19 results (0,13211 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec NC944SS Four Zone Call Controller in Stainless Steel

C-Tec NC944SS Four Zone Call Controller in Stainless Steel

C-Tec NC944SS Four Zone Call Controller in Stainless SteelThe NC944SS is an attractively-designed four zone call controller which comes with mute and reset buttons.Key FeaturesFully compatible with C-TECs entire range of 800 Series Call System componentsCapable of indicating standard constant tone and emergency intermittent tone callsRequires a separate NC930 12V 250mA PSUIncludes four zonal alarm LEDs RESET and MUTE buttonsTwo open collector outputs Emergency and Aux OutUp to two NC944s can be connected to one NC930 PSU to create a mini-call system of up to 8 zonesMounts on a standard 25mm UK double gang back boxPlease note The image is for illustrative purposes only

GBP 235.82
1

C-Tec QT601-2 Quantec Controller

C-Tec QT601-2 Quantec Controller

C-Tec QT601-2 Quantec ControllerQuantec is a powerful yet easy to use addressable call system that helps ensure vital communication throughout a building. In environments where efficiency is paramount Quantec delivers helping save staff time minimising disturbance and improving the quality of patient customer or employee care. Whatever the application - be it a call system for a nursing home hospital hotel or leisure centre or a staff protection system for a high dependency unit prison factory shop school or council office - Quantec is the obvious choice.With its flexible call routing multiple call levels a unique data protocol that works down just two wires and a laptop programmable system controller Quantec can be tailored to suit the exact operational needs of any building. For example calls can be routed to different parts of a site at different times of the day and unanswered calls can be set to transfer to other areas after a pre-determined time. As well as a huge range of cost-effective call points ceiling pulls displays monitoring points sounders neck pendants and infrared transmitters the system includes a host of industry-leading features.The controller supplies power to and controls a Quantec Addressable Call System. Monitors all network devices and manages the routing and distribution of all calls. Provides connections for network wiring standby batteries a laptop for system programmingoptionalpagingDECT equipment anoptionalprinter orPC to run Quantecs QT707S Surveyor data management software.Key FeaturesIncludes a library of 40 pre-set 45 custom place names.System setup requires a laptop PC running Quantecs QT707 programming tools.Can be semi-flush mounted using an QT385 bezel or fully-flushed using a BF3593S stainless steel enclosure.System wiring requires one or more QT603 network splitters.Wiring should be made in a spine and limb arrangement using 1.5 to 2.5mm2 TE spines and 4 to 8 core stranded security cable limbs.

GBP 426.65
1

C-Tec NC910F Conventional 10 Zone Flush Master Call Controller

C-Tec NC910F Conventional 10 Zone Flush Master Call Controller

C-Tec NC910F Conventional 10 Zone Flush Master Call ControllerThe NC910FCall Controller is compatible with all 800 Series call points ceiling pulls infrared ceiling receivers monitoring points overdoor lights and remote sounders.Depending on how the Controller is configured and the devices connected to it Standard and Emergency calls can be indicated via its buzzer and zonal LEDs. Two buttons A and B are also provided to allow the user to Reset Mute or Accept standard calls as detailed below.Standard Calls when triggered by a calling device the Controllers internal buzzer sounds continuously and the relevant zone indicators illuminate steady.Pressing the Controllers Reset Button A if enabled cancels all standard calls.Pressing the Controllers Mute Button B if enabled silences the Controllers internal buzzer. However if a new call standard or emergency is triggered anywhere on the system the buzzer will resound.Alternatively instead of muting calls Button B can be configured as a CALL ACCEPT button.Pressing Call Accept sends a slow pulsing acknowledgement signal to overdoor lights and reset points cw sounders provided they are wired as shown on the example wiring diagram below. Should a new call standard or emergency be triggered anywhere on the system any zones in the acknowledgement state will revert to a standard call.Emergency Calls when triggered by a calling device the Controllers internal buzzer pulses and the relevant zone indicators flash. This level of call takes priority over standard calls and cannot be muted accepted or reset at the Controller. An emergency call can only be reset at the device from which it was triggered or via a reset point wired on the same zone.Key FeaturesCompatible with C-TECs entire range of 800 Series field devicesHoused in an attractive flush mounting plastic enclosure measuring just 214mm x 178mmTwo call levels - standard constant tone and emergency intermittent toneOptional mute and call acceptreset buttonsCall Accept functionality allows staff to send an intermittent call acknowledgment signal to calling zones to confirm help is on the way dependent on wiring and field devices usedIncludes a 12V 300mA PSU and 2 volt-free relay contacts which activate on a standard or emergency callInnovative slide-in labelling systemZones can be wired in 4 or 6 core 702 stranded security cableAdditional master controllers and expansion units available for use as repeaters on larger sitesOptional boxed PSUs cw with space for a 12V VRLA battery available for sites where a standby battery facility is required

