hands on machine learning from GBP 8 | See the cheapest prices and offers on css.lazzaweb.dk

C-Tec BF375P Unregulated Door Release PSU on Double Gang Plate

C-Tec BF375P Unregulated Door Release PSU on Double Gang PlateA compact mains derived power supply unit designed to provide power to 24V DC electromagnetic door retainers. Trigger Release Hold Off and Local Trigger Inputs facilitate straightforward connection to fire alarm control panels building management systems timers relays and other ancillary equipment.Key FeaturesMaximum output 250mAIncludes a manual release button a Mains on and an Output Triggered indicatorCan be mounted on a standard 25mm UK double gang flush or surface back boxIP Rating IP40

GBP 41.38

1

C-Tec BF366 Isolatable Relay on a Plate 24v 5A

C-Tec BF366 Isolatable Relay on a Plate 24v 5AThe BF366 is a double-pole 24V 5A polarised relay specifically designed for use in 24V fire alarm systems. It includes a key switch isolation facility allowing the relay operation to be temporarily disabled from the fire alarm signal during routine test and maintenance to prevent auto diallers water sprinklers roller shutters etc. from activating.Mountable on a 25mm flush or surface mount back box the relay is trigger able via a control panels open collector output or a standard polarised fire alarm sounder circuit. If connecting to a sounder circuit note that the relay will return to its normal state when the fire condition is cleared or silenced. Check with the approving authority that the proposed arrangement is acceptable prior to installation.Key FeaturesA 24V 5A polarised relay designed for use in 24V fire alarm systemsIncludes a keyswitch isolation facility allowing the relay operation to be temporarily disabled during routine test and maintenance to prevent auto diallers water sprinklers roller shutters etc. from activatingWhen isolated the units Isolated LED will flash and a warning beeper will sound every 8 seconds to ensure devices are not inadvertently left in the isolated stateRelay is triggerable via a control panels open collector output or a standard polarised fire alarm sounder circuit if connecting to a sounder circuit the relay will return to its normal state when the fire condition is cleared or silenced - check with the approving authority that this arrangement is acceptable prior to installationFits on standard UK 25mm flush or surface mount back boxes

GBP 23.32

1

C-Tec BF376 Relay on a Plate 24v 5A Single Gang

BF376 Relay on a Plate 24v 5A Single GangThe BF376 is a general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systems. It incorporates a high intensity LED which illuminates red when the relay is active. It may be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets roller shutter doors etc.Please note if connecting to a sounder circuit the relay will return to its normal state when the fire condition is cleared or silenced. Check with the approving authority that the proposed arrangement is acceptable prior to installation. The relay can be mounted on 25mm flush or surface mount back boxes. Mains wiring if used should be provided in accordance with the current edition of the IEE Wiring Regs.16th.Ed.The general requirement for any mains supply to the BF376 is fixed wiring using three core cable not less than 1mm2 fed from an isolating switch fuse spur fused at 5A max. This should be exclusive to the BF376 and its load and be labelled accordingly. As an alternative to a switched fused spur any double pole isolating device with a contact separation of 3mm or greater which is fitted with suitable in-circuit protection devices and meets the appropriate national wiring regulations can be used.Technical InformationActivation current Typically 30mA 24VDCIndicators Red relay activated LEDConnections V -V Supply NC C NO SW1 SW2. Contact rating 24Vdc is 5A resistive 2A inductive Contact rating 240Vac is 5A resistive 2A inductiveProduct dimensions mm 85w x 85h x 27d mm can be mounted onto a standard UK 25mm single gang flush or surface back boxConstruction finish White PVC plate light grey label silver nickel contactsIP Rating IP40Weight 78gOperating temperature -10C to 60CKey FeaturesA general purpose double-pole polarised 24V 5A relay designed for use in 24V fire alarm systemsIncorporates a high intensity LED which illuminates red when the relay is activeCan be connected to a suitable control panel relay output or a standard polarised fire alarm sounder circuit to operate door retaining magnets rollershutter doors etcCan be mounted on 25mm flush or surface mount back boxes

