8 results (0,12548 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec CFP760 8 Zone Repeater Panel

C-Tec CFP760 8 Zone Repeater Panel

C-TecCFP7608Zone Repeater PanelCan be used to repeat the functions of a master CFP standard or AlarmSense 2-8 zone fire panel at remote parts of site e.g. all potential fire service entrances.Key FeaturesUp to 8 repeaters per CFP masterIncludes its own Mains power supply that requires its own standby battery supplyProvides the user with access to all AL1 and AL2 functionsMasterRepeater communication achieved using CFP761 network driver cards one CFP761 is supplied with the Repeater an additional CF761 card is required at the master CFPCommunicates over screened two-wire fire resistant cableTotal repeater network cable length should not exceed 1KMAttractive flush or surface mountable plastic lid and enclosure - no bezel required

GBP 184.55
1

C-Tec FF396-2 FP10 10Z Fire Repeater Panel

C-Tec FF396-2 FP10 10Z Fire Repeater Panel

C-Tec FF396-2 FP10 10Z Fire Repeater PanelThe Repeater Panel displays the zones from which a fire condition has been initiated by illumination of a steady red lights.When the alarm sounders are silenced at the main control panel the zone lights on the Repeater Panel are extinguished and the Fault light is illuminated. This state is maintained until the main control panel is Reset or other Zones are triggered.The Fault light is also illuminated in the case of a Lamp Test or fault condition at the main control panel. The nature of the fault is not indicated and must be determined at the Main Control Panel.When mains power to the whole Fire Alarm system is correct then a green Mains On light is illuminated.The Repeater Panel has an integral fault sounder which mimics the Main Control Panel fault sounder and thus can be muted from the main control panel.

GBP 306.76
1

C-Tec FF596 MFP 8 Zone Repeater Panel

C-Tec FF596 MFP 8 Zone Repeater Panel

C-Tec FF596 MFP 8 Zone Repeater PanelAn MFP 8 zone repeater panel.C-TECs FP and MFP ranges of conventional fire panels have been protecting people and property for over 25 years.Designed to comply with BS5839-4 they are supplied in robust metal enclosures with lift-off lids and heavy-duty base connections.Their broad compatibility with virtually all known conventional smoke and heat detectors and their ability to interpret a short circuit as a fire or fault make them particularly useful for retro-installations.

GBP 408.20
1

C-Tec XFP510-32 XFP Repeater Panel 32 Zone

C-Tec XFP510-32 XFP Repeater Panel 32 Zone

C-Tec XFP510-32 XFP Repeater Panel 32 ZoneCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances. Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3. Includes an on-board fault relay. Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel. Communication between the XFP Main panel and Repeater requires an AFP711 network driver card fitted as standard in all XFP510-32s available as an optional extra on Main XFP 32 Zone panels. Repeater network wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.Key FeaturesCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances.Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3.Includes an on-board fault relay.Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel.Communication between the XFP Main panel and Repeater requires an AFP711 network driver card fitted as standard in all XFP510-32s available as an optional extra on Main XFP 32 Zone panels.Repeater network is non-redundant and wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.

GBP 433.36
1

C-Tec XFP510-16 XFP Repeater Panel 16 Zone

C-Tec XFP510-16 XFP Repeater Panel 16 Zone

C-Tec XFP510-16 XFP Repeater Panel 16 ZoneCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances. Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3. Includes an on-board fault relay. Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel. Communication between the XFP Main panel and Repeater requires a CFP761 network driver card fitted as standard in all XFP510-16s available as an optional extra on Main XFP 16 Zone panels. Repeater network wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.Key FeaturesCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances.Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3.Includes an on-board fault relay.Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel.Communication between the XFP Main panel and Repeater requires a CFP761 network driver card fitted as standard in all XFP510-16s available as an optional extra on Main XFP 16 Zone panels.Repeater network wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.

GBP 315.26
1