receiver controlled switch from GBP 21 | See the cheapest prices and offers on css.lazzaweb.dk

Gent S4-34741-99 Light Shields for Beam Receiver Pack of 5

Gent S4-34741-99 Light Shields for Beam Receiver Pack of 5The S4-34741-99 is a pack of Light Shields for Beam Receivers.A light shield is only required to be fitted onto a beam receiver where direct sunlight or strong light is likely to fall in the path of the beam receiver. Where necessary fit the light shield.Gent by Honeywells S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.Powered and controlled via the loop the beam is a market leading device with features such as one-man alignment and commissioning which is achieved using the auto gain setting this ensure the optimum alignment is reached.Maintenance of the beam is enhanced with a key operated test feature which simulates the obscuration of the beam in a fire. The Gent loop powered beam is certified to EN54 parts 12 and 17.Key FeaturesPack of 5Prevent strong light from interfering with beam receiver

GBP 105.31

1

Gent S4-34742 Beam Sensor Receiver

Gent S4-34742 Beam Sensor ReceiverThe Gent 34742 is a beam sensor detector receiver for use with the Gent 34741 beam detector transmitter.Vigilons loop powered technology allows up to 16 beam pairs to be connected to the same loop circuit each covering a distance of up to 100m without the need for an external Power Supply Unit wiring or interfacing.Compatible with the full range of Vigilon and Nano control panels the S-Quad beam uses the panel software to ensure a fast response to fi re while offering software filters to reduce the number of unwanted alarmsWhat is a Beam SensorA beam sensor works when theemittersends out abeamof light most often a pulsed infrared visible red or laser that diffuses in all directions filling a detection area. The target then enters the area and deflects part of thebeamback to the receiver.If anything is detected it will signal an alarm.Key FeaturesFor Use With S4-34741

GBP 755.02

1

Gent S4-34740 Beam Sensor Pair Transmitter and Receiver Excluding Bracket and Base

Gent S4-34740 Beam Sensor Pair Transmitter and Receiver Excluding Bracket and BaseGent S4-34740 S-Quad Addressable Loop Powered Beam Sensor Pair provides an enhanced solution for linear beam detection for applications where Gent S4 Vigilon point detection is either not practical or economic.Powered and controlled via the loop the beam is a market leading device with features such as one man alignment and commissioning which is achieved using the auto gain setting this ensure the optimum alignment is reached.Maintenance of the beam is enhanced with a key operated test feature which simulates the obscuration of the beam in a fire.The Gent loop powered beam is certified to EN54 parts 12 and 17. Compatible with the full range of Vigilon and Nano control panels the S-Quad beam uses the panel software to ensure a fast response to fire while offering software filters to reduce the number of unwanted alarms.Key FeaturesS-Quad Beam pairs are loop powered supporting 16 pairs per loopEach beam can be set to one of 6 sensitivity states to provide a best fit for individual applicationsThe beam provides increased resilience to interference from the sun and other light sourcesRemote key switch provides test facility at ground level without the need to gain access to beams mounted in high areasThe beam incorporates an LED array to indicate signal strength allowing accurate alignment during one person commissioningOptimum sensitivity is maintained by automatic gain setting triggered at the beam during alignmentThe optical lens design is intended to minimise build-up of dust to reduce the maintenance and cleaning requiredThe S-Quad beam is compatible with early versions of the Vigilon Beam using the S-Quad programming base avoiding the need to upgrade to latest control software

GBP 871.37

1

Gent S4-34499 Set of Keys for Key Switch Interface and MCP 1 Set 2 Keys

Gent S4-34499 Set of Keys for Key Switch Interface and MCP 1 Set 2 KeysThe S4-34499 is a set of 2 spare keys for the S4-34418 Key-Switch Interface and S4-34807 Key-Switch Call Point.

