18 results (0,13593 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

C-Tec CFP760 8 Zone Repeater Panel

C-Tec CFP760 8 Zone Repeater Panel

C-TecCFP7608Zone Repeater PanelCan be used to repeat the functions of a master CFP standard or AlarmSense 2-8 zone fire panel at remote parts of site e.g. all potential fire service entrances.Key FeaturesUp to 8 repeaters per CFP masterIncludes its own Mains power supply that requires its own standby battery supplyProvides the user with access to all AL1 and AL2 functionsMasterRepeater communication achieved using CFP761 network driver cards one CFP761 is supplied with the Repeater an additional CF761 card is required at the master CFPCommunicates over screened two-wire fire resistant cableTotal repeater network cable length should not exceed 1KMAttractive flush or surface mountable plastic lid and enclosure - no bezel required

GBP 184.55
1

C-Tec FF396-2 FP10 10Z Fire Repeater Panel

C-Tec FF396-2 FP10 10Z Fire Repeater Panel

C-Tec FF396-2 FP10 10Z Fire Repeater PanelThe Repeater Panel displays the zones from which a fire condition has been initiated by illumination of a steady red lights.When the alarm sounders are silenced at the main control panel the zone lights on the Repeater Panel are extinguished and the Fault light is illuminated. This state is maintained until the main control panel is Reset or other Zones are triggered.The Fault light is also illuminated in the case of a Lamp Test or fault condition at the main control panel. The nature of the fault is not indicated and must be determined at the Main Control Panel.When mains power to the whole Fire Alarm system is correct then a green Mains On light is illuminated.The Repeater Panel has an integral fault sounder which mimics the Main Control Panel fault sounder and thus can be muted from the main control panel.

GBP 306.76
1

C-Tec FF596 MFP 8 Zone Repeater Panel

C-Tec FF596 MFP 8 Zone Repeater Panel

C-Tec FF596 MFP 8 Zone Repeater PanelAn MFP 8 zone repeater panel.C-TECs FP and MFP ranges of conventional fire panels have been protecting people and property for over 25 years.Designed to comply with BS5839-4 they are supplied in robust metal enclosures with lift-off lids and heavy-duty base connections.Their broad compatibility with virtually all known conventional smoke and heat detectors and their ability to interpret a short circuit as a fire or fault make them particularly useful for retro-installations.

GBP 408.20
1

C-Tec ZREP1SCA ZFP Multipath Repeater S CAST

C-Tec ZREP1SCA ZFP Multipath Repeater S CAST

C-Tec ZREP1SCA ZFP Multipath Repeater S CASTAn optional CAST ZFP network device that can be used as atraditional but compact repeater panel with added functionality. It includes aZ41 Touchscreen Control Module and ZHN Hi-Net multi-path fault-tolerantnetwork PCB.Housed in a stylish flush mounting plastic enclosuremeasuring just 214mm x 178mm.The ZREP1SCA can be used to an enhance a buildingsreception area and access points locate your main ZFP panels out of sight andlet our ZFP Compact Controllers add a touch of class to your surroundings.Key FeaturesFull Access Level 2 functionality silence disable resetetcRequires a separate EN54-4 boxed PSU such as C-TECsBF360-24 1A 24V boxed PSUUp to 64 Compact Controllers can be connected to a ZFPnetwork each controller classed as 1 network node

GBP 650.04
1

C-Tec XFP510-32 XFP Repeater Panel 32 Zone

C-Tec XFP510-32 XFP Repeater Panel 32 Zone

C-Tec XFP510-32 XFP Repeater Panel 32 ZoneCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances. Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3. Includes an on-board fault relay. Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel. Communication between the XFP Main panel and Repeater requires an AFP711 network driver card fitted as standard in all XFP510-32s available as an optional extra on Main XFP 32 Zone panels. Repeater network wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.Key FeaturesCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances.Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3.Includes an on-board fault relay.Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel.Communication between the XFP Main panel and Repeater requires an AFP711 network driver card fitted as standard in all XFP510-32s available as an optional extra on Main XFP 32 Zone panels.Repeater network is non-redundant and wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.

