step in hundesele from GBP 9 | See the cheapest prices and offers on css.lazzaweb.dk

Fireclass 517.050.511FC Detector Cover amp Base in Matt Black - Pack of 10

Fireclass 517.050.511FC Detector Cover Base in Matt Black - Pack of 10Detectors and bases are supplied white as standard but a range of alternative colours are also available. The Matt Black version is supplied as standard in packs of ten detector covers and 4B-C Continuity bases.Key FeaturesPack of 10Colour Matt Black

GBP 165.38

1

Fireclass 568.800.034FC HVR800 High Voltage Relay Module In D800 Housing

Fireclass 568.800.034FC HVR800 High Voltage Relay Module In D800 HousingThe HVR800 is a non-addressable device designed to allow a low current main rated relay to switch up to 10A. Alternatively a low voltage drive signal such as that provided by the RIM800 or 80 way mimic can be used to switch the integral mains relay.Key FeaturesD800 housing- 5 A 240 VacDimensions WxHxD 42x26.5x74 mmOperating Temperature -25 to 70 CStorage Temperature -45 to 80 CRelative Humidity 95 non-condensing

GBP 90.48

1

Fireclass 516.016.017FC ProReact Analogue Controller - Includes One EOL Unit

Fireclass 516.016.017FC ProReact Analogue Controller - Includes One EOL UnitProReact Analogue Heat Detector system consists of a control module and four core detection cable designed to interface to a conventional fire alarm panel or DIM800 or DDM800 addressable module. The control module monitors the resistance of specially doped polymers within the sensor cable which change as a function of temperature. An abnormal change in resistance along the detection cable triggers either a Pre- Alarm or Alarm on the interface module.The system is intended to simplify system design and be uncomplicated and straightforward to install. Commissioning of the controller can be done using a laptop computer or through an optional built-in self-programming module. The sensor cable has been designed to be physically and electronically rugged to suite a range of environments with options for PVC Polypropylene or Nylon coatings or a strong stainless steel braid. The ProReact technology offers an alternative solution to heat protection in a wide range of applications and industries from power generation to oil and gas.Typical applicationsCar parksFactories processing plantsWarehousesCable traysConveyor beltsKey FeaturesAlarm Pre-Alarm temperature ranges from 54-100CProgrammable on-site adjustment of sensitivityUp to 500 m continuous lengthAlarm hot-spot length equal to 3 of zone lengthSeparate Alarm and Pre-alarm volt-free outputsNo nomograms or other scales to interpretSimple 3-Step InstallationAmbient temperature compensation maintains alarm temperature accuracySelf-Restorable after fire event up to 125CFlexible cable for easy mechanical installationReliable signalling of open and short circuit conditionsExtrusion and Braiding options to satisfy both mechanical and environmental conditions

GBP 539.69

1

Fireclass 516.016.016FC ProReact Analogue Controller with Display

Fireclass 516.016.016FC ProReact Analogue Controller with DisplayProReact Analogue Heat Detector system consists of a control module and four core detection cable designed to interface to a conventional fire alarm panel or DIM800 or DDM800 addressable module. The control module monitors the resistance of specially doped polymers within the sensor cable which change as a function of temperature. An abnormal change in resistance along the detection cable triggers either a Pre- Alarm or Alarm on the interface module.The system is intended to simplify system design and be uncomplicated and straightforward to install. Commissioning of the controller can be done using a laptop computer or through an optional built-in self-programming module. The sensor cable has been designed to be physically and electronically rugged to suite a range of environments with options for PVC Polypropylene or Nylon coatings or a strong stainless steel braid.The ProReact technology offers an alternative solution to heat protection in a wide range of applications and industries from power generation to oil and gas.Typical applicationsCar parksFactories processing plantsWarehousesCable traysConveyor beltsKey FeaturesAlarm Pre-Alarm temperature ranges from 54-100CProgrammable on-site adjustment of sensitivityUp to 500 m continuous lengthAlarm hot-spot length equal to 3 of zone lengthSeparate Alarm and Pre-alarm volt-free outputsNo nomograms or other scales to interpretSimple 3-Step InstallationAmbient temperature compensation maintains alarm temperature accuracySelf-Restorable after fire event up to 125CFlexible cable for easy mechanical installationReliable signalling of open and short circuit conditionsExtrusion and Braiding options to satisfy both mechanical and environmental conditions

