44 results (0,18048 seconds)

Show all filters

Brand

Colour

Merchant

Price (EUR)

Reset filter

Products
From
Shops

4x C-TEC Master Infrared Ceiling Receiver

4x C-TEC Master Infrared Ceiling Receiver

A ceiling-mountable infrared receiver that will accept Standard & Emergency calls from compatible 800 Series infrared transmitters. Can receive line-of-sight infrared signals from around 10m away (dependent on physical conditions and environmental factors). Red reassurance LED confirms a call has been made. Requires a separate remote reset point such as our NC802DB button reset or NC899IRR keyswitch reset point for cancelling calls. Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 279.96
1

7x C-TEC Call Latch Module

7x C-TEC Call Latch Module

A discreetmonitoring modulethat allows any device with a normally open or normally closed switch to generate aStandard call on an 800 Series Call System. Measures just 25 x 20 x 15mm ideal for locating inside or alongside themonitored device. Red reassurance LED illuminates when a call is made. Can be connected topanic buttons, door bells,radio receiver transmitter pairs, ultra-sonic receiver transmitter pairs, etc. Requires a separate reset point. Mountsusing a self-adhesive pad (supplied).

GBP 328.93
1

2x C-TEC RF Integrity Heartbeat Transmitter

2x C-TEC RF Integrity Heartbeat Transmitter

The QT421 Monitored RF Integrity Transmitter is intended for use with QuantecsQT422RX Radio Receivers. Helps ensureRFintegrity and site coverage at all timesby sending aperiodic RF test transmission toReceivers with thesame RF group address. Flags a fault at the Quantec Controller if a transmission isnot received. Typically located at strategic points on the installation we recommend at least one RF Integrity Transmitter is used per Radio Receiver. Mountable on a 25mm UK single gang back box. Takes its power from the Quantec network but is not an addressable device as it is monitored by the radio receiver(s) it is set to work with.

GBP 267.98
1

C-TEC 24V 5A EN54-4 Switch Mode PSU

C-TEC 24V 5A EN54-4 Switch Mode PSU

Certified to EN54-4/A2 by the LPCB and VdS. A powerful 24V 5A switch mode/digital hybrid PSU that can be customised* to suit your exact requirements see More Information tab for details. Plastic cover on PSU PCB guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition. Multiple indicators supply present, general fault, fault type & aux. equipment fault. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications. BF562-5/E encasedversion also available.

GBP 209.99
1

C-TEC 24V 3A EN54-4 Switch Mode PSU

C-TEC 24V 3A EN54-4 Switch Mode PSU

Certified to EN54-4/A2 by the LPCB and VdS. A powerful 24V 3A switch mode/digital hybrid PSU that can be customised* to suit your exact requirements see More Information tab for details. Plastic cover on PSU PCB guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition. Multiple indicators supply present, general fault, fault type & aux. equipment fault. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications. BF562-3/E encasedversion also available.

GBP 159.99
1

2x C-TEC Rechargeable IR/RF Transmitter (push/pull for attack)

2x C-TEC Rechargeable IR/RF Transmitter (push/pull for attack)

Allows staff working in high-risk environments to remotely trigger an Attack call via a Quantec infrared call point, ceiling receiver or radio receiver Can also be used on 800 Series call systems to trigger Standard and Emergency calls via an800 Series infrared receiving device. 10m line-of-sight IR transmitting range. Radio coverage dependent on the Quantec receiving device used. Includes a Karabiner clip for attaching to staff uniforms. Calls are triggered by pulling the transmitters retaining clip or activating one ofits two buttons. Can be recharged using a QT424/1 single-way or QT424/10 ten-way charging unit. Can be programmed to generate different call levels using a QT423 configurator. Transmitters used on Quantec systems can also be programmed to includeaunique User ID/name.

GBP 299.98
1

2x C-TEC 12V 2A EN54-4 Switch Mode PSU

2x C-TEC 12V 2A EN54-4 Switch Mode PSU

Certified to EN54-4/A2 by the LPCB &VdS (AFNOR pending). A powerful switch mode/digital hybrid PSU that can be customised* to suit your exact requirements see More Information tab for details. Plastic cover on PSU PCB guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition. Multiple indicators supply present, general fault, fault type & aux. equipment fault. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Ideal for connecting to 12V security STUs to provide BS5839-1 compliant remote monitoring facilities. Electronic functions comply with EN50131-6 grades 1-4 for security applications. BF560-12/E EncasedPCB version also available.