GBP 228.82
1

C-Tec NC920F Conventional 20 Zone Flush Master Call Controller

C-Tec NC920F Conventional 20 Zone Flush Master Call Controller

C-Tec NC920F Conventional 20 Zone Flush Master Call ControllerThe NC920FCall Controller is compatible with all 800 Series call points ceiling pulls infrared ceiling receivers monitoring points overdoor lights and remote sounders.Depending on how the Controller is configured and the devices connected to it Standard and Emergency calls can be indicated via its buzzer and zonal LEDs. Two buttons A and B are also provided to allow the user to Reset Mute or Accept standard calls as detailed below.Standard Calls when triggered by a calling device the Controllers internal buzzer sounds continuously and the relevant zone indicators illuminate steady.Pressing the Controllers Reset Button A if enabled cancels all standard calls.Pressing the Controllers Mute Button B if enabled silences the Controllers internal buzzer. However if a new call standard or emergency is triggered anywhere on the system the buzzer will resound.Alternatively instead of muting calls Button B can be configured as a CALL ACCEPT button.Pressing Call Accept sends a slow pulsing acknowledgement signal to overdoor lights and reset points cw sounders provided they are wired as shown on the example wiring diagram below. Should a new call standard or emergency be triggered anywhere on the system any zones in the acknowledgement state will revert to a standard call.Emergency Calls when triggered by a calling device the Controllers internal buzzer pulses and the relevant zone indicators flash. This level of call takes priority over standard calls and cannot be muted accepted or reset at the Controller. An emergency call can only be reset at the device from which it was triggered or via a reset point wired on the same zone.Key FeaturesCompatible with C-TECs entire range of 800 Series field devicesHoused in an attractive flush mounting plastic enclosure measuring just 214mm x 178mmTwo call levels - standard constant tone and emergency intermittent toneOptional mute and call acceptreset buttonsCall Accept functionality allows staff to send an intermittent call acknowledgment signal to calling zones to confirm help is on the way dependent on wiring and field devices usedIncludes a 12V 300mA PSU and 2 volt-free relay contacts which activate on a standard or emergency callInnovative slide-in labelling systemZones can be wired in 4 or 6 core 702 stranded security cableAdditional master controllers and expansion units available for use as repeaters on larger sitesOptional boxed PSUs cw with space for a 12V VRLA battery available for sites where a standby battery facility is required