GBP 650.09

1

Fireclass 516.016.156FC ProReact EN Analogue End of Line Unit

Fireclass 516.016.156FC ProReact EN Analogue End of Line UnitThe ProReact EN Analogue End-of-line Unit is compulsory in all ProReact EN Analogue LHD systems as it has a key role in the operation of the technology allowing the control unit to detect a short circuit or open circuit in the sensor cable. It is small in size and is straightforward to be mounted on surfaces.Typical ApplicationsCar parksFactories and processing plantsWarehousesCable traysConveyor beltsData centres

GBP 73.60

1

Fireclass 516.016.028FC LHD Junction EOL Box

Fireclass 516.016.028FC LHD Junction EOL BoxThe ProReact Digital End-of-Line Unit is designed to effectively terminate up-to two zones of ProReact EN Digital LHD cable in a secure weatherproof enclosure.Furthermore the built-in switches for testing a fault and alarm condition allow the integrity of the whole system to be functionally checked in situ providing comprehensive testing and maintenance of the system.Typical ApplicationsCar parksOil and gas tank farmsMinesCable traysCold storageConveyor beltsKey FeaturesWeatherproof enclosureBuilt-in switchesThe first digital linear heat detection system to be certified to EN54-282016Improved testing and maintenance functionalityManufactured in the UK

GBP 73.60

1

Fireclass 516.016.029FC Digital One or Two Zone LHD EOL Box

Fireclass 516.016.029FC Digital One or Two Zone LHD EOL BoxThe 516.016.029FC is a ProReact Digital One or Two Zone LHD EOL Box. It is designed to effectively terminate up-to two zones of ProReact EN Digital LHD cable in a secure weatherproof enclosure.Furthermore the built-in switches for testing a fault and alarm condition allow the integrity of the whole system to be functionally checked in situ providing comprehensive testing and maintenance of the system.Key FeaturesWeatherproof enclosureBuilt-in switches

GBP 122.65

1

Fireclass 516.016.018FC ProReact Analogue End Of Line Unit

Fireclass 516.016.018FC ProReact Analogue End Of Line UnitProReact EN Analogue End-of-line Unit is compulsory in all ProReact EN Analogue LHD systems as it has a key role in the operation of the technology allowing the control unit to detect a short circuit or open circuit in the sensor cable. It is small in size and is straightforward to be mounted on surfaces.Thermocables ProReact Digital End-of-line Unit with test facility has also been certified to EN54-282016 and enables users to undertake hassle-free functional testing of the system. Users can verify normal conditions trouble and alarm functions of a system by simulating a break in the cable or overheat condition.The ProReact technology offers an alternative solution to heat protection in a wide range of applications and industries from power generation to oil and gas. It is a cost-effective resettable and can be used in applications that are less suited to other types of fire detectors. The ProReact EN Analogue LHD system has a wide range of available alarm temperatures to suit different environments.Key FeaturesFor use with the ProReact Analogue ControllerSmall sizeImproved testing and maintenance functionalityManufactured in the UK

GBP 61.33

1

Fireclass JCCT-01-25FC Condensation Trap - 25mm Red

Fireclass JCCT-01-25FC Condensation Trap - 25mm RedUsed in an environment where there are constant temperature changes which causes condensation in the system typically in a chill store or a room that is open to the atmosphere which can be be measured and recorded.It can be drained on a regular basis by simply opening the valve.Key FeaturesFitting colour RedPipe colour Opaque

GBP 93.31

1

Fireclass 516.016.230FC ProReact Dual Height L Clip - Stainless Steel Pack of 100

Fireclass 516.016.230FC ProReact Dual Height L Clip - Stainless Steel Pack of 100The 516.016.230FC is a ProReact Dual L Clip in stainless steel.The ProReact Zintec and Stainless Steel clips have been specifically chosen to comply with the latest requirements detailed in BS 5839-1.Key FeaturesMaterial Stainless SteelSpecification 100mm x 20 mm with 3 mounting holes for multiple cables andor options in mounting heightOperating Temperature up to 815CPack of 100