GBP 8.15

1

C-Tec QT951 Quantec Addressable Accessible Toilet Alarm Kit

C-Tec QT951 Quantec Addressable Accessible Toilet Alarm KitA cost-effective expansion kit that adds true BS8300 compliant accessible toilet alarm functionality to a Quantec Addressable Call System. Includes a QT607 ceiling pull unit a QT605S reset point cw confidence sounder a Quantec slave overdoor light cw sounder and an NC949 Accessible Toilet Sticker.Key FeaturesAllows people in distress to call for help quickly and easily.Call acknowledgement function provides audible visual feedback inside the WC that help is on the way see Operation section below.Staff can Accept alarm calls at a Quantec display.Multiple kits can be used on one Quantec system.Includes a free MRSA resistant anti-bacterial pull cord pack for a limited period only.Backwards compatible.Must be used in conjunction with at least one Quantec Controller.Operating1. The distressed person raises an alarm by pulling the cord on the QT607 Ceiling Pull Unit.Inside the WC The red reassurance LED on the QT607 Ceiling Pull Unit and the reassurance LED and sounder on the QT605S Reset Point cw Sounder pulse Quantecs standard call sequence 0.5 seconds on and 0.5 seconds off to reassure the user the call has been registered.Outside the WC The Alarm LEDs and sounder on the QT606S Overdoor Light cw Sounder pulse Quantecs standard call sequence 0.5 seconds on 0.5 seconds off and a message appears on all relevant Quantec displays as programmed to let staff know someone is in need of assistance.2. The member of staff responding to the Alarm call presses the Call Accept button on a Quantec DisplayInside the WC The reassurance LED and sounder on the QT605S Reset Point cw Sounder pulse Quantecs Call Acknowledged sequence 0.5 seconds on 3 seconds off redgreen to let the user know help is on the way.3. Once assistance has been provided the Alarm call is cancelled from inside the WC by pressing the RESET button on the QT605S Reset Point cw SounderInside and outside the WC All relevant indicators display messages and sounders are extinguished and the calling device returns to its normal state.If the RESET button on the QT605S is NOT pressed when in the call acknowledged state after a period of 1 to 8 minutes as programmed it generates another AlarmStandard call on the system.

GBP 110.95

1

C-Tec NC930 12v 250mA Double Gang PSU

C-Tec NC930 12v 250mA Double Gang PSUThe NC930 is a mains to regulated DC power supply providing 250mA at 13.5V. The green ON indicator indicates that the unit is powered up.Key FeaturesA compact 12V 250mA double gang power supply unitCan provide power to up two NC944 Four Zone Call ControllersSuitable for use in many other applicationsIncludes a green power on indicatorMounts on a standard UK 25mm double gang flush or surface back box

GBP 68.17

1

C-Tec QT616 Quantec InfraredRadio Fall Sensor

C-Tec QT616 Quantec InfraredRadio Fall SensorThe QT616 activates a call on a compatible Quantec infrared or radio receiver when the person wearing it falls or if its button is pressed.10m line-of-sight IR transmitting range. RF coverage dependent on the Quantec receiving device used.Key FeaturesIncludes a Karabiner clip and lanyardCan be programmed to generate different call levels using a QT423 configuratorIdeal for use by the elderly and infirm or security guards and other lone workersCan also be programmed to include a unique User IDname that will appear on the Quantec systemSupplied with a user-replaceable CR2 3V battery offering 6 to 12 months battery life dependent on usage

GBP 148.39

1

C-Tec NC809DB Conventional Button Reset Point

C-Tec NC809DB Conventional Button Reset PointA button-operated reset point for use with C-TECs 800 Series Call System. Can beused toremotely cancel standard calls generated from ceiling pulls andor wall call points that are wired on the same zone. Key FeaturesMounts on a standard UK 25mm single gang flush or surface back box.

GBP 12.08

1

C-Tec XFP501EMCA XFP 1 Loop 16Z Motherboard CAST

C-Tec XFP501EMCA XFP 1 Loop 16Z Motherboard CASTAn XFP 1 Loop 16z Motherboard on the CAST protocol.

GBP 229.12

1

C-Tec XFP501MCA XFP 1 Loop 32Z Motherboard CAST

C-Tec XFP501MCA XFP 1 Loop 32Z Motherboard CASTAn XFP 1 Loop 32z Motherboard on the CAST protocol.

