35 results (0,14068 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec QT412RXCA Infrared Radio Transmitter Push for Call Pull for Attack

C-Tec QT412RXCA Infrared Radio Transmitter Push for Call Pull for Attack

C-Tec QT412RXCA Infrared Radio Transmitter Push for Call Pull for AttackAllows staff to remotely trigger Attack and Standard calls via a Quantec infrared call point ceiling receiver or radio receiver. Can also be used on 800 Series call systems to trigger Standard and Emergency calls via an800 Series infrared receiving device.Key Features10m line-of-sight IR transmitting range.Radio coverage dependent on the Quantec receiving device used.Includes a Karabiner clip for attaching to staff uniforms.Calls are triggered by pulling the transmitters retaining clip or activating one ofits two buttons.Can be recharged using a QT4241 single-way or QT42410 ten-way charging unit.Can be programmed to generate different call levels using a QT423 configurator.Transmitters used on Quantec systems can also be programmed to includeaunique User IDname.

GBP 115.03
1

C-Tec QT645 Quantec PIR Power Interface with Isolating Key Switch

C-Tec QT645 Quantec PIR Power Interface with Isolating Key Switch

C-Tec QT645 Quantec PIR Power Interface with Isolating Key SwitchAllows up to two QT638 PIR movement sensors to be connected to a Quantec addressable call system. Connects to the slave input on a QT602 or QT609 Range Call Point. Typically located outside a bedroom where for example two PIRs are beingused to monitor a patient getting out of bed. Includes an isolation key switch so staff entering the room can temporarily disable the PIRs from triggering a call.Key FeaturesDerives its power from the Quantec networknoneed for a separate power supply unitA maximum of16 QT645s can be connected to a Quantec system.Mounts on a standard UK 25mm single gang flush or surface back box.

GBP 90.38
1

C-Tec QT412RXA Infrared Radio Transmitter Push for Attack Pull for Attack

C-Tec QT412RXA Infrared Radio Transmitter Push for Attack Pull for Attack

C-Tec QT412RXA Infrared Radio Transmitter Push for Attack Pull for AttackAllows staff working in high-risk environments to remotely trigger an Attack call via a Quantec infrared call point ceiling receiver or radio receiver. Can also be used on 800 Series call systems to trigger Standard and Emergency calls via an800 Series infrared receiving device.Key Features10m line-of-sight IR transmitting range.Radio coverage dependent on the Quantec receiving device used.Includes a Karabiner clip for attaching to staff uniforms.Calls are triggered by pulling the transmitters retaining clip or activating one ofits two buttons.Can be recharged using a QT4241 single-way or QT42410 ten-way charging unit.Can be programmed to generate different call levels using a QT423 configurator.Transmitters used on Quantec systems can also be programmed to includeaunique User IDname.

GBP 115.03
1

C-Tec BF560-24 Switch Mode 24v 1.5A EN54-4 Boxed PSU

C-Tec BF560-24 Switch Mode 24v 1.5A EN54-4 Boxed PSU

C-Tec BF560-24 Switch Mode 24v 1.5A EN54-4 Boxed PSUThe BF560-24 is certified to EN54-4A2 by the LPCB and VdS AFNOR pending. It features a plastic cover on PSU PCB which guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition.Key FeaturesMultiple indicators - supply present general fault fault type aux. equipment fault.Two selectable battery charge currents.Battery fault impedance limits can be optimised to suit load current helps extend battery life.Mains fail simulation mode.Improved on-board temperature sensor with optional remote sensor.Electronic functions comply with EN50131-6 grades 1-4 for security applications.BF560-24E caged BF560-24C PCB-only versions available.