GBP 178.80

1

Fireclass 517.025.061FC DPK6-MB - Duct Probe Mounting Bracket

Fireclass 517.025.061FC DPK6-MB - Duct Probe Mounting BracketThe 517.025.061FC is a Mounting Bracket designed for use with the DPK6 Duct Probe.The DPK6 duct probe units have been developed to detect smoke in ventilation ducts and offer significant benefits in terms of performance and installation.Key FeaturesMounting Bracket

GBP 25.34

1

Fireclass 516.052.041.YFC MD611Ex Conventional Fixed Temperature Heat Detector

Fireclass 516.052.041.YFC MD611Ex Conventional Fixed Temperature Heat DetectorThe MD611Ex intrinsically safe detector uses two networked thermistors in a bridge configuration to provide a fast response that depends both on absolute temperature and rate of rise of temperature.This type of sensor reacts to abnormally high rates of change of temperature and provides the fastest response over a wide range of ambient temperatures. A fixed temperature limit is also incorporated in these detectors. In many environments e.g. kitchens and boiler rooms sudden large changes in temperature are considered normal. Rate-of-rise detectors are generally not suitable in these cases and fixed temperature static types should be used.The MD611Ex detectors are designed to comply with EN 50 014 and EN 50 020 for intrinsically safe apparatus and are certifiedATEX Code Ex II 1GCenelec Code EEx ia IIC T5Key FeaturesIntelligent Universal SmokeHeatCO detectorLow profile discreet and unobtrusiveSuperior performance and reliabilityDesigned for fast easy installationOptional locking kitMay be used in systems that meet BS5839 Pt 1Integral and remote alarm LEDCertified to ATEX Ex II 1GD and Cenelec Ex ia IIC T5Ex iaD 20 T100oCComplies to EN54-7 for Smoke Detectors and EN54-5 for Heat Detectors

GBP 76.01

1

Fireclass 516.052.051.YFC MD601Ex Conventional Rate of Rise Heat Detector

Fireclass 516.052.051.YFC MD601Ex Conventional Rate of Rise Heat DetectorThe MD601Ex intrinsically safe detector uses two networked thermistors in a bridge configuration to provide a fast response that depends both on absolute temperature and rate of rise of temperature.This type of sensor reacts to abnormally high rates of change of temperature and provides the fastest response over a wide range of ambient temperatures. A fixed temperature limit is also incorporated in these detectors. In many environments e.g. kitchens and boiler rooms sudden large changes in temperature are considered normal. Rate-of-rise detectors are generally not suitable in these cases and fixed temperature static types should be used.The MD601Ex detectors are designed to comply with EN 50 014 and EN 50 020 for intrinsically safe apparatus and are certified to ATEX Code Ex II 1G and Cenelec Code EEx ia IIC T5.Key FeaturesIntelligent Universal SmokeHeatCO detectorLow profile discreet and unobtrusiveSuperior performance and reliabilityDesigned for fast easy installationOptional locking kitMay be used in systems that meet BS5839 Pt 1Integral and remote alarm LEDCertified to ATEX Ex II 1GD and Cenelec Ex ia IIC T5Ex iaD 20 T100oCComplies to EN54-7 for Smoke Detectors and EN54-5 for Heat Detectors

GBP 71.02

1

Fireclass 516.900.001FC 701P Conventional Optical Detector

Fireclass 516.900.001FC 701P Conventional Optical DetectorThe 701P is a conventional optical smoke detector ideal for use with the Tyco FireClass range of conventional fire alarm control panels.The 701P Smoke Detector operates by sensing the optical scatter from smoke particles generated in a fire. These detectors are suitable for general applications and areas where cable overheating may occur for example in electrical services areas.The 700 Series Intelligent Conventional Fire Detection Range is the first conventional detector range from Johnson Controls that uses algorithms to determine fire conditions more precisely. This provides superior performance and improved false alarm rejection rates.Through innovative design the built-in micro-processors in the 700 Series detectors offer built-in drift compensation which extends the life of the detectors thereby reducing service costs to the customers. Installers only need one fitting to complete the installation.The 701PH Detector has EN54-29 approval.Key FeaturesDesigned for fast easy installationLow operational voltageAvailable as smoke fixed heat RoR heat and photo heatBackward compatibility with 600 seriesCompatible with 4B-D 4B and 5B basesLow profile and discreet designApproval to EN54 LPCB standardsImproved detection algorithmsBuilt-in drift compensationEN54 approval

