tamiya the frog from GBP 6 | See the cheapest prices and offers on css.lazzaweb.dk

Cooper Bi-Wire External Relay 24v BWEXTR24V

Cooper Bi-Wire External Relay 24v BWEXTR24VThe BiWire Ultra output relay module is designed to provide a simple means of interfacing BiWire Ultra systems with external equipment such as door retainers. It is simple to install and can provide additional flexibility to an installer as external switching can be achieved without having to wire back to the main fire alarm control panel. The module range is available in 24V and 230V variants.Key FeaturesQuick and simple to installProvides flexibility at system installation24V and 230V variants provide for low or mains voltage switchingInstallationRemove the lid from the back box.Unclip the PCB from the mounting pillars to prevent damage during drilling.Remove the mounting plate via the two screws so you can gain access to the base of the back box.Mark on the back box where the glands will be fitted making sure there is sufficient space between glands so they can be tightened properly.Using the appropriate sized cutting drill for the gland size used drill out the marked gland points on the back-box.Fit the glands to the newly drilled holes in the back box.Drill the holes in the wall to match the holes in the back box see picture on right.Screw the back-box in position see picture on right.Screw the mounting plate back into the back box.Clip the PCB into the mounting pillars on the mounting plate.Pass the wires through the glands and secure to the PCB as outlined in the wiring instructions.Secure the lid to the back box.

GBP 100.50

1

Cooper MARDF6 Auxiliary Output Module

Cooper MARDF6 Auxiliary Output ModuleThe MARDF6 is an Auxiliary Output Module designed for use with the DF6000 panel.InstallationMount the PCB using the plastic feet providedThe PCB should be mounted as physically close to the external equipment as possibleConnect the PCBEnd of Line Monitoring devices are incorporated within the MARDF6 PCB remove and discard the end of line devices from the relevant outputs of the DF6000 panelConnect 24V to the PCV this can be derived from the auxiliary output of the DF6000 panel

GBP 56.05

1

Cooper CIT420 Addressable 4-20mA Interface

Cooper CIT420 Addressable 4-20mA InterfaceThe CIT420 Addressable 4-20mA Interface is compatible with Eaton analogue addressable control panels.This interface has a unique address on the loop.InstallationSeparate the two halves of the unitDrill out or knock out the required cable entries in the surface mounting back-boxFit the back-box in position and pass the wires into itConnect the unitSet the required threshold levels via the DIL switches

GBP 136.57

1

Cooper CIT420R Addressable 4-20mA Interface

Cooper CIT420R Addressable 4-20mA InterfaceThe CIT420R 4-20 mA addressable interface is compatible with Cooper analogue addressable control units. This interface has a unique address on the loop. Each relay is programmable with its own sensitivity level which can be expressed as a percentage of L.E.L Explosion Limit Level or PPM Parts per million through the arrangement of the DIL microswitches.InstallationSeparate the two halves of the unitDrill out or knock out the required cable entries in the surface mounting back-boxFit the back-box in position and pass the wires into itConnect the unit according to the diagram belowSet the required threshold levels via the DIL switches

GBP 197.16

1

Cooper ZPCB2252-MSL Mimic PCB Slave - Logic Output

Cooper ZPCB2252-MSL Mimic PCB Slave - Logic Output The ZPCB2252-MSL is the slave PCB which has no loop interface to the CIE but is directly controlled by the ZPCB2252-MML board. Up to 7 slave boards can be daisy chained to the master board and each slave has 32 LED outputs allowing the number of LED outputs to be expanded up to a maximum of 250 not all LEDs on the 7th slave are used. The power to these additional LEDs is also from the external power supply but is transferred through the interlinking cable between boards.Please refer to the datasheet for more information.

GBP 171.56

1

Cooper EOLM-3 End of Line Module Bi-Wire Circuits Box of 8

Cooper EOLM-3 End of Line Module Bi-Wire Circuits Box of 8Each Zone on the panel that is configured for BiWire mode must have the intelligent end of line module EOLM-3 fitted to continually monitor each zone for the presence of fault conditions such as detector head removal open or short circuit and for end of line failures even when in a Fire condition.For new installations any Zone on the panel that is configured for Conventional mode can use the intelligent end of line module EOLM-3 to terminate the zone but the panel will be limited to only detecting the presence of open or short circuit conditions to make it backward compatible with the EOLM-1. All detector head removals will be seen as an open circuit condition. The EOLM-3 module can be placed into the base of the last manual call point or detector base.