GBP 123.43
1

C-Tec BF562-1 Switch Mode 24v 1.5A EN54-4 Boxed Metal PSU

C-Tec BF562-1 Switch Mode 24v 1.5A EN54-4 Boxed Metal PSU

C-Tec BF562-1 Switch Mode 24v 1.5A EN54-4 Boxed Metal PSUThe BF562-1 is certified to EN54-4A2 by the LPCB and VdS AFNOR pending. It comes with a plastic cover on PSU PCB which guards against touching live parts. Includes a single-pole voltfree changeover relay that switches for any fault condition.Key FeaturesMultiple indicators - supply present general fault fault type aux. equipment faultTwo selectable battery charge currentsBattery fault impedance limits can be optimised to suit load current helps extend battery lifeMains fail simulation modeImproved on-board temperature sensor with optional remote sensorElectronic functions comply with EN50131-6 grades 1-4 for security applicationsBF562-1E caged BF562-1C PCB-only versions availableTYPICAL USESIdeal for poweringbeam detectors auto-dial communicators aspirating smoke detectors auto-open vent systems auxiliary sounder systems or any other device performing a mandatory function of a fire alarm system.PSU CUSTOMISATIONThe BF562-1can be customised to suit your exact requirements using a BF423 configurator PC. Configurable parameters include float voltage temperature compensation battery charge rate mA battery impedance and configurableInputOutput settings. It is important to note changing the PSUs parameters in this way isoutside the scope of EN54-4 and any changes mustbe tested by the responsible person for correctoperation.PSU STATUS LEDlocated on the PSU PCB1 flash Mains Failure.2 flashes Battery Voltage Low.3 flashes Battery Voltage Critical.4 flashes Charger Failure.5 flashes Charger OK Battery is either actively charging or in float charge.6 flashes No Batteries Fitted indicating DIP Switch 4 position.7 flashes Battery Resistance Fault Level set by DIP Switch 2 position.8flashes Output Over Voltage.BATTERY FAULT MONITORINGThe BF562-1 complies with EN54-4A2 and therefore must monitor battery resistance. The fault threshold is directly related to the ability of the battery to deliver the rated current to the load. For example batteries stored uncharged for long periods during shipment andor distribution degrade leading to increased internal resistance. If a degraded battery is fitted a fault will be shown by the PSU as mandated by EN54-4A2.DATA PORTData on the BF562-1s status can be extracted from the PSUsbi-directional data port. The data availableincludes thermistor measurements battery terminal voltage system voltage at load terminals battery charge current load current battery impedanceandASCII text string status messages. Extracting this data requires additional equipment and permissions - contact C-TEC for details.