GBP 280.34

1

C-Tec XFP502MCA XFP 2 Loop 32Z Motherboard CAST

C-Tec XFP502MCA XFP 2 Loop 32Z Motherboard CASTAn XFP 2 Loop 32z Motherboard on the CAST protocol.

GBP 352.21

1

C-Tec BF367 Auxiliary Device Isolator single gang

BF367 Auxiliary Device Isolator single gangThe BF367 allows a 24V d.c. output from a fire alarm control panel to be remotely isolated to prevent external equipment such as auto diallers roller shutter doors etc from operating. This is a particularly useful function during routine test and maintenance as it safeguards against the inadvertent and potentially hazardous triggering of auxiliary equipment.To aid location the BF367s front label has a white write on panel allowing installers to add their own personalised text such as equipment locations. The unit will fit on 25mm deep flush or surface mount back boxes.Key FeaturesThe BF367 incorporates an isolating key switch and a high intensity amber LEDThe switch circuit has been designed so that if monitoring is used on the 24V d.c. output being controlled a fault condition will show at the fire panel when the BF367s key switch is in the ISOLATED position note that the key can be removed from the key switch in both the ON and ISOLATED positionsThe units amber LED can also be set-up to illuminate when the key switch is in the ISOLATED position provided sufficient voltage is presentAllows a 24 VDC output from a fire alarm control panel to be remotely isolated to prevent autodiallers water sprinklers rollershutters etc. from activatingDesigned so that if monitoring is used on the 24 VDC output being controlled a fault condition will show at the fire panel when the device is IsolatedLabel includes a white write on area allowing installers to add equipment locationsFits on standard UK 25mm flush or surface mount back boxes

GBP 21.18

1

C-Tec BF319 Fire Alarm Control Panel Mains Key Switch

C-Tec BF319 Fire Alarm Control Panel Mains Key SwitchAhigh-quality lockable double pole Fire Alarm Control Panel Mains key switch. Allows the Mains supply to a fire alarm panelto be switched on or offin accordance with BS 5839-1.Ideal for use during routine test and maintenance e.g. battery test main board replacement etc.Note ifworking on the Mains in the panel you must also follow correct practice and isolate the Mains supply at the distribution board.Key FeaturesFits on a standard UK 47mm flush or surface mount back box.Supplied with 2 x M3.5 25mm fixing screws.BS EN60669-1 compliant.

GBP 17.15

1

C-Tec NC804DE Conventional Emergency Call Reset Point with Button Reset

C-Tec NC804DE Conventional Emergency Call Reset Point with Button ResetA button-operated callresetpoint capable of generating Emergency calls on an 800 Series Call System. Onboard reset button cancels Emergency calls made from the NC804DE and Standard calls made from other devices wired on the same zone such as ceiling pull units in Ensuite areas. Ideal for use as a reset point for ceiling pull units that will allow a more urgent Emergency call to be made if additional assistance is required.Key FeaturesRed reassurance LED confirms a call has been made.Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 36.24

1

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920F

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920FThe NC910EF expands the number of zones on an NC910F or NC920F Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910EF provides 10 extra zones NC920EF provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 185.51

1

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920S

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920SThe NC910ES expands the number of zones on an NC910S or NC920S Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910ES provides 10 extra zones NC920ES provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 191.70

1

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920F

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920FThe NC920EF expands the number of zones on an NC910F or NC920F Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910EF provides 10 extra zones NC920EF provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 222.61

1

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920S

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920SThe NC920ES expands the number of zones on an NC910S or NC920S Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910ES provides 10 extra zones NC920ES provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 228.82

1

C-Tec NC802DB Conventional Call Point with Button Reset and Remote Socket

C-Tec NC802DB Conventional Call Point with Button Reset and Remote SocketAn attractively designed button-operated callreset point capable of generating Standard calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling device.Key FeaturesRed reassurance LED confirms a call has been made.Onboard reset button cancels calls made from the NC802DB and standard calls made from other devices wired on the same zone such as ceiling pull units in en-suite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 27.18