GBP 309.20
1

C-Tec NC920S Conventional 20 Zone Surface Master Call Controller

C-Tec NC920S Conventional 20 Zone Surface Master Call Controller

C-Tec NC920S Conventional 20 Zone Surface Master Call ControllerThe NC920S Call Controller is compatible with all 800 Series call points ceiling pulls infrared ceiling receivers monitoring points overdoor lights and remote sounders.Depending on how the Controller is configured and the devices connected to it Standard and Emergency calls can be indicated via its buzzer and zonal LEDs. Two buttons A and B are also provided to allow the user to Reset Mute or Accept standard calls as detailed below.Standard Calls when triggered by a calling device the Controllers internal buzzer sounds continuously and the relevant zone indicators illuminate steady.Pressing the Controllers Reset Button A if enabled cancels all standard calls.Pressing the Controllers Mute Button B if enabled silences the Controllers internal buzzer. However if a new call standard or emergency is triggered anywhere on the system the buzzer will resound.Alternatively instead of muting calls Button B can be configured as a CALL ACCEPT button.Pressing Call Accept sends a slow pulsing acknowledgement signal to overdoor lights and reset points cw sounders provided they are wired as shown on the example wiring diagram below. Should a new call standard or emergency be triggered anywhere on the system any zones in the acknowledgement state will revert to a standard call.Emergency Calls when triggered by a calling device the Controllers internal buzzer pulses and the relevant zone indicators flash. This level of call takes priority over standard calls and cannot be muted accepted or reset at the Controller. An emergency call can only be reset at the device from which it was triggered or via a reset point wired on the same zone.Key FeaturesCompatible with C-TECs entire range of 800 Series field devicesHoused in an attractive surface mounting plastic enclosure measuring just 214mm x 178mmTwo call levels - standard constant tone and emergency intermittent toneOptional mute and call acceptreset buttonsCall Accept functionality allows staff to send an intermittent call acknowledgment signal to calling zones to confirm help is on the way dependent on wiring and field devices usedIncludes a 12V 300mA PSU and 2 volt-free relay contacts which activate on a standard or emergency callInnovative slide-in labelling systemZones can be wired in 4 or 6 core 702 stranded security cableAdditional master controllers and expansion units available for use as repeaters on larger sitesOptional boxed PSUs cw with space for a 12V VRLA battery available for sites where a standby battery facility is required

GBP 315.38
1

C-Tec NC910S Conventional 10 Zone Surface Master Call Controller

C-Tec NC910S Conventional 10 Zone Surface Master Call Controller

C-Tec NC910S Conventional 10 Zone Surface Master Call ControllerThe NC910S Call Controller is compatible with all 800 Series call points ceiling pulls infrared ceiling receivers monitoring points overdoor lights and remote sounders.Depending on how the Controller is configured and the devices connected to it Standard and Emergency calls can be indicated via its buzzer and zonal LEDs. Two buttons A and B are also provided to allow the user to Reset Mute or Accept standard calls as detailed below.Standard Calls when triggered by a calling device the Controllers internal buzzer sounds continuously and the relevant zone indicators illuminate steady.Pressing the Controllers Reset Button A if enabled cancels all standard calls.Pressing the Controllers Mute Button B if enabled silences the Controllers internal buzzer. However if a new call standard or emergency is triggered anywhere on the system the buzzer will resound.Alternatively instead of muting calls Button B can be configured as a CALL ACCEPT button.Pressing Call Accept sends a slow pulsing acknowledgement signal to overdoor lights and reset points cw sounders provided they are wired as shown on the example wiring diagram below. Should a new call standard or emergency be triggered anywhere on the system any zones in the acknowledgement state will revert to a standard call.Emergency Calls when triggered by a calling device the Controllers internal buzzer pulses and the relevant zone indicators flash. This level of call takes priority over standard calls and cannot be muted accepted or reset at the Controller. An emergency call can only be reset at the device from which it was triggered or via a reset point wired on the same zone.Key FeaturesCompatible with C-TECs entire range of 800 Series field devicesHoused in an attractive surface mounting plastic enclosure measuring just 214mm x 178mmTwo call levels - standard constant tone and emergency intermittent toneOptional mute and call acceptreset buttonsCall Accept functionality allows staff to send an intermittent call acknowledgment signal to calling zones to confirm help is on the way dependent on wiring and field devices usedIncludes a 12V 300mA PSU and 2 volt-free relay contacts which activate on a standard or emergency callInnovative slide-in labelling systemZones can be wired in 4 or 6 core 702 stranded security cableAdditional master controllers and expansion units available for use as repeaters on larger sitesOptional boxed PSUs cw with space for a 12V VRLA battery available for sites where a standby battery facility is required

GBP 234.98
1

C-Tec QT630 Quantec Dimentia Care Master Controller

C-Tec QT630 Quantec Dimentia Care Master Controller

C-Tec QT630 Quantec Dimentia Care Master ControllerAllows care providers to enhance the level of care they provide for patients suffering from dementia Alzheimers incontinence and other degenerative illnesses. Engineer programmable to suit the exact needsof an individual patientbedroom. Includes all of the inputs outputs timers and power needed for the connection of PIRs enuresis sensors bed exit mats LED lights door contacts IRreceivers overdoor lights and more.Key FeaturesCan be configured to automatically switch lights on and off when movement is detected.Provides clear and concise indication of room status data at all relevant Quantec displays.All roompatient call activity is logged at the main Quantec Controller andQuantec Surveyor.Comes with 10 pre-set patient monitoring configurations including high intensity medium-intensity and ensuite ushering.Easily adapted to the changing needs and behaviour patterns ofpatients giving them the freedom and dignity they need to live their lives as normally as possible.