GBP 155.72
1

C-Tec BF560-12 Switch Mode 12v 2A EN54-4 Boxed PSU

C-Tec BF560-12 Switch Mode 12v 2A EN54-4 Boxed PSU

C-Tec BF560-12 Switch Mode 12v 2A EN54-4 Boxed PSUThe C-Tec BF560-12 12V 2A EN54-4 Switch Mode PSU is ideal for connecting to 12V security STUs to provide BS5839-1 compliant remote monitoring facilities. It is certified to EN54-4A2 by the LPCB VdS AFNOR pending.Key FeaturesMultiple indicators - supply present general fault fault type aux. equipment fault.Two selectable battery charge currents.Battery fault impedance limits can be optimised to suit load current helps extend battery life.Mains fail simulation mode.Improved on-board temperature sensor with optional remote sensor.Ideal for connecting to 12V security STUs to provide BS5839-1 compliant remote monitoring facilities.Electronic functions comply with EN50131-6 grades 1-4 for security applications.BF560-12E Caged BF560-12C PCB-only versions available.Plastic cover on PSU PCB guards against touching live parts.Includes a single-pole voltfree changeover relay that switches for any fault condition.Additional InformationPSU CUSTOMISATIONThe BF560-12can be customised to suit your exact requirements using a BF423 configurator PC. Configurable parameters include float voltage temperature compensation battery charge rate mA battery impedance and configurableInputOutput settings. It is important to note changing the PSUs parameters in this way isoutside the scope of EN54-4 and any changes mustbe tested by the responsible person for correctoperation.12V SECURITY STUUSED PURELY FOR FIRE ALARM SIGNALLINGThe BF560-12 can help combat an area of fire alarm system non-compliance that is often overlooked - their connection to remote monitoring centres via 12V security STUs or autodiallers. Firesystems that require such monitoring are typically connected to 12V security STUs. Unfortunately PSUs used to power these STUs normally only offer 12 hours standby are notconnected to a dedicated mains supply and do not include the features demanded by EN54-4 such as battery impedance monitoring temperature compensated charging CPR compliance etc. TheBF560-12 solves these problems by allowing the use of 12V STUs with a cost-effective EN54-4 compliant PSU thereby facilitating compliance with BS5839-1 or European equivalents. Tofurther assist this application an optional STU mounting plate is available for inside the BF560-12 order code BF360SP.PSU STATUS LEDlocated on the PSU PCB1 flash Mains Failure.2 flashes Battery Voltage Low.3 flashes Battery Voltage Critical.4 flashes Charger Failure.5 flashes Charger OK Battery is either actively charging or in float charge.6 flashes No Batteries Fitted indicating DIP Switch 4 position.7 flashes Battery Resistance Fault Level set by DIP Switch 2 position.8flashes Output Over Voltage.BATTERY FAULT MONITORINGThe BF560-12 complies with EN54-4A2 and therefore must monitor battery resistance. The fault threshold is directly related to the ability of the battery to deliver the rated current to the load. For example batteries stored uncharged for long periods during shipment andor distribution degrade leading to increased internal resistance. If a degraded battery is fitted a fault will be shown by the PSU as mandated by EN54-4A2.EN50131-6 POWER SUPPLIES FOR INTRUSION HOLD UP ALARMS CAPABILITYThe power supply inside the BF560-12 has all the electrical functions required to comply with EN50131-6 Grade 4which includes Grades 3 2 and 1. However the BF560-12s enclosure isnot designed to comply with the standardsrequirements totriggeranalarm if someone tries to force the box open. OEM security companies interested in utilising the BF560-12s PSUPCB inside their own EN50131-6 compliant tamper-resistant enclosures should contact our marketing departmentfor further detailson costs and approvals.DATA PORTData on the BF560-12s status can be extracted from the PSUsbi-directional data port. The data availableincludes thermistor measurements battery terminal voltage system voltage at load terminals battery charge current load current battery impedanceandASCII text string status messages. Extracting this data requires additional equipment and permissions -call C-TEC for details.

GBP 113.64
1

C-Tec 24V 3A EN54-4 Switch Mode PSU BF562-3

C-Tec 24V 3A EN54-4 Switch Mode PSU BF562-3

C-Tec 24V 3A EN54-4 Switch Mode PSU BF562-3Ideal for powering beam detectors auto-dial communicators aspirating smoke detectors auto-open vent systems auxiliary sounder systems or any other device performing a mandatory function of a fire alarm system.Key FeaturesVDS certified to EN54-4 1997A22006.Ideal for poweringbeam detectors auto-dial communicators aspirating smoke detectors auto-open vent systems auxiliary sounder systems or any other device performing a mandatory function of a fire alarm system.Deep discharge battery protection and EN54 compliant reporting of battery impedance faults.Includes a single-pole volt-free changeover relay that switches for any fault condition.Three LED indicators - supply present general fault and auxiliary fault for optional connection to third-party equipment.Link selectable battery charging capacity.Environmentally-friendly charging circuit - dissipates just 0.35W compared to the industry norm of 2.55W.Supplied in a tough durable metal box.Optional caged and PCB-only versions available with exactly the same electronics order code BF362-3E and BF362-3C respectively.

GBP 163.93
1

C-Tec NC805AS Air Switch

C-Tec NC805AS Air Switch

C-Tec NC805AS Air SwitchThe NC805AS is designed for use with C-TECsNC805P Pneumatic Pad. Applying pressure to the NC805P operates the airswitch which in turn triggers a Standard call when the 6.35mm jack plug on the NC805ASis connected to a compatible call points remote socket.Key FeaturesOperates at a minimum differential air pressure of 0.9 p.s.i pounds per square inch or 6220 Pa pascals 10 at 16CIP Rating IP20Ideal for patients who find it difficult to press buttons