GBP 10.27

1

Fireclass 557.202.708FC FC410MIM Fixing Kit for FireClass 1.9A7Ah PSUs

Fireclass 557.202.708FC FC410MIM Fixing Kit for FireClass 1.9A7Ah PSUsThe 557.202.708FC is a FC410MIM Addressable Mini Input Module and Fixing Kit designed for the Fireclass 1.9A7Ah Power Supply Units.The FC410MIM Mini Input module is designed to monitor fire contacts in extinguishing system control ventilation control fire door control etc. It is built for fitting in small devices that is required to be monitored for fire fault or warning.The module provides one identifiable detection spur which is capable of monitoring multiple normally open contacts or a single normally closed contact. The module can be mounted in any electrical enclosure with sufficient depth to accommodate it and the contacts monitored by the IN and IN- terminals. The remote LED if required not supplied must be located within the same electrical enclosure.Key FeaturesSupplied with fixing kitDesigned for us withFireclass 1.9A7Ah Power Supply UnitsSmall sizeOperating voltage 20 40V dcRelative Humidity Up to 95RH monitor100 OhmEnd Of Line Monitor Value 200 Ohm

GBP 95.87

1

Fireclass 601CH Conventional Enhanced Carbon Monoxide Detector

Fireclass 601CH Conventional Enhanced Carbon Monoxide DetectorThe 601CH detector forms part of the series 600 range of plug in detectors for ceiling mounting. 601CH have a fast response in fire detection are tolerant in positioning and can be mounted in locations where there are likely to be obstacles to free smoke plume movement. These detectors are particularly well suited to sleeping risk storage areas and applications where smoke detectors are prone to false alarm.Incorporation of A1R rate of rise heat detector within the 601CH provides extra non-selectable detection modes which allows the detectors to operate in a wide variety of applications where combined risk mean that CO detection alone would be insufficient. The integrated rate of rise detector acts as a normal heat detector additionally enhancing the sensitivity of the carbon monoxide detector if a rapid change of temperature is detected by the detector thermistor.Key FeaturesLow profile discreet and unobtrusiveSuperior performance and reliabilityDesigned for fast easy installationIntegral and remote alarm LEDSeries of product approvals

GBP 45.36

1

Fireclass LPB24-A-TFC LED 24V Strobe Amber Lens

Fireclass LPB24-A-TFC LED 24V Strobe Amber LensFireclass offer a range of low-profile LED beacons with a variety of lens colour and mounting options available in either 12V dc or 24V dc models.It is suitable for use in fire intruder access control systems or general applications.Key FeaturesUses efficient LED technologyLow profile design 44mmSingle stud or twin thread mount optionsLow current operationMaximum light intensity and dispersionCompatible with a wide range of systemsIP66 ratedFresnel LensPolycarbonate and ABS constructionSuitable for use in fire intruder access control systems or general applications

GBP 8.88

1

Fireclass 516.800.909FC 801HL Remote Indicator

Fireclass 516.800.909FC 801HL Remote IndicatorThe 801HL Remote Indicator is used where a detector LED is not visible i.e. when the detector is mounted in a roof void lift shaft etc. The 800HL remote indicator lamp provides a larger indicator for use in place of the RIL when longer distances are involved or in VdS influenced markets.It is typically used to indicate the source of an alarm in buildings with long corridors e.g. hotels hospitals and apartments. The 801HL can be mounted to any suitable flat surface and has fixing centres at 60 and 80mm.Key FeaturesProtocol UniversalOperating Temp -20C to 70CRelative Humidity Up to 95 RHStorage Temperature -45 to 80 CCurrent consumption Standby 0 Alarm 5 mAHigh Intensity red LEDsMonitors up to four detectorsAssembly Dimensons 85 x 85 x 38 mmAlarm 5mAWire Size 1.5mm2 max

