable testing during installation. Inserting a detector into the base opens the continuity switch in the base to allow for standard open circuit monitoring. A locking mechanism implementation in conjunction with the detector allows for the detector to be safeguarded against unauthorized removal.Key FeaturesOne way only fitLocking mechanism providedInsert detectors without force

GBP 3.86
1