13 tommer computer from GBP 130 | See the cheapest prices and offers on css.lazzaweb.dk

Fireclass 508.032.730FC Fireclass Essential 2 Zone Panel

Fireclass 508.032.730FC Fireclass Essential 2 Zone PanelThe Fireclass Essential Panel range is an EN-approved low cost conventional panels that are available in both 2 Zone and 4 Zone variants. The panels can support up to 128 devices with a maximum of 32 devices on each zone. The panels are approved to EN 54-2 EN 54-4 and listed as part of the EN 54-13 system certificate.The panel UI has the following features18 LEDs on the 2 Zone Panel and 22 LEDs on the 4 Zone PanelOne piezo buzzer for audible indicationEight push buttons for user inputsKey FeaturesModern and aesthetic designSurface mountableOption to set delays for outputs during alarmButtons for silence resound and resetTwo open collector outputsDisable feature for sounders and zonesVolt-free fire and fault relaysTest feature for installationTwo auxiliary inputs alert input and class change inputSupport for all FireClass 600 and 700 series conventional detectors conventional sounders and VADsSupport for third party devicesPlease note For full details on all the supported devices refer to the EN 54-13 certificate.Fully compliant with EN 54-2 EN 54-4 and is listed as part of the EN 54-13 system certificate

GBP 194.00

1

Fireclass 508.032.731FC Fireclass Essential 4 Zone Panel

Fireclass 508.032.731FC Fireclass Essential 4 Zone PanelThe Fireclass Essential Panel range is an EN-approved low cost conventional panels that are available in both 2 Zone and 4 Zone variants. The panels can support up to 128 devices with a maximum of 32 devices on each zone. The panels are approved to EN 54-2 EN 54-4 and listed as part of the EN 54-13 system certificate.The panel UI has the following features18 LEDs on the 2 Zone Panel and 22 LEDs on the 4 Zone PanelOne piezo buzzer for audible indicationEight push buttons for user inputsKey FeaturesModern and aesthetic designSurface mountableOption to set delays for outputs during alarmButtons for silence resound and resetTwo open collector outputsDisable feature for sounders and zonesVolt-free fire and fault relaysTest feature for installationTwo auxiliary inputs alert input and class change inputSupport for all FireClass 600 and 700 series conventional detectors conventional sounders and VADsSupport for third party devicesPlease note For full details on all the supported devices refer to the EN 54-13 certificate.Fully compliant with EN 54-2 EN 54-4 and is listed as part of the EN 54-13 system certificatePlease note The image is for illustrative purposes only. Please refer to product description.

GBP 213.90

1

Fireclass 557.202.082FC BACnet UC-8112-ME-T-LX Interface with CBL-F9DPF1x4-BK-100

Fireclass 557.202.082FC BACnet UC-8112-ME-T-LX Interface with CBL-F9DPF1x4-BK-100The 557.202.082FC is a BACnet UC-8112-ME-T-LX Interface with CBL-F9DPF1x4-BK-100.BACnet can be provided from a stand-alone Fireclass panel or from an Fireclass network via the BACnet converter.The BACnet converter is a mini RISC-based embedded computer which converts fire data to the BACnet communications protocol. The converter needs special firmware that is simply uploaded from a PC.BACnet is an industry standard communications protocol for building automation and control networks. It was designed to allow communication of building automation and control systems for applications such as heating ventilating and air-conditioning control lighting control access control and fire detection systems and their associated equipment.The BACnet protocol provides mechanisms for computerised building automation devices to exchange information regardless of the particular building service they perform.Key FeaturesHigh level interface to building automation systemsMeet interfacing requirements for large integrated projects