GBP 433.36
1

C-Tec XFP510-16 XFP Repeater Panel 16 Zone

C-Tec XFP510-16 XFP Repeater Panel 16 Zone

C-Tec XFP510-16 XFP Repeater Panel 16 ZoneCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances. Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3. Includes an on-board fault relay. Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel. Communication between the XFP Main panel and Repeater requires a CFP761 network driver card fitted as standard in all XFP510-16s available as an optional extra on Main XFP 16 Zone panels. Repeater network wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.Key FeaturesCan be used to repeat the functions of an XFP Main panel at remote parts of a site e.g. all potential fire service entrances.Offers all of the functions and controls of an XFP Main panel access levels 1 2 and 3.Includes an on-board fault relay.Requires its own dedicated Mains power and battery back-up supply.A maximum of eight XFP Repeaters can be connected to one non-networked XFP Main panel.Communication between the XFP Main panel and Repeater requires a CFP761 network driver card fitted as standard in all XFP510-16s available as an optional extra on Main XFP 16 Zone panels.Repeater network wired in 1.5 mm2 two-core screened fire resistant cable. Network length must not exceed 500 metres.

GBP 315.26
1

C-Tec ZREP1FCA ZFP Multipath Repeater F CAST

C-Tec ZREP1FCA ZFP Multipath Repeater F CAST

C-Tec ZREP1FCA ZFP Multipath Repeater F CASTAn optional CAST ZFP network device that can be used as atraditional but compact repeater panel with added functionality. It includes aZ41 Touchscreen Control Module and ZHN Hi-Net multi-path fault-tolerantnetwork PCB.Housed in an stylish flush mounting plastic enclosuremeasuring just 214mm x 178mm.The ZREP1FCA can be used to an enhance a buildingsreception area and access points locate your main ZFP panels out of sight andlet our ZFP Compact Controllers add a touch of class to your surroundings.Key FeaturesFull Access Level 2 functionality silence disable resetetcRequires a separate EN54-4 boxed PSU such as C-TECsBF360-24 1A 24V boxed PSUUp to 64 Compact Controllers can be connected to a ZFPnetwork each controller classed as 1 network nodeGlazed stainless steel frames ZBEZDCSS and vertical andhorizontal alignment plates ZMBOXAL ZMBOXAS also available

GBP 650.04
1

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761

C-Tec CFP Network Driver Card CFP761An optional system expansion device for use with CFP Standardand CFPAlarmSense conventional fire panels.This part must be used if you require the use of a repeater panel or you wish to network compatible XFP panels together.Key FeaturesAllows the connection of up to eight CFP760 Repeaters one CFP761 required per Main all CFP760 repeaters include a CFP761 as standardCommunicates over screened two-wire fire resistant cableTotal repeater network cable length should not exceed 1KM

GBP 61.67
1

C-Tec ZREP1F ZFP Compact Controller Flush Mounted

C-Tec ZREP1F ZFP Compact Controller Flush Mounted

C-TecZREP1FZFP Compact Controller Flush MountedThe ZFP controller is an optional ZFP network device that can be used as a traditional but compact repeater panel with added functionality. Includes a Z41 Touchscreen Control Module and ZHN Hi-Net multi-path fault-tolerant network PCB. Housed in an stylish flush mounting plastic enclosure measuring just 214mm x178mm.Can be used to an enhance a buildings reception area and access points locate your main ZFP panels out of sight and let our ZFP Compact Controllers add a touch of class to your surroundings. Full Access Level 2 functionality silence disable reset etc. Requires a separate EN54-4 boxed PSU such as C-TECs BF360-24 1A 24V boxed PSU. Up to 64 Compact Controllers can be connected to a ZFP network each controller classed as 1 network node.

GBP 648.28
1

C-Tec ZREP1S ZFP Compact Controller Surface Mounted ZREP1S

C-Tec ZREP1S ZFP Compact Controller Surface Mounted ZREP1S

C-TecZREP1SZFP Compact Controller Surface Mounted ZREP1SThe ZFP controller is an optional ZFP network device that can be used as a traditional but compact repeater panel with added functionality. Includes a Z41 Touchscreen Control Module and ZHN Hi-Net multi-path fault-tolerant network PCB. Housed in a stylish surface mounting plastic enclosure measuring just 214mm x178mm x 70mm.Can be used to enhance a buildings reception area and access points locate your main ZFP panels out of sight and let our ZFP Compact Controllers add a touch of class to your surroundings. Full Access Level 2 functionality silence disable reset etc. Requires a separate EN54-4 boxed PSU such as C-TECs BF360-24 1A 24V boxed PSU. Up to 64 Compact Controllers can be connected to a ZFP network each controller classed as 1 network node.