GBP 259.98
1

4x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote Relay Outputs)

4x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote Relay Outputs)

An optional system expansion device for use with CFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels. Provides four panel-controlled volt free relay outputs (reset, fault, aux. fire and remote). PCB mounts inside the CFP fire panel. Reset relay is active during the panels reset cycle. Fault relay is active in any fault condition. This relay is failsafe and normally energised if power is removed from the panel the relay will changeover to produce a fault signal. Aux. fire relay is active in an alarm condition provided all relevant delays have expired. Remote relay is active during any Alarm Condition provided all relevant delays have expired. Outputs are NOT designed to switch mains voltages.

GBP 239.96
1

3x C-TEC 12V 2A Encased Switch Mode PSU to EN54-4/A2

3x C-TEC 12V 2A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF560-12 LPCBcertified EN54-4/A2 boxed 12V 2A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole voltfree changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 257.97
1

2x C-TEC 24V 1.5A Encased Switch Mode PSU to EN54-4/A2

2x C-TEC 24V 1.5A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF560-24LPCBcertified EN54-4/A2 boxed 24V 1.5A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole volt-free changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 179.98
1

2x C-TEC 24V 5A Encased Switch Mode PSU to EN54-4/A2

2x C-TEC 24V 5A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF562-5 LPCB/VDS certified EN54-4/A2 boxed 24V 5A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole volt-free changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 259.98
1

2x C-TEC 24V 3A Encased Switch Mode PSU to EN54-4/A2

2x C-TEC 24V 3A Encased Switch Mode PSU to EN54-4/A2

Apowerful switch mode/digital hybrid PSU that can be customised to suit your exact requirements see More Information tab for details. Plasticcoveron PSU PCB guards against touching live parts (to VDE 0100-410). Includes the same electronics as our BF562-3 LPCB/VDS certified EN54-4/A2 boxed 24V 3A PSU. Metal base platefacilitatesstraightforwardmountinginside third-party OEMenclosures. Includes a single-pole volt-free changeover relay that switches for any fault condition. Includes afault type& hazardous voltages present LED. Two selectable battery charge currents. Battery fault impedance limits can be optimised to suit load current (helps extend battery life)*. Mains fail simulation mode. Improved on-board temperature sensor with optional remote sensor. Electronic functions comply with EN50131-6 grades 1-4 for security applications.

GBP 219.98
1

5x C-TEC CAST Mini I/O Unit

5x C-TEC CAST Mini I/O Unit

LPCB certified to EN54-17 & 18 and Kiwa Telefication certified to EN54-13. Includes a switch monitor, signal relay and onboard loop isolator. 7mA typical alarm current (1mA typical quiescent current) @ 22-40V DC. Four plastic tabs for surface or panel mounting. Includes a 1A 30V DC volt-free changeover relay. Can also switch 0.3A @125V AC. Offers Switch +Ve, Ve, LED +V, Ve and changeover relay connections Future header pin offers expansion opportunities for peripheral I/O devices.

GBP 224.95
1

3x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote & 8 Output Per Zone Relays)

3x C-TEC CFP Relay Output Card (Reset, Fault, Aux. & Remote & 8 Output Per Zone Relays)

An optional system expansion device for use with CFP Standard 2-8 Zone Fire PanelsorCFP AlarmSense 2-8 Zone Fire Panels. Provides four panel-controlled volt free relay outputs (reset, fault, aux. fire and remote) and eight output per zone relays. PCB mounts inside the CFP fire panel. Reset relay is active during the panels reset cycle. Fault relay is active in any fault condition. This relay is failsafe and normally energised if power is removed from the panel the relay will changeover to produce a fault signal. Aux. fire relay is active in an alarm condition provided all relevant delays have expired. Remote relay is active during any Alarm Condition provided all relevant delays have expired. Output per zone relays will changeover when the corresponding zone is in alarm (subject to certain conditions for full details refer to the instructions, downloadable below). Outputs are NOT designed to switch mains voltages.

GBP 239.97
1