GBP 37.88

1

Gent 704952 Yellow Fascia for Key Switch MCP For Use With S4-34807

Gent 704952 Yellow Fascia for Key Switch MCP For Use With S4-34807The Gent 704952 is a Fascia designed for use with the Gent S4-34807 Vigilon Key-Switch Call Point.Key FeaturesComes in the colour yellowFlat designPlug-in connection terminalsOptional terminalTriple key function test open reset

GBP 36.61

1

Gent 704982 Yellow Surface Mount Back Box for Key Switch MCP For Use With S4-34807

Gent 704982 Yellow Surface Mount Back Box for Key Switch MCP For Use With S4-34807The 704982 is a Surface Mount Back Box designed for use with the Gent S4-34807 Vigilon Key-Switch Call Point.Key FeaturesComes in the colour yellowFlat designPlug-in connection terminalsOptional terminalTriple key function test open reset

GBP 21.16

1

Gent Vigilon Key-Switch Call Point - S4-34807

Gent Vigilon Key-Switch Call Point - S4-34807The S4-34807 Vigilon Key Switch Manual Call Point is a key operated manual call point to be used with the Vigilon and Nano system where break glass models are prone to unauthorised activation. The call point is easy to install and can be mounted on a standard recessed single back box or bespoke red back boxes for surface mounting.The call point is continuously monitored to ensure a trigger is responded to in less than 3 seconds system wide.Key FeaturesDesigned for use with Vigilon and Nano systemsKey operatedPrevents unauthorised activationEasy to installEN54 part 11 17 compliantKey included

GBP 141.83

1

Gent S4-34418 Key Switch Interface Single Channel cw Blue Enclosure

Gent S4-34418 Key Switch Interface Single Channel Comes With Blue EnclosureThe S4-34418 from Gent is a Key-Switch Interface Single Channel which comes with a blue enclosure.Vigilon can accommodate a high quantity of loop powered interface units offering fexible range of inputs and outputs from the FDA system from plant control and signalling other systems in a fi re to linking with other emergency management systems such as sprinklers or security systems.Loop powered interfaces offer a cost effective solution with each device individually addressed increasing the overal management capability of the FDA system.Interfaces are either powered from the loop or require a separate mains supply. The mains power version has its own battery backup.Key FeaturesComes with blue enclosureSingle channel

GBP 136.74

1

Gent S4-34412 12 Input Interface Module Supervisory Inputs Only

Gent S4-34412 12 Input Interface Module Supervisory Inputs OnlyThe S4-32212 module has been designed to be installed in custom panel to provide supervisory input to control plant via Vigilon System. The module connects to a loop circuit of a Vigilon fire alarm control panel. It uses one of 200 device addresses on the loop and responds to regular polls from the control panel reporting the device type and the status of its supervisory switch inputs.The module is supplied with a 26-way ribbon cable for connecting to a Connector converter that holds the terminals for external input switches and corresponding confirmation LEDs for each switch.

GBP 211.48

1

Gent S4-34741-50 Obscuration Test Card Set

Gent S4-34741-50 Obscuration Test Card SetThe S4-34741-50 is an Obscuration Test Card Set designed for use with Gent Beam Detectors.Honeywell Gents S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.Powered and controlled via the loop the beam is a market leading device with features such as one man alignment and commissioning which is achieved using the auto gain setting this ensure the optimum alignment is reached.Maintenance of the beam is enhanced with a key operated test feature which simulates the obscuration of the beam in a fire. The Gent loop powered beam is certified to EN54 parts 12 and 17.Key FeaturesS-Quad Beam pairs are loop powered supporting 16 pairs per loopEach beam can be set to one of 6 sensitivity states to provide a best fi t for individual applicationsThe beam provides increased resilience to interference from the sun and other light sourcesRemote key switch provides test facility at ground level without the need to gain access to beams mounted in high areasThe beam incorporates an LED array to indicate signal strength allowing accurate alignment during one person commissioningOptimum sensitivity is maintained by automatic gain setting triggered at the beam during alignmentThe optical lens design is intended to minimise build-up of dust to reduce the maintenance and cleaning requiredThe S-Quad beam is compatible with early versions of the Vigilon Beam using the S-Quad programming base avoiding the need to upgrade to latest control software