GBP 106.18
1

C-Tec QT616 Quantec InfraredRadio Fall Sensor

C-Tec QT616 Quantec InfraredRadio Fall Sensor

C-Tec QT616 Quantec InfraredRadio Fall SensorThe QT616 activates a call on a compatible Quantec infrared or radio receiver when the person wearing it falls or if its button is pressed.10m line-of-sight IR transmitting range. RF coverage dependent on the Quantec receiving device used.Key FeaturesIncludes a Karabiner clip and lanyardCan be programmed to generate different call levels using a QT423 configuratorIdeal for use by the elderly and infirm or security guards and other lone workersCan also be programmed to include a unique User IDname that will appear on the Quantec systemSupplied with a user-replaceable CR2 3V battery offering 6 to 12 months battery life dependent on usage

GBP 148.39
1

C-Tec CP411T CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder

C-Tec CP411T CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder

C-Tec CP411T CAST-PRO CO Fire Smoke Heat Multisensor cw Tone SounderA programmable CAST-PRO CO fire smoke heat multisensorfire detector which is certified to EN54-5 7 17 29 31. It is compatiblewith C-TECs ZFP touchscreen-controlled CAST protocol addressable fire panel.MASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditions.Key FeaturesDrift compensation functionalityOnboard short circuit loop isolatorIncludes two 8mm x 2mm ultra-bright red LED indicatingstripsMultiple detection modes and different sensitivities fordifferent times of the day1mA alarm current max vol VAD on630uA typical quiescent current 40V DCCompatible with C-TECs CA408 CAST base cw integratedlocking mechanism ID tagComes with Tone Sounder

GBP 99.79
1

C-Tec CP414V CAST-PRO Smoke Heat Multisensor cw Voice Sounder

C-Tec CP414V CAST-PRO Smoke Heat Multisensor cw Voice Sounder

C-Tec CP414V CAST-PRO Smoke Heat Multisensor cw VoiceSounderA multiple functionality in a single device smoke heat multisensor fire detection plus an 86dbA voice sounder detects realfires quickly reduces false alarms effectively and indicates true alarmconditions decisively.Key FeaturesCertified to EN54-3 5 7 17 29.Compatible with C-TECs ZFPtouchscreen-controlled CAST protocol addressable fire panel.MASC Miniature Advanced Smoke DetectionChamber and AFFIRM algorithms provide incredible tolerance to false alarmswhilst enhancing the detection of real fire conditions.Drift compensation functionality.Onboard short circuit loop isolator.Includes two 8mm x 2mm ultra-bright red LEDindicating strips.Multiple detection modes and differentsensitivities for different times of the day.Six selectable voice messages with tones 2evacuate 1 alert 1 all clear 2 system test messages.17.1mA max. alarm current max vol VAD on.590uA typical quiescent current 40V DC.Compatible with C-TECs CA408 CAST base cwintegrated locking mechanism ID tag.

GBP 110.68
1

C-Tec CP414TVR CAST-PRO Smoke Heat Multisensor cw Tone Sounder amp O-C-1.9-4 Red VAD

C-Tec CP414TVR CAST-PRO Smoke Heat Multisensor cw Tone Sounder amp O-C-1.9-4 Red VAD

C-Tec CP414TVR CAST-PRO Smoke Heat Multisensor cw ToneSounder O-C-1.9-4 Red VADMultiple functionality in a single device smoke heatmultisensor fire detection plus a 92dbA tone Alarm sounder and an O-C-1.9-4red VAD detects real fires quickly reduces false alarms effectively andindicates true alarm conditions decisively.Key FeaturesCertified to EN54-3 5 7 17 23 29.Compatible with C-TECs ZFP touchscreen-controlled CASTprotocol addressable fire panel.MASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditions.Drift compensation functionality.Onboard short circuit loop isolator.Includes two 8mm x 2mm ultra-bright red LED indicatingstrips.Multiple detection modes and different sensitivities fordifferent times of the day.13.2mA max. alarm current max vol VAD on.590uA typical quiescent current 40V DC.Compatible with C-TECs CA408 CAST base cwintegrated locking mechanism ID tag.

