24 results (0,17042 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

4x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote Relay Outputs)

4x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote Relay Outputs)

An optional system expansion device for use with CFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels. Provides four panel-controlled volt free relay outputs (reset, fault, aux. fire and remote). PCB mounts inside the CFP fire panel. Reset relay is active during the panels reset cycle. Fault relay is active in any fault condition. This relay is failsafe and normally energised if power is removed from the panel the relay will changeover to produce a fault signal. Aux. fire relay is active in an alarm condition provided all relevant delays have expired. Remote relay is active during any Alarm Condition provided all relevant delays have expired. Outputs are NOT designed to switch mains voltages.

GBP 239.96
1

3x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote & 8 Output Per Zone Relays)

3x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote & 8 Output Per Zone Relays)

An optional system expansion device for use with CFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels. Provides four panel-controlled volt free relay outputs (reset, fault, aux. fire and remote) and eight output per zone relays. PCB mounts inside the CFP fire panel. Reset relay is active during the panels reset cycle. Fault relay is active in any fault condition. This relay is failsafe and normally energised if power is removed from the panel the relay will changeover to produce a fault signal. Aux. fire relay is active in an alarm condition provided all relevant delays have expired. Remote relay is active during any Alarm Condition provided all relevant delays have expired. Output per zone relays will changeover when the corresponding zone is in alarm (subject to certain conditions for full details refer to the instructions, downloadable below). Outputs are NOT designed to switch mains voltages.

GBP 239.97
1

10x C-TEC ActiV Relay Base with Diode

10x C-TEC ActiV Relay Base with Diode

Compatible with C-TECs entire range of ActiV firedetectors. Includesa1A @ 24 VDC relay controlled by detectors remote LED output. Ideal for switching CCTV, security and door retaining systems. Third-party certified to the relevant parts of EN54 in conjunction with our ActiV detectors. Easy to fit with lots of working space. Can be ceiling mounted in any orientation due to the true 360 degree viewing angle of the LED indicator strips on all ActiV detectors. Integrated detector/base locking mechanism, head removal tool and ID tag. Simple click and twist design. Remote LED terminals for the optional connection to a BF318 Remote indicator. C4408R non-diode relay base also available for use on systems that do not require head out monitoring.

GBP 209.90
1

10x C-TEC 4.2m (14ft) Tail Call Lead

10x C-TEC 4.2m (14ft) Tail Call Lead

A long 4.2m tail call lead for use with C-TECs Quantec and 800 Series Call Systems. Allows usersto remotely generate Standard calls from armchairs, beds, etc. Comprises a pear-shaped call push, 4.2m(14ft) trailing lead and a 6.35mm remote jack plug. Easily connects to the 6.35mmremote socket on compatible Quantec and 800 Series call points. Activating the pear push or removing the tail call lead from a call points remote socket will generate a Standard call.

GBP 199.90
1

12x C-TEC 1.8m (6ft) Tail Call Lead

12x C-TEC 1.8m (6ft) Tail Call Lead

A short 1.8mtail call lead for use with C-TECs Quantec and 800 Series Call Systems. Allows usersto remotely generate Standard calls from armchairs, beds, etc. Comprises a pear-shaped call push, 1.8m (6ft) trailing lead and a 6.35mm remote jack plug. Easily connects to the 6.35mmremote socket on compatible Quantec and 800 Series call points. Activating the pear push or removing the tail call lead from a call points remote socket will generate a Standard call.

GBP 203.88
1

4x C-TEC Emergency Call Point, Button Reset c/w Remote Socket

4x C-TEC Emergency Call Point, Button Reset c/w Remote Socket

An attractively designed button-operated call/reset point capable of generating Standard and Emergency calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead, pressure mat or other ancillary caling device. Red reassurance LED confirms a call has been made. Onboard reset button cancels Standard and Emergency calls made from the NC802DEB-1/2 and Standard calls made from other devices wired on the same zone (such as ceiling pull units in Ensuite areas). Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 211.96
1

6x C-TEC Standard Call Point, Button Reset c/w Remote Socket

6x C-TEC Standard Call Point, Button Reset c/w Remote Socket

An attractively designed button-operated call/reset point capable of generating Standard calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead, pressure mat or other ancillary caling device. Red reassurance LED confirms a call has been made. Onboard reset button cancels calls made from the NC802DB and standard calls made from other devices wired on the same zone (such as ceiling pull units in Ensuite areas). Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 179.94
1

2x C-TEC 12V 2A EN54-4 Switch Mode PSU

2x C-TEC 12V 2A EN54-4 Switch Mode PSU

Certified to EN54-4/A2 by the LPCB &VdS (AFNOR pending). A powerful switch mode/digital hybrid PSU that can be customised* to suit your exact requirements see More Information tab for details. Plastic cover on PSU PCB guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition. Multiple indicators supply present, general fault, fault type & aux. equipment fault. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Ideal for connecting to 12V security STUs to provide BS5839-1 compliant remote monitoring facilities. Electronic functions comply with EN50131-6 grades 1-4 for security applications. BF560-12/E EncasedPCB version also available.