GBP 32.03

1

Gent S4-34741-03 34740 Parallel Bracket and Base

Gent S4-34741-03 34740 Parallel Bracket and BaseTheS4-34741-03 is a Parallel Bracket and Base for standard applications adjustable to - 15.Gents S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.Powered and controlled via the loop the beam is a market leading device with features such as one man alignment and commissioning which is achieved using the auto gain setting this ensure the optimum alignment is reached.Maintenance of the beam is enhanced with a key operated test feature which simulates the obscuration of the beam in a fire. The Gent loop powered beam is certified to EN54 parts 12 and 1.Key FeaturesMulti angle fittingSupplied with baseSimple alignment

GBP 73.88

1

Gent 585050 Power Supply 1U - 24VDC 190A

Gent 585050 Power Supply 1U - 24VDC 190AThe Gent 585050 is an EN54-4 certified backup power supply unit. Designed with double conversion input and output voltage 230 V 50 Hz single-phase available power 1.6KW 2 KVA and 800W1KVA at Cos.phi. 0.8 static switch RS232 and USB and EPO emergency shutdown fitted as standard complete with anomaly signal output board.Key FeaturesEN54-4 CertifiedInput and output voltage 230 V 50 HzPower 1.6KW 2 KVA and 800W1KVA at Cos.phi 0.8Static switchUSB and EPO emergency shutdown fittedAnomaly signal output board

GBP 2641.27

1

Gent 585051 Power Supply 2U - 24VDC 380A

Gent 585051 Power Supply 2U - 24VDC 380AThe Gent 585051 is an EN54-4 certified backup power supply unit. Designed with double conversion input and output voltage 230 V 50 Hz single-phase available power 1.6KW 2 KVA and 800W1KVA at Cos.phi. 0.8 static switch RS232 and USB and EPO emergency shutdown fitted as standard complete with anomaly signal output board.Key FeaturesEN54-4 CertifiedInput and output voltage 230 V 50 HzPower 1.6KW 2 KVA and 800W1KVA at Cos.phi 0.8Static switchUSB and EPO emergency shutdown fittedAnomaly signal output board

GBP 4418.83

1

Gent S4-34741-01 34740 Angle Bracket and Base

Gent S4-34741-01 34740 Angle Bracket and Base The Gent S4-34741-01 Beam Detector Angle Bracket Base is designed for use in areas where the S4-34740 beam detector will not be installed to a vertical surface or where the beam path is not perpendicular to the installation surface. It is supplied with a pre-installed S-Quad base.Gents S-Quad Beam Sensors provides an enhanced solution for linear beam detection for applications where point detection is either not practical or economic.Powered and controlled via the loop the beam is a market leading device with features such as one man alignment and commissioning which is achieved using the auto gain setting this ensure the optimum alignment is reached.Maintenance of the beam is enhanced with a key operated test feature which simulates the obscuration of the beam in a fire. The Gent loop powered beam is certified to EN54 parts 12 and 17.Key FeaturesAngle Bracket for difficult applications allowing wide angle adjustment up to - 30Multi angle fittingSupplied with baseSimple alignment

GBP 180.05

1

Gent S4-34805 Vigilon Manual Call Point with Resettable Element

Gent S4-34805 Vigilon Manual Call Point with Resettable ElementEvery manual call point is continuously monitored ensuring a trigger is responded to in less than one second system wide.The range includes options for glass and resettable elements and lift-up protective covers.A key switch version is also available for areas where tampering or vandalism is expected.An Environmentally Protected EP version with Ingress protection rating IP67 is also available complete with resettable element protective cover and backbox.Manual call points for the Vigilon and Nano system are easy to install and can be mounted on standard installation back boxes or bespoke red back boxes for surface mounting.Key FeaturesResettable or break glassLift up protective coversUp to 200 per loopIntegral short-circuit isolator