GBP 133.36
1

C-Tec CP411TV CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder amp C-3-9.4 White VAD

C-Tec CP411TV CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder amp C-3-9.4 White VAD

C-Tec CP411TV CAST-PRO CO Fire Smoke Heat Multisensorcw Tone Sounder C-3-9.4 White VADA multiple functionality in a single device CO fire heat smoke multisensor fire detection plus a 92dbA tone Alarm sounder and aC-3-9.4 VAD detects real fires quickly reduces false alarms effectively andindicates true alarm conditions decisively.Key FeaturesCertified to EN54-3 5 7 17 23 29 31Compatible with C-TECs ZFP touchscreen-controlled CASTprotocol addressable fire panelMASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditionsDrift compensation functionalityOnboard short circuit loop isolatorIncludes two 8mm x 2mm ultra-bright red LED indicatingstripsMultiple detection modes and different sensitivities fordifferent times of the day13.2mA max. alarm current max vol VAD on630uA typical quiescent current 22-40V DCCompatible with C-TECs CA408 CAST base cw integratedlocking mechanism ID tag

GBP 149.69
1

C-Tec CP414TV CAST-PRO Smoke Heat Multisensor cw Tone Sounder amp C-3-9.4 White VAD

C-Tec CP414TV CAST-PRO Smoke Heat Multisensor cw Tone Sounder amp C-3-9.4 White VAD

C-Tec CP414TV CAST-PRO Smoke Heat Multisensor cw ToneSounder C-3-9.4 White VADMultiple functionality in a single device smoke heatmultisensor fire detection plus a 92dbA tone Alarm sounder and a C-3-9.4 VAD detects real fires quickly reduces false alarms effectively and indicatestrue alarm conditions decisively.Key FeaturesCertified to EN54-3 5 7 17 23 29.Compatible with C-TECs ZFP touchscreen-controlled CASTprotocol addressable fire panel.MASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditions.Drift compensation functionality.Onboard short circuit loop isolator.Includes two 8mm x 2mm ultra-bright red LED indicatingstrips.Multiple detection modes and different sensitivities fordifferent times of the day.13.2mA max. alarm current max vol VAD on.590uA typical quiescent current 40V DC.Compatible with C-TECs CA408 CAST base cwintegrated locking mechanism ID tag.

GBP 112.94
1

C-Tec CP411TVR CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder amp O-C-1.9-4 Red VAD

C-Tec CP411TVR CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder amp O-C-1.9-4 Red VAD

C-Tec CP411TVR CAST-PRO CO Fire Smoke Heat Multisensor cw Tone Sounder O-C-1.9-4 Red VADA multiple functionality in a single device CO fire heat smoke multisensor fire detection plus a 92dbA tone Alarm sounder and aO-C-1.9-4 red VAD detects real fires quickly reduces false alarms effectively andindicates true alarm conditions decisively.Key FeaturesCertified to EN54-3 5 7 17 23 29 31Compatible with C-TECs ZFP touchscreen-controlled CASTprotocol addressable fire panelMASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditionsDrift compensation functionalityOnboard short circuit loop isolatorIncludes two 8mm x 2mm ultra-bright red LED indicatingstripsMultiple detection modes and different sensitivities fordifferent times of the day13.2mA max. alarm current max vol VAD on630uA typical quiescent current 22-40V DCCompatible with C-TECs CA408 CAST base cw integratedlocking mechanism ID tag