GBP 44.06

1

Cooper MDP201 Duct Probe requires detector and base

Cooper MDP201 Duct Probe requires detector and baseThe presence of smoke in a ventilation duct is detected by sampling the airflow through the duct via two sampling tubes. A detector and base are mounted within the sampling chamber which is located on the external skin of the duct with sample and exhaust probes passing into the duct in an area of low turbulence. The unit requires an analogue optical detector and base and is supplied with full fixing instructions.

GBP 306.96

1

Cooper EAA16-LS Toilet Alarm Outstation Master - Light Grey - Surface Mount

Cooper EAA16-LS Toilet Alarm Outstation Master - Light Grey - Surface MountThe Emergency Assist Alarm - VoCALL kit has been specifically designed to integrate disabled call functions into the VoCALL digital range providing the perfect solution for conformity with local building regulations and country codes of practice.By integrating the VoCALL kit with the Emergency Voice Communication System all calls relating to disabled communications can be monitored on the same VoCALL system.This emergency assist solution is fully monitored and battery backed by the VoCALL system saving local power supplies and giving confidence in the system integrity. The alarm shows up as a call on the VoCALL system but has no speech path so a conversation cannot be had with the occupant use of the Type B outstations will allow this.Key FeaturesRemote powered from the VoCALL digital systemNo additional VoCALL system connection equipment requiredDual loop pull cordHigh contrast labelsBraille on cancel plateBlue indicationNo PSU required remotely powered by VoCALL systemCalls from disabled toilets and refuge points are monitored from one location

GBP 194.04

1

Cooper EC0232 Lon to RS232 Adapter

Cooper EC0232 Lon to RS232 AdapterThe Lon to RS232adapter EC0232allows connection of the Cooper system network LonWorks devices to PC based applications such as site monitor site graphics.The EC0232PAVA offers a similar interfacing facility to the HMX PAVA public addressvoice alarm system by withholding the handshaking functionality and if required the EC0232PAVA3D offers an additional 3 minute time delay before the voice alarm function is actuated. The bi-directional link allows the status of the HMX PAVA system to be displayed and monitored at the control panel. Different messages may be played depending on the configuration of the cause and effect programming.The interface may be located anywhere on the Cooper peer to peer network allowing information from any intelligent addressable control panel to be routed through the bi-directional RS232 port to PC or PAVA system.Key FeaturesAllows connection of Cooper system network devices to PC based applicationsCan be connected at any point on peer to peer networkAllows Cooper system network to be connected to PC or PAVABenefitsIntegrates PC based applicationsIntegrates PAVA systems site monitor and graphpackFlexibility to use any PC application

GBP 406.33

1

Cooper NCDR Dual Redundant Network Card

Cooper NCDR Dual Redundant Network CardThe NCDR is the heart beat of the Cooper true Pier-to Pier fault tolerant network. It allows information from any Cooper input and output device to be passed over the network and display on any Cooper Addressable Fire panels or remote display such the Sire monitor or the Cooper Graphic Package. Information such as Fire General Alarm Pre-alarm Faults Disablement and status information from any panel is accessible on the Cooper Pier to Pier network thus allowing site wide cause and effect functionality.Simply by adding and connecting the NCDR network card allows any Cooper addressable Fire Alarm control Panel to be networked. All other panels on the network will be instantly aware of a panel as soon as it is given valid network address thus allowing additional panels to be added at any time with a minimum amount of re-programming. The NCDR dual channel serial gateway consists of two channels each using a FT3150 Smart transceiver and FT-X1 communication transformer.Each Neuron supports a serial 232 interface allowing the Master Neuron to communicate with the host equipment and also to send messages to and receive messages from the Slave Neuron. This allows nodes to communicate using 2 separate networks simultaneously thereby providing continuous communication in the event of open or short circuit faults on either network. Software prevents the duplication of messages. The network can be mounted inside the cooper addressable fire panels.

GBP 318.67

1

Cooper Menvier EOLM-1 End Of Line Module

Cooper Menvier EOLM-1 End Of Line ModuleEach Zone on the panel that is configured for Standard Conventional mode must have the intelligent end of line module EOLM-1 fitted to continually monitor each zone for the presence of fault conditions such as detector head removal open or short circuit and for end of line failures even when in a Fire condition. The EOLM-1 module can be placed into the base of the last manual call point or detector base.