GBP 67.09

1

Gent S4-34800 Vigilon Manual Call Point with Glass Element IP43 Excludes Back Box

Gent S4-34800 Vigilon Manual Call Point with Glass Element IP43 Excludes Back BoxEvery manual call point is continuously monitored ensuring a trigger is responded to in less than one second system wide.The range includes options for glass and resettable elements and lift-up protective covers.A key switch version is also available for areas where tampering or vandalism is expected.An Environmentally Protected EP version with Ingress protection rating IP67 is also available complete with resettable element protective cover and backbox.Manual call points for the Vigilon and Nano system are easy to install and can be mounted on standard installation back boxes or bespoke red back boxes for surface mounting.Key FeaturesResettable or break glassLift up protective coversUp to 200 per loopIntegral short-circuit isolator

GBP 102.77

1

Gent S4-34842 Vigilon Manual Call Point with Glass Element and Protective Cover Excludes Back Box

Gent S4-34842 Vigilon Manual Call Point with Glass Element and Protective Cover Excludes Back BoxEvery manual call point is continuously monitored ensuring a trigger is responded to in less than one second system wide.The range includes options for glass and resettable elements and lift-up protective covers.A key switch version is also available for areas where tampering or vandalism is expected. An Environmentally Protected EP version with Ingress protection rating IP67 is also available complete with resettable element protective cover and backbox.Manual call points for the Vigilon and Nano system are easy to install and can be mounted on standard installation back boxes or bespoke red back boxes for surface mounting.Key FeaturesResettable or break glassLift up protective coversUp to 200 per loopIntegral short-circuit isolatorNo back box

GBP 103.61

1

Gent SAFE-RED-D-KIT SAFE 2 Button Red Plus Interface

Gent SAFE-RED-D-KIT SAFE 2 Button Red Plus InterfaceSAFE is a fully engineered solution for your building to allow you to bridge the gap between BS5839 Part 1 and BS5839 Part 6 without the risk of generating multiple false evacuations.Using our industry leading S-Quads and through the power of voice it enables clear alert and evacuation guidance to any building occupant.EN54 Part 2 Type B Dependency Approved.The SAFE buttons allows the occupants to control their local alarms in their alarm areas.The SAFE buttons allows the occupant to silence and test their local alarms. A confirmation LED is included to visually inform occupants that action has taken place.The button delays are fully configurable within the Vigilon Panel to cater for many applications where events can be managed by the user.In the landlords areas this will be designed to BS5839 Part 1 standards and in the residential areas to BS5839 Part 6 allowing you to manage your buildings installation to the appropriate standard.The SAFE 2 position switch kit containsSAFE Switch4 Channel InterfaceWiring loom Does not include interface enclosure

GBP 349.91

1

Gent SAFE-SS-D-KIT SAFE 2 Button Stainless Steel Plus Interface

Gent SAFE-SS-D-KIT SAFE 2 Button Stainless Steel Plus InterfaceSAFE is a fully engineered solution for your building to allow you to bridge the gap between BS5839 Part 1 and BS5839 Part 6 without the risk of generating multiple false evacuations.Using our industry leading S-Quads and through the power of voice it enables clear alert and evacuation guidance to any building occupant.EN54 Part 2 Type B Dependency Approved.The SAFE buttons allows the occupants to control their local alarms in their alarm areas.The SAFE buttons allows the occupant to silence and test their local alarms. A confirmation LED is included to visually inform occupants that action has taken place.The button delays are fully configurable within the Vigilon Panel to cater for many applications where events can be managed by the user.In the landlords areas this will be designed to BS5839 Part 1 standards and in the residential areas to BS5839 Part 6 allowing you to manage your buildings installation to the appropriate standard.The SAFE 2 position switch kit containsSAFE Switch4 Channel InterfaceWiring loom Does not include interface enclosure

