4 results (0,12885 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Hochiki CHQ-DIM2MSCI Marine Dual Input Module with SCI

Hochiki CHQ-DIM2MSCI Marine Dual Input Module with SCI

Hochiki CHQ-DIM2MSCI Marine Dual Input Module with SCIModel CHQ-DIM2MSCI is a Marine Approved Dual Input Module designed to interface to a variety of inputs such as door contacts sprinkler flowdoor switches and plant equipment. Also features an integral short-circuit isolator.A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-DIM2MSCI increases the IP rating to IP65.Key FeaturesSingle Loop AddressLoop Powered2 Independent Inputs for Monitoring of Volt Free ContactsEach Input can be Configured to Monitor either Normally Open or Normally Closed contactsSmart-Fix Housing System for flexibilityFeatures an integral SCIApproved to MED by GLGL Type ApprovalApproved by LPCB

GBP 62.12
1

Hochiki Marine Single Zone Monitor with SCI CHQ-SZM2MSCI

Hochiki Marine Single Zone Monitor with SCI CHQ-SZM2MSCI

Hochiki CHQ-SZM2MSCI Marine Single Zone Monitor with SCIThe CHQ-SZM2MSCI is a Marine Approved Single Zone Monitor designed to allow up to 6 marine approved conventional detectors to be interfaced to Hochikis ESP analogue addressable system. The unit also features an integral short-circuit isolator.The CHQ-SZM2MSCI utilises simple DIL switches for reliable addressing. A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-SZM2MSCI increases the IP rating to IP65.Key FeaturesLoop Powered with Single Loop AddressUp to 6 Conventional DetectorsRemote LED OutputFully Monitored for Short and Open Circuit FaultsSmart-Fix Housing System for flexibilityFeatures an integral SCIApproved to MED by GLGL Type approvalApproved by LPCBPlease Note The conventional zone on the CHQ-SZM2MSCI does not support any line continuity options if Call Points are being interfaced they should be wired at the beginning of the zone.

GBP 68.87
1

Hochiki CHQ-DRC2MSCI Marine Approved Dual Relay Controller With SCI

Hochiki CHQ-DRC2MSCI Marine Approved Dual Relay Controller With SCI

Hochiki CHQ-DRC2MSCI Marine Approved Dual Relay Controller With SCIThe CHQ-DRC2MSCI is a Marine Approved Dual Relay Controller module designed to provide two general-purpose relay outputs each output can be driven separately for control of such devices as dampers or for control of plant and equipment shutdown. The monitored input can be used for local power supply fault monitoring or as a general-purpose input.The unit also features an integral short-circuit isolator. The CHQ-DRC2MSCI utilises simple DIL switches for reliable addressing. A back box is also available CHQ-BACKBOX which when used in conjunction with the CHQ-DRC2MSCI increases the IP rating to IP65.Key FeaturesApproved to MED by DNVLoop powered with single loop addressProvides 2 Independently controlled changeover relaysRelays contact rated at 30 VDC at 1 AAuxiliary monitored inputFeatures an integral SCICan be used with CHQ-BACKBOX to comply with BS 7671SIL2 and Railway Approved variants available

GBP 83.29
1

Hochiki Addressable Marine Call Point with SCI HCP-EMSCI

Hochiki Addressable Marine Call Point with SCI HCP-EMSCI

Hochiki HCP-EMSCI Addressable Marine Call Point with SCIThe HCP-EMSCI is a Manual Call Point with integral short-circuit isolator which is fully compatible with Hochikis ESP analogue addressable protocol. The unit incorporates a bi-coloured LED which can be selected as pulsingnon-pulsing1 for communications polling and is continuously lit when the unit is operated in these two states the LED will show red. The LED will show amber when a short-circuit is present but will switch to red if the unit is activated.The unit operates by pressing the EN54 compliant non-frangible plastic element and produces a high-level ESP interrupt. A built-in test function initiated by the control panel ensures the integrity of the device at all times and the device can be tested by insertion of a test key in the underside of the unit. Two terminal blocks are provided for easy connection to the loop wiring.The unit is addressed using the TCH-B200 Hand Held Programmer for quick and reliable addressing. The unit can be flush mounted as supplied. For surface fixing a suitable back box such as the SR MOUNTING BOX is required sold separately. An optional glass element is also available.Key FeaturesApproved to MED by GLSIL Level 2 approved variant availableIdeal for use in oil and gas environmentsFast responseIntegral short-circuit isolatorBi-coloured status LEDNon-frangible element fitted as standard conforms to EN54Addressed with TCH-B200 Hand Held ProgrammerSurface or flush mounting if surface mounting requires SR MOUNTING BOX sold separatelyLPCB Approved to EN54

GBP 44.60
1