GBP 12.22

1

Fireclass 557.200.710FC FC64 DC Repeater 64 Zones

Fireclass 557.200.710FC FC64 DC Repeater 64 ZonesThe FC64RD Addressable fire alarm repeater panel is fully functioning and is compatible with the FC32 and FC64 range of fire alarm panels.Fire detection in big buildings can be extremely difficult. The FC64RD Compact addressable fire alarm zone repeater panel ensures that getting in to a fire alarm system and being able to interrogate the fire panel never needs to be difficult again.In an office building fire detection control panels may be located in reception but require numerous fire repeater panels around the building or on different floors.In schools the main fire alarm panel may be in the office but repeater panels are required around the school or at a security guard or caretakers house.The 24v FireClass Fire Alarm repeater panels also come in at just 4kg and provide a super compact repeater which is both aesthetically pleasing as well as retaining all the features and functions of the FireClass FC32 and FC64 addressable fire alarm control panels.The FireClass addressable repeater panel unit shows the same information as the main fire alarm control panel retains the full functionality of the main addressable fire alarm control panel including the ability to dial in to any other panel on the network to view and configure any point on the panel including RBus points.The FireClass repeater panel is almost half the depth and width of the larger repeater panels and also 22 shorter in height.Key FeaturesH x W x D 370 x 254 x 84 mmUp to 1000 addresses available on fire alarm control panel640 Character DisplayPermanently displays system statusDisplays temperature Carbon Monoxide CO level and smoke level at point in fire alarmViewing 3000 event logManual and Automatic walk test and reporting functionsAutomatic battery testFire Detector service functionsFront control panel controls enabling text and configuration changes Up to 24 panels networkableChoice of up to 5 fully functional repeaters with a maximum of 7 per panelWorks in conjunction with our Fireclass Addressable 64 Zone Control Panel

GBP 948.79

1

Fireclass 517.001.304FC MTL5525 IS Sounder Driver

Fireclass 517.001.304FC MTL5525 IS Sounder DriverThe MTL5525 Isolating Sounder Driver enables an intrinsically safe sounder located in the hazardous area to be controlled from the safe area.The barrier is designed as a CE marked replacement for the existing MTL3021 barrier. It has one channel and is suitable for connecting loads in Zone 0 IIC T4-T6 hazardous areas if suitably certified. It enables an onoff device in a hazardous area to be controlled by a volt-free contact or logic signal in the safe area. It can drive loads such as solenoids alarms LEDs and other low power devices that are certified as intrinsically safe or are classified as nonenergy storing simple apparatus.MTL5500 Series isolating IS interface units offer a compact and easy-to-use means for communicating safely with process measuring indicating actuating and local control equipment in hazardous areas. The range of models handle analogue and binary signals in both directions amplifying or otherwise conditioning them as required and at the same time providing certified explosion protection for equipment and wiring in all zones and all explosive atmospheres. The range has been designed for reliability. It builds on the proven success of the MTL2000 3000 4000 and 5000 Series to bring the benefits of new developments in galvanic isolation without compromising the reliability of the designs from which it has evolved. It is designed from the outset to meet all relevant European Directives. Uniform appearance and connectability of the units and a comprehensive range of accessories and enclosures make planning a pleasure for the user.Key FeaturesInput Type VoltageOutput Type VoltageSignal Conditioner Type IsolationInput Range 1.4 - 4.5 V dcOutput Range 7.8 - 24 VMounting Type DIN RailMinimum Operating Temperature -20CMaximum Operating Temperature 60CNumber of Channels 1Module Type SolenoidAlarm DriverTermination CableOperating Temperature Range -20 - 60 CSeries MTL5000

GBP 213.74

1

Fireclass 516.900.004FC 702H Conventional Fixed Temp Heat Detector - 60C EN

Fireclass 516.900.004FC 702H Conventional Fixed Temp Heat Detector - 60C ENThe Fireclass 702H is a conventional fixed temperature detector ideal for use with the Fireclass range of conventional fire alarm control panels.The 700 Series Intelligent Conventional Fire Detection Range is the first conventional detector range from Johnson Controls that uses algorithms to determine fire conditions more precisely. This provides superior performance and improved false alarm rejection rates.Through innovative design the built-in micro-processors in the 700 Series detectors offer built-in drift compensation which extends the life of the detectors thereby reducing service costs to the customers. Installers only need one fitting to complete the installation.Key FeaturesDesigned for fast easy installationLow operational voltageBackward compatibility with 600 seriesCompatible with 4B-D 4B and 5B basesLow profile and discreet designApproval to EN54 LPCB standardsImproved detection algorithmsBuilt-in drift compensationMicroprocessor based threshold compensationImproved detection algorithmsEN54 approval