GBP 300.65

1

Gent SAFE-WHITE-D-KIT SAFE 2 Button White Plus Interface

Gent SAFE-WHITE-D-KIT SAFE 2 Button White Plus InterfaceSAFE is a fully engineered solution for your building to allow you to bridge the gap between BS5839 Part 1 and BS5839 Part 6 without the risk of generating multiple false evacuations.Using our industry leading S-Quads and through the power of voice it enables clear alert and evacuation guidance to any building occupant.EN54 Part 2 Type B Dependency Approved.The SAFE buttons allows the occupants to control their local alarms in their alarm areas.The SAFE buttons allows the occupant to silence and test their local alarms. A confirmation LED is included to visually inform occupants that action has taken place.The button delays are fully configurable within the Vigilon Panel to cater for many applications where events can be managed by the user.In the landlords areas this will be designed to BS5839 Part 1 standards and in the residential areas to BS5839 Part 6 allowing you to manage your buildings installation to the appropriate standard.The SAFE 2 position switch kit containsSAFE Switch4 Channel InterfaceWiring loom Does not include interface enclosure

GBP 318.48

1

Gent SAFE-WHITE-S-KIT SAFE 1 Button White Plus Interface

Gent SAFE-WHITE-S-KIT SAFE 1 Button White Plus InterfaceSAFE is a fully engineered solution for your building to allow you to bridge the gap between BS5839 Part 1 and BS5839 Part 6 without the risk of generating multiple false evacuations.Using our industry leading S-Quads and through the power of voice it enables clear alert and evacuation guidance to any building occupant.EN54 Part 2 Type B Dependency Approved.The SAFE buttons allows the occupants to control their local alarms in their alarm areas.The SAFE buttons allows the occupant to silence and test their local alarms. A confirmation LED is included to visually inform occupants that action has taken place.The button delays are fully configurable within the Vigilon Panel to cater for many applications where events can be managed by the user.In the landlords areas this will be designed to BS5839 Part 1 standards and in the residential areas to BS5839 Part 6 allowing you to manage your buildings installation to the appropriate standard.The SAFE 1 position switch kit containsSAFE Switch4 Channel InterfaceWiring loom does not include interface enclosureKey FeaturesColour WhiteEN54 Part 2 Type B Dependency Approved

GBP 282.82

1

Gent S4-34741 Beam Sensor Transmitter

Gent S4-34741 Beam Sensor TransmitterThe S4-34741 from Gent is a Beam Sensor Emitter.Vigilons loop powered technology allows up to 16 beam pairs to be connected to the same loop circuit each covering a distance of up to 100m without the need for an external Power Supply Unit wiring or interfacing.Compatible with the full range of Vigilon and Nano control panels the S-Quad beam uses the panel software to ensure a fast response to fi re while offering software filters to reduce the number of unwanted alarms.What is a Beam SensorA beam sensor works when theemittersends out abeamof light most often a pulsed infrared visible red or laser that diffuses in all directions filling a detection area. The target then enters the area and deflects part of thebeamback to the receiver.If anything is detected it will signal an alarm.Key FeaturesEach beam can be set to one of 6 sensitivity states to provide a best fi t for individual applicationsThe beam provides increased resilience to interference from the sun and other light sourcesRemote key switch provides test facility at ground level without the need to gain access to beams mounted in high areasThe beam incorporates an LED array to indicate signal strength allowing accurate alignment during one person commissioningOptimum sensitivity is maintained by automatic gain setting triggered at the beam during alignmentThe optical lens design is intended to minimise build up of dust to reduce the maintenance and cleaning requiredThe S-Quad beam is compatible with early versions of the Vigilon Beam using the S-Quad programming base avoiding the need to upgrade to latest control software