GBP 5.51

1

Cooper LP800KIT Loop Tester Kit

Cooper LP800KIT Loop Tester KitThe loop tester kit LP800KIT is a hardware software combination that can be used to test commission and fault find a loop of up to 200 intelligent addressable devices sensors sounders ancillary devices without having to connect the loop to Eatons intelligent addressable control panel. The loop tester is connected between the loop and PC.It allows the engineer to quickly identify and locate any loop device that is operating outside its operating conditions by varying the alarm threshold of any loop device alarm pre-alarm and fault.The Loop tester hardware requires a free serial port on the PC either internet or via a USB extension a mains power supply and a direct connection to the device loop.Key FeaturesPre-addressing Identifies all field devices and determines their address and device type.Analogue values Constantly displays in real time the analogue value of all loop devices in order to determine their status.Test LED This command operates the LED of any inputs sensorscall points as well as controls the outputs of sounders and output modules.Device settings Analogue values of all devices can be interpreted according to ranges which can be set and altered by the user OK pre-alarm fire.Event Log A history of events can be stored from the date the application was started.Soft addressing Automatically assigns a new and potentially different address to every device found on the loop.

GBP 623.41

1

Cooper CFVCEA Pullkit without PSU Connects to EVCS Panel or CFEASL4

Cooper CFVCEA Pullkit without PSU Connects to EVCS Panel or CFEASL4It has now become very common for the disabled toilet to be specified as part of the refuge system. The CFVCEA has been specifically designed to integrate disabled call functions into the VoCALL network or VoCALL compact ranges providing the perfect solution for conformity with the Building Regulations Document M and Equality Act 2010.Disabled toilet alarms are required by Building Regulation Document M and by integrating it with the Emergency Voice Communication System all calls relating to disabled communications can be displayed in a single point.The CFVCEA solution is fully monitored and battery backed by the VoCALL system saving local power supplies and giving confidence in the system integrity.The CFVCEA shows up as a call on the VoCALL system but has no speech path so a conversation cannot be had with the occupant use of the type B outstations would allow this.Features Monitored to BS5839 Pt9Remote powered from VoCALL exchangeDual loop pull cordHigh contrast labelsBraille on cancel plateBlue indicationBenefits Saving power no PSU is required remote powered by VoCALL system.One install saves running 2 separate systems.One location all calls from disabled toilets and refuge points monitored from one location.Tactile braille signage to assist partially sighted people to easily operate the cancel plate.

GBP 51.08

1

Cooper FX003W Conventional Flush Sounder White MFS324W

Cooper FX003W Conventional Flush Sounder WhiteTwo versions of the conventional flush sounders are available in this range the red FX003 and the white FX003W. Both the FX003 and the FX003W are compatible with the Eaton range of conventional fire systems. These conventional flush sounders provide an excellent combination of high sound output and discreet appearance. Ideal for retail hotel and residential applications such as sheltered housing.Features and benefitsChoice of coloursSeparate volume controlChoice of tone is determined by selection of appropriate terminal for negative connectionQuick and simple to installDiscreet low-profile designEasy to maintainservice

GBP 36.58

1

Cooper FX003 Conventional Flush Sounder - Red MFS324

Cooper FX003 Conventional Flush Sounder - RedTwo versions of the conventional flush sounders are available in this range the red FX003 and the white FX003W. Both the FX003 and the FX003W are compatible with the Eaton range of conventional fire systems. These conventional flush sounders provide an excellent combination of high sound output and discreet appearance. Ideal for retail hotel and residential applications such as sheltered housing.Features and benefitsChoice of coloursSeparate volume controlChoice of tone is determined by selection of appropriate terminal for negative connectionQuick and simple to installDiscreet low-profile designEasy to maintainservice

GBP 36.58

1

Cooper Bi-Wire Flexi 2 Zone Panel EFBW2ZFLEXI

Cooper Bi-Wire Flexi 2 Zone Panel EFBW2ZFLEXIBiWire Flexi combines two technologies to provide a truly versatile fire safety solution. The panel can be configured to allow either two-wire or conventional devices to work on a zone. Each zone is individually configurable so a mixture of types can therefore be installed on the same system. This provides you with the flexibility to utilise all the time-saving benefits of a two-wire system with the ability to use a wide range of conventional devices where required.It shares the same straightforward intuitive interface as the BiWire Ultra and EFCV8Zone conventional panels providing a proven solution for simple programming and maintenance. The BiWire Flexi fire alarm system is certified to EN54 part2 and part 4 and is designed to meet the recommendations of BS5839Key FeaturesConfigure zone wiring to work as either a conventional or two-wire systemAvailable in 2 4 and 8 zone variantsAllows the connection of an existing conventional system to a BiWire systemCompatible with two-wire and conventional EN 54-23 certified visual alarm devices VADsReduces stock-holding and enables the fire system to adapt to the demands of the customer or applicationSimple to sell and specify Flexi can be used in a wide variety of applications and is very simple to installSave time money and effort when undertaking system extensions and upgradesUp-to-date with latest regulations