GBP 648.28
1

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications Card

C-Tec AFP711 XFP Network Communications CardAn optional system expansion device for use with XFP 12 Loop 32 Zone fire panels. Allowsthe connection of up to eight XFP Repeaters or eight XFP Main panels any mix on an RS485 network. One AFP711 card required per networked Main XFP 12 Loop 32 Zone panel note that XFP510-16 and XFP510-32 repeaters include a network driver card as standard.The AFP711 is NOT compatible with XFP Single Loop 16 Zone panels which require a CFP761 card for networking.Key network protocol features when used for interconnecting XFP main panelsCan be used to connect up to 8 XFP main panels any mix over a two-wire RS485 network of up to 1KM in length.Each networked XFP can be programmed to accept Fires Faults and Control actions such as Silence Alarm Sounders and Control Panel Resets from other panels.Each XFP will accept Disablement commands for zones sounders and output sets from other panels.All panels monitored for network wiring faults.Fires and faults on remote panels are displayed on local panels including the point description.CEs can be programmed into local panels dependent on which remote panel is in alarm.The network supports the programming of site data into remote panels from a PC at a local panel.Time and date is common to all panels.All networked main panels require a network communication card.It is not possible to mix XFP main panels and XFP repeaters on the same network.Key network protocol features when used for connecting XFP repeatersCan be used to connect up to 8 XFP repeaters any mix to one XFP main panel.Up to 500m of cable may be fitted to an XFP two-wire repeater network.Each XFP repeater offers all the functions and controls of an XFP main panel.The XFP main panel must have a network communication card fitted.It is not possible to mix XFP main panels and XFP repeaters on the same network.

GBP 114.65
1

C-Tec XFP761 XFP Network Card For 16 Zone Panels

C-Tec XFP761 XFP Network Card For 16 Zone Panels

C-Tec XFP761 XFP Network Card For 16 Zone PanelsThe XFP network card allows for the connection of up to eight mainpanels any mix over a two-wire RS485 network spanning up to 1KM. Eachnetworked XFP panel can be programmed to receive fire alerts faults andcontrol commands such as silencing alarm sounders and resetting controlpanels from other connected panels.Key FeaturesCan be used to connect up to 8 XFP repeaters any mix toone XFP main panelUp to 500m of cable may be fitted to an XFP two-wirerepeater networkEach XFP repeater offers all the functions and controls ofan XFP main panelThe XFP main panel must have a network communication cardfittedIt is not possible to mix XFP main panels and XFP repeaterson the same networkOne XFP761 required per networked Main XFP Single Loop 16Zone fire panel note that XFP510-16 and XFP510-32 repeaters include a networkdriver card as standardThe XFP761 is NOT compatible with XFP 12 Loop32 Zone fire panels which require an AFP711 card for networking

GBP 74.52
1

C-Tec NC832KE Conventional 30 Zone Surface Emergency Master Panel

C-Tec NC832KE Conventional 30 Zone Surface Emergency Master Panel

C-Tec NC832KE Conventional 30 Zone Surface Emergency Master PanelNC812KE NC822KE and NC832KE indicator panels are fully compatible with all 800 Series call points ceiling pulls infrared ceiling receivers monitoring points overdoor lights and remote sounders.Depending on the devices wired to it Standard and Emergency calls can be indicated via its buzzer and zonal LEDs. An optional Mute button is also provided to allow the user to silence standard calls.Standard Calls when triggered by a calling device the indicator panels internal buzzer sounds continuously and the relevant zone indicators illuminate steady.Pressing the Indicator Panels Mute Button if fitted silences the Panels internal buzzer. However if a new call standard or emergency is triggered anywhere on the system the buzzer will resound.Emergency Calls when triggered by a calling device theIndicator Panels internal buzzer pulses and the relevant zone indicators flash. This level of call takes priority over standard calls and cannot be muted at the Panel. An emergency call can only be reset at the device from which it was triggered or via a reset point wired on the same zone.Key FeaturesFully compatible with C-TECs entire range of 800 Series Call System componentsCapable of indicating standard constant tone and emergency intermittent tone calls10 20 or 30 zonal alarm LEDs dependent on model purchased see below for parts listingOptional mute button2 volt-free relay contactsSurface mountingConnections for optional Repeater panels and sounders to increase call indication levels

GBP 466.69
1