GBP 342.34
1

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920F

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920F

C-Tec NC910EF 10 Zone Expansion Unit for NC910F or NC920FThe NC910EF expands the number of zones on an NC910F or NC920F Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910EF provides 10 extra zones NC920EF provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 185.51
1

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920F

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920F

C-Tec NC920EF 20 Zone Expansion Unit for NC910F or NC920FThe NC920EF expands the number of zones on an NC910F or NC920F Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910EF provides 10 extra zones NC920EF provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 222.61
1

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920S

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920S

C-Tec NC920ES 20 Zone Expansion Unit for NC910S or NC920SThe NC920ES expands the number of zones on an NC910S or NC920S Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910ES provides 10 extra zones NC920ES provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 228.82
1

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920S

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920S

C-Tec NC910ES 10 Zone Expansion Unit for NC910S or NC920SThe NC910ES expands the number of zones on an NC910S or NC920S Call Controller by 10 or 20 zones dependent on model purchased. It is housed in an attractive surface mounting plastic enclosure measuring just 214mm x178mm.Key FeaturesNC910ES provides 10 extra zones NC920ES provides 20 extra zonesInnovative slide-in labelling systemIncludes 10 or 20 Zonal Alarm LEDs capable of indicating Standard and Emergency CallsNote this expansion controller does not include on onboard buzzer as audible call indication will come from the master controller it is connected to

GBP 191.70
1

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with Handset

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with Handset

C-Tec EVC301RLK Type A Red Key Lockable Telephone Outstation with HandsetAn attractive Type Afire telephoneoutstation cw telephone-style handset. Supplied in a durable lift key lockablered steel case. Ideal for use infire telephone and stadium marshalling applications. Allows stewards and fire marshalsto communicate with a SigTEL Master Controller and vice versa. Facilitatesreliable two-way communication in a fire emergency between a permanently manned control room and key points ofasite.Key FeaturesTrue duplex speechCan be surface mounted using a T-BEZ302 bezelMeets and exceeds the requirements of BS 5839-9 when correctly installed

GBP 245.40
1

C-Tec HAK1 HUSH-ACTIV BS 5839-6 Grade C Stand-Alone Domestic Fire Alarm Kit

C-Tec HAK1 HUSH-ACTIV BS 5839-6 Grade C Stand-Alone Domestic Fire Alarm Kit

C-Tec HAK1 HUSH-ACTIV BS 5839-6 Grade C Stand-Alone Domestic Fire Alarm KitA conventional stand-alone Grade C domestic fire detection and alarm system to BS 5839-6 2019 for use in individual flats and apartments Supplied as a cost-effective kit for ease of specification and ordering Includes all of the devices you need to create a typical LD2 dwelling system additional ActiV detection and alarm devices available to accommodate larger systems or systems requiring LD1 coverage. Monitored for head removal openshort circuit faults Attractive double gang Hush-ActiV controller comes with its own rechargeable 72 hour standby battery and separate mains power supply unit Uses attractively designed EN54 certified detection and alarm devices In excess of 10 years battery life in normal usage Designed and manufactured by C-TEC in the UK NEED a Hush system that connects to a landlord system.HAK1 Kit Contents1 x Hush-ActiV Controller cw 72 hour standby battery1 x 24V 250mA PSU1 x ActiV multi sensor1 x ActiV smoke detector1 x ActiV heat detector3 x ActiV detector bases1 x ActiV base sounder cw lid adaptor plateOptional decor plates available for use with ceiling mounted ActiV devices to cover the larger hole left when used to retrofit older Grade D alarm devices.