GBP 259.98
1

4x C-TEC Master Infrared Ceiling Receiver

4x C-TEC Master Infrared Ceiling Receiver

A ceiling-mountable infrared receiver that will accept Standard & Emergency calls from compatible 800 Series infrared transmitters. Can receive line-of-sight infrared signals from around 10m away (dependent on physical conditions and environmental factors). Red reassurance LED confirms a call has been made. Requires a separate remote reset point such as our NC802DB button reset or NC899IRR keyswitch reset point for cancelling calls. Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 279.96
1

5x C-TEC Chair Exit Mat

5x C-TEC Chair Exit Mat

Designed to trigger a call by sensing the pressure change when a patient exits a chair. Connects to Quantec via the remote jack socket on a QT637 Enuresis/General Purpose Interface Socket or QT636 Interface Unit. To reduce the risk of nuisance calls, the QT637 includes circuitry that prevents a momentary change in pressure such as a patient quickly changing position from triggering a call. Measures 400mm x 250mmand is supplied with a 2m lead and normally closed right angled jack plug.

GBP 219.95
1

5x C-TEC Bed Exit Mat

5x C-TEC Bed Exit Mat

Designed to trigger a call by sensing the pressure change when a patient exits a bed. Connects to Quantec via the remote jack socket on a QT637 Enuresis/General Purpose Interface Socket or QT636 Interface Unit. To reduce the risk of nuisance calls, the QT637 includes circuitry that prevents a momentary change in pressure such as a patient quickly changing position from triggering a call. Typically positioned across and overamattress, directly underneath the bedsheet. Measures 80cm x 10cm and is supplied with a 2m lead and normally closed right angled jack plug.

GBP 199.95
1

C-TEC 24V 5A EN54-4 Switch Mode PSU

C-TEC 24V 5A EN54-4 Switch Mode PSU

Certified to EN54-4/A2 by the LPCB and VdS. A powerful 24V 5A switch mode/digital hybrid PSU that can be customised* to suit your exact requirements see More Information tab for details. Plastic cover on PSU PCB guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition. Multiple indicators supply present, general fault, fault type & aux. equipment fault. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications. BF562-5/E encasedversion also available.

GBP 209.99
1

C-TEC 24V 3A EN54-4 Switch Mode PSU

C-TEC 24V 3A EN54-4 Switch Mode PSU

Certified to EN54-4/A2 by the LPCB and VdS. A powerful 24V 3A switch mode/digital hybrid PSU that can be customised* to suit your exact requirements see More Information tab for details. Plastic cover on PSU PCB guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition. Multiple indicators supply present, general fault, fault type & aux. equipment fault. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications. BF562-3/E encasedversion also available.

GBP 159.99
1

C-TEC CFP 8 Zone Repeater Panel

C-TEC CFP 8 Zone Repeater Panel

Can be used to repeat the functions of a master CFP standard or AlarmSense 2-8 zone fire panel at remote parts of site (e.g. all potential fire service entrances). Up to 8 repeaters per CFP master. Includes its own Mains power supply that requires its own standby battery supply. Provides the user with access to all AL1 and AL2 functions. Master/Repeater communication achieved using CFP761 network driver cards (one CFP761 is supplied with the Repeater, an additional CF761 card is required at the master CFP). Communicates over screened two-wire fire resistant cable. Total repeater network cable length should not exceed 1KM. Attractive flush or surface mountable plastic lid and enclosure no bezel required.

GBP 199.99
1

3x C-TEC 12V 2A Encased Switch Mode PSU to EN54-4/A2

3x C-TEC 12V 2A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF560-12 LPCBcertified EN54-4/A2 boxed 12V 2A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole voltfree changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 257.97
1

2x C-TEC 24V 1.5A Encased Switch Mode PSU to EN54-4/A2

2x C-TEC 24V 1.5A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF560-24LPCBcertified EN54-4/A2 boxed 24V 1.5A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole volt-free changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 179.98
1

C-TEC XFP 16 Zone Repeater Panel (all protocols)

C-TEC XFP 16 Zone Repeater Panel (all protocols)

Can be used to repeat the functions of an XFP Main panel at remote parts of a site (e.g. all potential fire service entrances). Offers all of the functions and controls of an XFP Main panel (access levels 1, 2 and 3). Includes an on-board fault relay. Requires its own dedicated Mains power and battery back-up supply. A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel. Communication between the XFP Main panel and Repeater requires a CFP761 network driver card (fitted as standard in all XFP510-16s, available as an optional extra on Main XFP 16 Zone panels). Repeater network wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.

GBP 299.99
1

2x C-TEC 24V 5A Encased Switch Mode PSU to EN54-4/A2

2x C-TEC 24V 5A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF562-5 LPCB/VDS certified EN54-4/A2 boxed 24V 5A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole volt-free changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 259.98
1

2x C-TEC 24V 3A Encased Switch Mode PSU to EN54-4/A2

2x C-TEC 24V 3A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF562-3 LPCB/VDS certified EN54-4/A2 boxed 24V 3A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole volt-free changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 219.98
1

C-TEC XFP 32 Zone Repeater Panel (all protocols)

C-TEC XFP 32 Zone Repeater Panel (all protocols)

Can be used to repeat the functions of an XFP Main panel at remote parts of a site (e.g. all potential fire service entrances). Offers all of the functions and controls of an XFP Main panel (access levels 1, 2 and 3). Includes an on-board fault relay. Requires its own dedicated Mains power and battery back-up supply. A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel. Communication between the XFP Main panel and Repeater requires an AFP711 network driver card (fitted as standard in all XFP510-32s, available as an optional extra on Main XFP 32 Zone panels). Repeater network is non-redundant and wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.

GBP 439.99
1