GBP 1548.76

1

Fireclass 557.180.423FC TM520 Timer Module Non-Addressable

Fireclass 557.180.423FC TM520 Timer Module Non-AddressableThe TM520 provides an output that can be activated based on a delay time. If either the key-switch on the module is activated or a predefined event within the control panel occurs then a times delay set between 10 minutes and 21 hours 10 minutes is started. When the delay reaches zero the TM520 output is activated. The unit sounds an internal buzzer and shows a red LED when the output is active and shows a yellow LED when the timer is counting down. To provide a warning the delay is nearly over the red LED and the buzzer will pulse 5 minutes before the end of the delay.The TM520 requires a separate 24Vd.c. supply to operate. The module is not addressable and will therefore not take an address on the loop.Key FeaturesEN54 -13 approvedRequires separate24Vd.c. power supply

GBP 130.00

1

Fireclass 516.016.017FC ProReact Analogue Controller - Includes One EOL Unit

Fireclass 516.016.017FC ProReact Analogue Controller - Includes One EOL UnitProReact Analogue Heat Detector system consists of a control module and four core detection cable designed to interface to a conventional fire alarm panel or DIM800 or DDM800 addressable module. The control module monitors the resistance of specially doped polymers within the sensor cable which change as a function of temperature. An abnormal change in resistance along the detection cable triggers either a Pre- Alarm or Alarm on the interface module.The system is intended to simplify system design and be uncomplicated and straightforward to install. Commissioning of the controller can be done using a laptop computer or through an optional built-in self-programming module. The sensor cable has been designed to be physically and electronically rugged to suite a range of environments with options for PVC Polypropylene or Nylon coatings or a strong stainless steel braid. The ProReact technology offers an alternative solution to heat protection in a wide range of applications and industries from power generation to oil and gas.Typical applicationsCar parksFactories processing plantsWarehousesCable traysConveyor beltsKey FeaturesAlarm Pre-Alarm temperature ranges from 54-100CProgrammable on-site adjustment of sensitivityUp to 500 m continuous lengthAlarm hot-spot length equal to 3 of zone lengthSeparate Alarm and Pre-alarm volt-free outputsNo nomograms or other scales to interpretSimple 3-Step InstallationAmbient temperature compensation maintains alarm temperature accuracySelf-Restorable after fire event up to 125CFlexible cable for easy mechanical installationReliable signalling of open and short circuit conditionsExtrusion and Braiding options to satisfy both mechanical and environmental conditions

GBP 539.69

1

Fireclass 516.016.016FC ProReact Analogue Controller with Display

Fireclass 516.016.016FC ProReact Analogue Controller with DisplayProReact Analogue Heat Detector system consists of a control module and four core detection cable designed to interface to a conventional fire alarm panel or DIM800 or DDM800 addressable module. The control module monitors the resistance of specially doped polymers within the sensor cable which change as a function of temperature. An abnormal change in resistance along the detection cable triggers either a Pre- Alarm or Alarm on the interface module.The system is intended to simplify system design and be uncomplicated and straightforward to install. Commissioning of the controller can be done using a laptop computer or through an optional built-in self-programming module. The sensor cable has been designed to be physically and electronically rugged to suite a range of environments with options for PVC Polypropylene or Nylon coatings or a strong stainless steel braid.The ProReact technology offers an alternative solution to heat protection in a wide range of applications and industries from power generation to oil and gas.Typical applicationsCar parksFactories processing plantsWarehousesCable traysConveyor beltsKey FeaturesAlarm Pre-Alarm temperature ranges from 54-100CProgrammable on-site adjustment of sensitivityUp to 500 m continuous lengthAlarm hot-spot length equal to 3 of zone lengthSeparate Alarm and Pre-alarm volt-free outputsNo nomograms or other scales to interpretSimple 3-Step InstallationAmbient temperature compensation maintains alarm temperature accuracySelf-Restorable after fire event up to 125CFlexible cable for easy mechanical installationReliable signalling of open and short circuit conditionsExtrusion and Braiding options to satisfy both mechanical and environmental conditions

GBP 650.09

1

Awardvindende Google Marketing Powerhouse

Brand

Merchant