GBP 259.73
1

C-Tec EVC302GF Type B Green Handsfree EVC Flush Outstation

C-Tec EVC302GF Type B Green Handsfree EVC Flush Outstation

C-Tec EVC302GF Type B Green Handsfree EVC Flush OutstationAn attractive Type B disabled refuge outstation suitable for use with C-TECs SigTEL disabled refuge emergency voice communication system. Allows anyone located in a disabled refuge area to communicate with a SigTEL Master Controller at the touch of a button and vice versa.Key FeaturesStylishly finished in tough durable green steelOffers true duplex speechFeatures a Push to Call or Answer button a Call in Progress LED buzzermicrophone and loudspeakerIncludes connections for an optional induction loop system and a general-purpose open collectoroutput that closes on activation of the unitMeets and exceeds the requirements of BS 5839-9 when correctly installed

GBP 180.59
1

C-Tec EVC302GS Type B Green Handsfree EVC Surface Outstation

C-Tec EVC302GS Type B Green Handsfree EVC Surface Outstation

C-Tec EVC302GS Type B Green Handsfree EVC Surface OutstationAn attractive Type B disabled refuge outstation allows anyone located in a disabled refuge area to communicate with a SigTEL Master Controller at the touch of a button and vice versa. Suitable for use with C-TECs SigTEL disabled refuge emergency voice communication system.Key FeaturesStylishly finished in tough durable green steel.Offers true duplex speech.Features a Push to Call or Answer button a Call in Progress LED buzzermicrophone and loudspeaker.Includes connections for an optional induction loop system and a general-purpose open collectoroutput that closes on activation of the unit.Meets and exceeds the requirements of BS 5839-9 when correctly installed.

GBP 192.44
1

C-Tec EVC302F Type B Stainless Steel Handsfree EVC Flush Outstation

C-Tec EVC302F Type B Stainless Steel Handsfree EVC Flush Outstation

C-Tec EVC302F Type B Stainless Steel Handsfree EVC Flush OutstationAn attractive Type B disabled refuge outstation. Stylishly finished in high-quality brushed stainless steel. Suitable for use with C-TECs SigTEL disabled refuge emergency voice communication system. Allows anyone located in a disabled refuge area to communicate with a SigTEL Master Controller at the touch of a button and vice versa.Key FeaturesOffers true duplex speech.Features a Push to Call or Answer button a Call in Progress LED buzzermicrophone and loudspeaker.Includes connections for an optional induction loop system and a general-purpose open collectoroutput that closes on activation of the unit.Meets and exceeds the requirements of BS 5839-9 when correctly installed.

GBP 200.64
1

C-Tec EVC302S Type B Stainless Steel Handsfree EVC Surface Outstation

C-Tec EVC302S Type B Stainless Steel Handsfree EVC Surface Outstation

C-Tec EVC302S Type B Stainless Steel Handsfree EVC Surface OutstationAn attractive Type B disabled refuge outstation. Stylishly finished in high-quality brushed stainless steel. Suitable for use with C-TECs SigTEL disabled refuge emergency voice communication system. Allows anyone located in a disabled refuge area to communicate with a SigTEL Master Controller at the touch of a button and vice versa.Key FeaturesOffers true duplex speech.Features a Push to Call or Answer button a Call in Progress LED buzzermicrophone and loudspeaker.Includes connections for an optional induction loop system and a general-purpose open collectoroutput that closes on activation of the unit.Meets and exceeds the requirements of BS 5839-9 when correctly installed.

GBP 213.82
1

C-Tec NC951SS Conventional Stainless-Steel Emergency Assistance Alarm Kit

C-Tec NC951SS Conventional Stainless-Steel Emergency Assistance Alarm Kit

C-Tec NC951SS Conventional Stainless-Steel Emergency Assistance Alarm KitA high-quality brushedstainless-steel single zone emergency assistance alarm. Allows a distressed person to raise an alarm in the event of an emergency. To operate the user pulls the cord of theceiling pull to activate a light and sounder outside the WC and on the systems Call Controller.Key FeaturesAttractively designed easy to install and simple to useIncludes an NC941SS 12V Stainless Steel Call Controller NC806CSSS Stainless Steel Overdoor Light cw Sounder NC809DBSS Stainless Steel Reset Point and anNC807C PlasticCeiling PullCan be wired in 4 core stranded security cableSuitable for use in some high-profile disabled persons toilet alarm applications. Please note if a fully BS8300 compliant accessible toilet alarm system is required consider using our NC951 standard plastic kit instead

GBP 225.46
1