GBP 9.47

1

Fireclass 516.900.005FC 703H Conventional Fixed Temp Heat Detector - 90C EN

Fireclass 516.900.005FC 703H Conventional Fixed Temp Heat Detector - 90C ENThe Fireclass 703H is a conventional fixed temperature detector ideal for use with the Fireclass range of conventional fire alarm control panels.The 700 Series Intelligent Conventional Fire Detection Range is the first conventional detector range from Johnson Controls that uses algorithms to determine fire conditions more precisely. This provides superior performance and improved false alarm rejection rates.Through innovative design the built-in micro-processors in the 700 Series detectors offer built-in drift compensation which extends the life of the detectors thereby reducing service costs to the customers. Installers only need one fitting to complete the installation.Key FeaturesDesigned for fast easy installationLow operational voltageBackward compatibility with 600 seriesCompatible with 4B-D 4B and 5B basesLow profile and discreet designApproval to EN54 LPCB standardsImproved detection algorithmsBuilt-in drift compensationMicroprocessor based threshold compensationImproved detection algorithmsEN54 approval

GBP 9.65

1

Fireclass 516.016.231FC ProReact Standard L Clip - 50mm - Stainless Steel Pack of 100

Fireclass 516.016.231FC ProReact Standard L Clip - 50mm - Stainless Steel Pack of 100The 516.016.231FC is a ProReact Standard L Clip in stainless steel.The ProReact Zintec and Stainless Steel clips have been specifically chosen to comply with the latest requirements detailed in BS 5839-1.Key FeaturesMaterial Stainless SteelSpecification 50mm x 20mm with 1 mounting holeOperating Temperature up to 815CPack of 10

GBP 204.50

1

Fireclass 517.001.302FC MTL5561 2 Channel Galvanic Isolator

Fireclass 517.001.302FC MTL5561 2 Channel Galvanic IsolatorThe MTL5561 is a loop-powered 2channel interface for use with conventional fire and smoke detectors located in hazardous areas. In operation the triggering of a detector causes a corresponding change in the safearea current. The unit features reverse input polarity protection while no-fail earth fault detection on either line can be provided by connecting an earth leakage detector to terminal 3 andor 6. This galvanic isolator is CE marked and replaces the MTL3043 barrier option. It is suitable for connecting loads in Zone 0 IIC T4-T6 hazardous areas if suitably certified.The MTL5500 range of isolators provide intrinsically safe IS communication and signal conditioning for a wide range of hazardous-area devices. Total AC and DC isolation exists between input output and power supply on separately powered units and between input and output on loop-powered units. No IS earth is required. DIN-rail mounting and plug-in signal and power connectors simplify installation and maintenance.Key FeaturesBarrier Type GalvanicNumber of Channels 2Supply Voltage 6 - 30 V dcSafety Voltage Maximum 28 VSafety Current Maximum 42mASignal Type AnalogueMinimum Operating Temperature -20CMaximum Operating Temperature 60COperating Temperature Range -20 - 60 CHazardous Area Certification ATEX

GBP 267.71

1

Fireclass 516.900.003FC 701H Conventional Rate of Rise Heat Detector - 60C EN

Fireclass 516.900.003FC 701H Conventional Rate of Rise Heat Detector - 60C ENThe Fireclass 701H is a conventional rate of rise heat detector ideal for use with the Fireclass range of conventional fire alarm control panels.The 700 Series Intelligent Conventional Fire Detection Range is the first conventional detector range from Johnson Controls that uses algorithms to determine fire conditions more precisely. This provides superior performance and improved false alarm rejection rates.Through innovative design the built-in micro-processors in the 700 Series detectors offer built-in drift compensation which extends the life of the detectors thereby reducing service costs to the customers. Installers only need one fitting to complete the installation.Key FeaturesDesigned for fast easy installationLow operational voltageBackward compatibility with 600 seriesCompatible with 4B-D 4B and 5B basesLow profile and discreet designApproval to EN54 LPCB standardsImproved detection algorithmsBuilt-in drift compensationMicroprocessor based threshold compensationImproved detection algorithmsEN54 approval

GBP 9.32

1

Awardvindende Google Marketing Powerhouse

Brand

Merchant

Price (EUR)