GBP 158.76
1

C-Tec CP411V CAST-PRO CO Fire Smoke Heat Multisensor cw Voice Sounder

C-Tec CP411V CAST-PRO CO Fire Smoke Heat Multisensor cw Voice Sounder

C-Tec CP411V CAST-PRO CO Fire Smoke Heat Multisensor cwVoice SounderMultiple functionality in a single device CO fire smoke heat multisensor fire detection plus an 86dbA voice sounder detectsreal fires quickly reduces false alarms effectively and indicates true alarmconditions decisively. It is certified to EN54-3 5 7 17 29 31.Compatible with C-TECs ZFP touchscreen-controlled CASTprotocol addressable fire panel.Key FeaturesMASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditionsDrift compensation functionalityOnboard short circuit loop isolatorIncludes two 8mm x 2mm ultra-bright red LED indicatingstripsMultiple detection modes and different sensitivities fordifferent times of the daySix selectable voice messages with tones 2 evacuate 1alert 1 all clear 2 system test messages17.1mA max. alarm current max vol VAD on630uA typical quiescent current 40V DCCompatible with C-TECs CA408 CAST base cw integratedlocking mechanism ID tag

GBP 136.08
1

C-Tec CP414VVR CAST-PRO Smoke Heat Multisensor cw Voice Sounder amp O-C-1.9-4 Red VAD

C-Tec CP414VVR CAST-PRO Smoke Heat Multisensor cw Voice Sounder amp O-C-1.9-4 Red VAD

C-Tec CP414VVR CAST-PRO Smoke Heat Multisensor cw VoiceSounder O-C-1.9-4 Red VADA multiple functionality in a single device smoke heat multisensor fire detection plus an 86dbA voice sounder and an O-C-1.9-4red VAD detects real fires quickly reduces false alarms effectively andindicates true alarm conditions decisively.Key FeaturesCertified to EN54-3 5 7 17 23 29.Compatible with C-TECs ZFP touchscreen-controlled CASTprotocol addressable fire panel.MASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditions.Drift compensation functionality.Onboard short circuit loop isolator.Includes two 8mm x 2mm ultra-bright red LED indicatingstrips.Multiple detection modes and different sensitivities fordifferent times of the day.Six selectable voice messages with tones 2 evacuate 1alert 1 all clear 2 system test messages.24.9mA max. alarm current max vol VAD on.590uA typical quiescent current 40V DC.Compatible with C-TECs CA408 CAST base cw integratedlocking mechanism ID tag.

GBP 169.64
1

C-Tec CP414VV CAST-PRO Smoke Heat Multisensor cw Voice Sounder amp C-3-9.4 White VAD

C-Tec CP414VV CAST-PRO Smoke Heat Multisensor cw Voice Sounder amp C-3-9.4 White VAD

C-Tec CP414VV CAST-PRO Smoke Heat Multisensor cw VoiceSounder C-3-9.4 White VADA multiple functionality in a single device smoke heat multisensor fire detection plus an 86dbA voice sounder and a C-3-9.4 VAD detects real fires quickly reduces false alarms effectively and indicatestrue alarm conditions decisively.Key FeaturesCertified to EN54-3 5 7 17 23 29.Compatible with C-TECs ZFP touchscreen-controlled CASTprotocol addressable fire panel.MASC Miniature Advanced Smoke Detection Chamber andAFFIRM algorithms provide incredible tolerance to false alarms whilstenhancing the detection of real fire conditions.Drift compensation functionality.Onboard short circuit loop isolator.Includes two 8mm x 2mm ultra-bright red LED indicatingstrips.Multiple detection modes and different sensitivities fordifferent times of the day.Six selectable voice messages with tones 2 evacuate 1alert 1 all clear 2 system test messages.24.9mA max. alarm current max vol VAD on.590uA typical quiescent current 40V DC.Compatible with C-TECs CA408 CAST base cwintegrated locking mechanism ID tag.