GBP 220.32

1

Cooper Bi-Wire Flexi 8 Zone Panel EFBW8ZFLEXI

Cooper Bi-Wire Flexi 8 Zone Panel EFBW8ZFLEXIBiWire Flexi combines two technologies to provide a truly versatile fire safety solution. The panel can be configured to allow either two-wire or conventional devices to work on a zone. Each zone is individually configurable so a mixture of types can therefore be installed on the same system. This provides you with the flexibility to utilise all the time-saving benefits of a two-wire system with the ability to use a wide range of conventional devices where required.It shares the same straightforward intuitive interface as the BiWire Ultra and EFCV8Zone conventional panels providing a proven solution for simple programming and maintenance. The BiWire Flexi fire alarm system is certified to EN54 part2 and part 4 and is designed to meet the recommendations of BS5839.Key FeaturesConfigure zone wiring to work as either a conventional or two-wire systemAvailable in 2 4 and 8 zone variantsAllows the connection of an existing conventional system to a BiWire systemCompatible with two-wire and conventional EN 54-23 certified visual alarm devices VADsReduces stock-holding and enables the fire system to adapt to the demands of the customer or applicationSimple to sell and specify Flexi can be used in a wide variety of applications and is very simple to installSave time money and effort when undertaking system extensions and upgradesUp-to-date with latest regulations

GBP 290.23

1

Cooper Bi-Wire Flexi 4 Zone Panel EFBW4ZFLEXI

Cooper Bi-Wire Flexi 4 Zone Panel EFBW4ZFLEXIBiWire Flexi combines two technologies to provide a truly versatile fire safety solution. The panel can be configured to allow either two-wire or conventional devices to work on a zone. Each zone is individually configurable so a mixture of types can therefore be installed on the same system. This provides you with the flexibility to utilise all the time-saving benefits of a two-wire system with the ability to use a wide range of conventional devices where required.It shares the same straightforward intuitive interface as the BiWire Ultra and EFCV8Zone conventional panels providing a proven solution for simple programming and maintenance. The BiWire Flexi fire alarm system is certified to EN54 part2 and part 4 and is designed to meet the recommendations of BS5839.Key FeaturesConfigure zone wiring to work as either a conventional or two-wire systemAvailable in 2 4 and 8 zone variantsAllows the connection of an existing conventional system to a BiWire systemCompatible with two-wire and conventional EN 54-23 certified visual alarm devices VADsReduces stock-holding and enables the fire system to adapt to the demands of the customer or applicationSimple to sell and specify Flexi can be used in a wide variety of applications and is very simple to installSave time money and effort when undertaking system extensions and upgradesUp-to-date with latest regulations

GBP 247.78

1

Cooper Bi-Wire Call Point EF201BWCP

Cooper Bi-Wire Call Point EF201BWCPTwo versions of the BiWire call points are available in this range the EF201BWCP which can be either surface or flush mounted and the EF203BWCPWP which is a weather-proof version. Both the EF201BWCP and the EF203BWCPWP are compatible with the Eatons BiWire range of fire systems.These call points are design for fast and simple installation and are supplied as standard with a frangible glass element and a test key for ease of maintenance. A comprehensive range of accessories is available to maximise the functionality of the call point for particular applications.Key FeaturesFast fit clip on front coverWide range of accessoriesHeavy duty terminalsTwo models availableSingle tool for test and accessRobust constructionIP65 version availableQuick and simple to installEasy to maintain and serviceVersatile installationWeather-proof variant suitable for outside usePlease Note This product is not compatible with the older Cooper Bi-Wire range.

GBP 17.78

1

Cooper Bi-Wire Weatherproof Call Point EF203BWCPWP

Cooper Bi-Wire Weatherproof Call Point EF203BWCPWPTwo versions of the BiWire call points are available in this range the EF201BWCP which can be either surface or flush mounted and the EF203BWCPWP which is a weather-proof version. Both the EF201BWCP and the EF203BWCPWP are compatible with the Eatons BiWire Ultra range of fire systems.These call points are design for fast and simple installation and are supplied as standard with a frangible glass element and a test key for ease of maintenance. A comprehensive range of accessories is available to maximise the functionality of the call point for particular applications.Key FeaturesFast fit clip on front coverWide range of accessoriesHeavy duty terminalsTwo models availableSingle tool for test and accessRobust constructionIP65 version availableQuick and simple to installEasy to maintain and serviceVersatile installationWeather-proof variant suitable for outside usePlease Note This product is not compatible with the older Cooper Bi-Wire range.