1

C-Tec CA736 EACIE 1 Way Flat Interface - Double Gang

C-Tec CA736 EACIE 1 Way Flat Interface - Double GangA loop-powered single way flat interface for use on a C-TEC EVAC-ALERT system which can control one or more evacuation alert devices located inside a flat.Key FeaturesReliable hard-wired technologyCompatible with the self-test facility on C-TECs BF430EA and BF433CEA range of self-testing evacuation alert devicesProvides one open short circuit fault monitored conventional sounder circuit faults are indicated on the CA736 and reported back to the host EVAC-ALERT panelMounts on a standard UK 35mm double gang back box outside the flat for BS 8629 Clause 8 compliance50mA alarm current can power up to 8 evacuation alert sounders most sites require only one alert sounder so this allows additional alert devices to be connected e.g. for the hard of hearingPolling Sounder Circuit Active and Input Fault indicatorsOn-board short circuit loop isolator

GBP 118.24

1

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote Socket

C-Tec NC802DEB-12 Conventional Emergency Call Point with Button Reset and Remote SocketAn attractively designed button-operated callreset point capable of generating Standard and Emergency calls on an 800 Series Call System. Includes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling device.Key FeaturesRed reassurance LED confirms a call has been madeOnboard reset button cancels Standard and Emergency calls made from the NC802DEB-12 and Standard calls made from other devices wired on the same zone such as ceiling pull units in Ensuite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 43.27

1

C-Tec SPE0849000 NC802DB cw QT602E Label

C-Tec SPE0849000 NC802DB cw QT602E LabelThe SPE0849000 is a NC802DB which comes with a QT602E Label.An attractively designed button-operated callreset point capable of generating Standard calls on an 800 Series Call System.Key FeaturesIncludes a 6.35mm jack plug socket for the connection of an optional tail call lead pressure mat or other ancillary calling deviceRed reassurance LED confirms a call has been madeOnboard reset button cancels calls made from the NC802DB and standard calls made from other devices wired on the same zone such as ceiling pull units in Ensuite areasMounts on a standard UK 25mm single gang flush or surface back box

GBP 25.38

1

C-Tec QT422RXEX Quantec External Extension Aerial

C-Tec QT422RXEX Quantec External Extension AerialOptional external extension aerial QT422RXEX can increase coverage to up to 90m on the QT422RX Quantec Radio Receiver.

GBP 376.08

1

C-Tec NC809DM Conventional Magnetic Reset Point

C-Tec NC809DM Conventional Magnetic Reset PointA magnetic key-operated reset point for use with C-TECs 800 Series Call System. Can beused toremotely and securely cancel standard calls generated from ceiling pulls andor wall call points that are wired on the same zone. Key FeaturesMagnetic reset targetrequires a separately available NC803M magnetic reset key to operateMounts on a standard UK 25mm single gang flush or surface back box

GBP 11.80

1

C-Tec QT615S Quantec Display Interface

C-Tec QT615S Quantec Display InterfaceAllows a QT608CD1S large corridor display to be connected to Quantec via an RS232 serial interface lead supplied with the large display.Key FeaturesMounts on a standardUK 20mm double gang flush or surface back box.The data connection to the large display is monitored. If this is disconnected or the large display is switched off then the QT615S appears as Missing on the Quantec controller.

GBP 105.32

1

C-Tec NC943B Conventional Single Zone Call Controller

C-Tec NC943B Conventional Single Zone Call ControllerThe NC943B is a single zone call controller cw a 12V 140mA PSU and standby battery. The device is fully compatible with C-TECs entire range of 800 Series Call System components.Key FeaturesCapable of indicating standard constant tone and emergency intermittent tone calls.Includes a volume adjustable sounder and a link-selectable Call AcceptReset button.Power on and Alarm CALLING LEDs.Volt-free relay output for the optional connection of externally powered beacons etc relay activates on active call signal.Standby battery provides up to 24 hours standby and 15 minutes alarm running time.Mounts on a standard UK 25mm double gang flush or surface back box.Also available as part of the NC951 Accessible Toilet Alarm Kit.

GBP 106.38

1

Awardvindende Google Marketing Powerhouse

Brand

Merchant

Price (EUR)