GBP 160.57
1

C-Tec CFP702-4 2 Zone Conventional Fire Panel LPCB Approved

C-Tec CFP702-4 2 Zone Conventional Fire Panel LPCB Approved

C-Tec CFP 2 Zone Conventional Fire Panel LPCB Approved - CFP702-4LPCB certified to EN54-24 C-TECs CFP 2 zone conventional fire alarm panel offers an array of user and installer-friendly features at a very competitive price. Supplied in an attractive flush or surface mountable plastic enclosure it includes two detector zones four conventional sounder circuits class change and alert inputs on-board fire and fault relays and combined keypadkey switch entry.A wide range of engineering functions are also provided including selectable zone delays coincidence and non-latching zone facilities. Comprehensive test and fault finding facilities are also provided. Optional repeaters relay expansion boards and EN54-13 system compliance devices are also available.Key FeaturesThird-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board LPCB with optional EN54 part 13 compliance from the BSI.Intuitive user-friendly interface with colour-coded buttons and combined keypadkeyswitch entry.Manufactured by C-TEC in the UK.Two detector zone circuits.Four conventional sounder circuitsIntegral 1.5A EN54-4A2 compliant switch mode PSU.Wide range of engineering functions including zone test coincidence zone delay and non-latching zones.Two on-board relays Fire and Fault.Two open-collector outputs Remote and Reset.Class change and alert inputs.Installer-friendly design.Attractive flush or surface mountable plastic lid and enclosure - no bezel required.Low 25mA quiescent current.Multiple indicators.System expansion connections provided for up to eight two-wire repeaters one CFP761 network card required per system optional CFP relay boards and optional EN54-13 compliant sounder circuit boards.Space for two x 12V 3.3Ah VRLA batteries.Fully compatible with C-TECs ActiV range of conventional fire detectors.

GBP 130.25
1

C-Tec CFP 4 Zone Conventional Fire Panel LPCB Approved - CFP704-4

C-Tec CFP 4 Zone Conventional Fire Panel LPCB Approved - CFP704-4

C-Tec CFP 4 Zone Conventional Fire Panel LPCB Approved - CFP704-4LPCB certified to EN54-24 C-TECs CFP 4 zone conventional fire alarm panel offers an array of user and installer-friendly features at a very competitive price. Supplied in an attractive flush or surface mountable plastic enclosure it includes two detector zones four conventional sounder circuits class change and alert inputs on-board fire and fault relays and combined keypadkey switch entry.A wide range of engineering functions are also provided including selectable zone delays coincidence and non-latching zone facilities. Comprehensive test and fault finding facilities are also provided. Optional repeaters relay expansion boards and EN54-13 system compliance devices are also available.Key FeaturesThird-party certified to EN54 parts 2 and 4 by the Loss Prevention Certification Board LPCB with optional EN54 part 13 compliance from the BSI.Intuitive user-friendly interface with colour-coded buttons and combined keypadkeyswitch entry.Manufactured by C-TEC in the UK.Two detector zone circuits.Four conventional sounder circuitsIntegral 1.5A EN54-4A2 compliant switch mode PSU.Wide range of engineering functions including zone test coincidence zone delay and non-latching zones.Two on-board relays Fire and Fault.Two open-collector outputs Remote and Reset.Class change and alert inputs.Installer-friendly design.Attractive flush or surface mountable plastic lid and enclosure - no bezel required.Low 25mA quiescent current.Multiple indicators.System expansion connections provided for up to eight two-wire repeaters one CFP761 network card required per system optional CFP relay boards and optional EN54-13 compliant sounder circuit boards.Space for two x 12V 3.3Ah VRLA batteries.Fully compatible with C-TECs ActiV range of conventional fire detectors.

GBP 148.46
1

C-Tec Output Expansion Relay Board EP212

C-Tec Output Expansion Relay Board EP212

C-Tec Output Expansion Relay Board EP212The EP212 is an optional system expansion device for use withthe EP203 three zone automatic extinguisher panel. Mounts inside the EP203panel to provide five volt free relay contacts reset mode discharged hold and abort.Key FeaturesReset relay switchesduring the panels reset cycleModerelay switcheswhen the extinguishant systems mode is changed to manualDischarged relay switcheswhen a released flow switch input e.g. from theextinguishant pipework is received toindicate the extinguishant has been releasedHoldrelay switcheswhen a hold input isreceived at the panel. If the panel is in 2nd stage alarm i.e. it is in automatic mode and detection circuits are activated or it is in either automaticmanual mode and a manual release input is operated the extinguishant release sequence is haltedAbortrelay switcheswhen an abort input isreceived at the paneltocancel the extinguishant release sequence

GBP 108.35
1