GBP 22.03

1

Cooper Bi-Wire Option Board 4 Relay BWOB4Z

Cooper Bi-Wire Option Board 4 Relay BWOB4ZEatons BiWire Ultra Option is an additional daughter card that provides outputs to Fire Protection Equipment FPE Fire Alarm Routing Equipment FRE and Zone Relays. The FRE output is design to activate during a fire event and is connected to phone diallers andor Building Management Systems - the output complies with EN54-2.The FPR output is designed to activate during a fire event and when connected to an external device drive door release mechanism fire screens sprinkler system and gas release systems. Zone relay contacts are volt free and do not provide any voltage. The relays are selectable to be either set to CNO or CNC. The zonal relays are designed to follow the fire condition of the associated zone circuits on the Main Board.

GBP 34.52

1

Cooper Bi-Wire Option Board 8 Relay BWOB8Z

Cooper Bi-Wire Option Board 8 Relay BWOB8ZEatons BiWire Ultra Option is an additional daughter card that provides outputs to Fire Protection Equipment FPE Fire Alarm Routing Equipment FRE and Zone Relays. The FRE output is design to activate during a fire event and is connected to phone diallers andor Building Management Systems - the output complies with EN54-2.The FPR output is designed to activate during a fire event and when connected to an external device drive door release mechanism fire screens sprinkler system and gas release systems. Zone relay contacts are volt free and do not provide any voltage. The relays are selectable to be either set to CNO or CNC. The zonal relays are designed to follow the fire condition of the associated zone circuits on the Main Board.

GBP 44.39

1

Cooper Bi-Wire Conventional Repeater Panel EFBWCV-REPEATER

Cooper Bi-Wire Conventional Repeater Panel EFBWCV-REPEATEREatons new BiWire and Conventional repeater panel is compatible with our 2 zone 4 zone and 8 zone BiWire-Ultra EFBWxZONE BiWire-Flexi EFBWxZFLEXI and latest release of conventional panels EFCV8Z. The EFBWCV repeater panel can be daisy-chained up to 3 panels per control panels.It can repeat information from any zone of the panel it is cabled to. With an integral power supply the only wiring required for the repeater panel is the mains input to the power supply unit and the data cable between the fire control panel and each repeater panel.Key FeaturesCan be used with 2 4 and 8 zone control panelsInternal Power supplySimple unit cablingUp to 3 repeaters per control panelSame modern enclosure as control panelsRepeater panel not out of place in public areas

GBP 201.05

1

Cooper Bi-Wire Option Board 2 Relay BWOB2Z

Cooper Bi-Wire Option Board 2 Relay BWOB2ZEatons BiWire Ultra Option is an additional daughter card that provides outputs to Fire Protection Equipment FPE Fire Alarm Routing Equipment FRE and Zone Relays. The FRE output is design to activate during a fire event and is connected to phone diallers andor Building Management Systems - the output complies with EN54-2.The FPR output is designed to activate during a fire event and when connected to an external device drive door release mechanism fire screens sprinkler system and gas release systems. Zone relay contacts are volt free and do not provide any voltage. The relays are selectable to be either set to CNO or CNC. The zonal relays are designed to follow the fire condition of the associated zone circuits on the Main Board.

GBP 29.59

1

Cooper Menvier EF-GPIO-16WAY 16-Way Input Output Module

Cooper Menvier EF-GPIO-16WAY 16-Way Input Output ModuleThis DIN-rail mounted IO interface features programmable 16 input16 output pins. It can trigger any user defined event to any zoneset of zones in the entire system and transmit audio signal from built in local audio input to any zone over system network.The Voice View Control Station computer is connected to the DAU5000 voice system through a serial RS485 link on the EF-GPIO-16WAY module.In order to complete the RS485 interface connection on the PC side it is required to use a USB to RS485 converter EF-U485 If live audio voice functionality is required the audio source or microphone is connected to the analogue line level audio input located on the same EF-GPIO-16WAY device.

GBP 1703.47

1

Awardvindende Google Marketing Powerhouse

Brand

Merchant

Price (EUR)