feed zone portables from GBP 70 | See the cheapest prices and offers on css.lazzaweb.dk

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 15m

Huntingdon Fusion Technique's (HFT) off-the-shelf Argon Feed Hose is available in a variety of standard lengths, including 30m, 25m, 20m, 15m, 10m, and 5m. Each assembly is crafted to meet high-quality standards and comes equipped with an argon regulator fitting on one end and a 12 mm to 12 mm quick connect fitting on the other end. We also offer a range of alternative fittings, such as hose tails, tailpieces, and various quick disconnect options. What's In The Box APBS409 - Coupling, Female Thread 3/8" BSP (to fit cylinder regulator) APBS412 - Hose Tail 6.35 mm (1/4") ID to suit APBS409 APBS411 - Male threaded tailpiece 1/4" to suit APGV5002 Order APGV5002 to fit to PurgElite, PurgExtra, QuickPurge and HotPurge Inflatable Tube, Pipe and Pipeline Weld Purging Systems. FAQs 1. Do I have to attach the fittings to the hose myself? No, the hose comes complete with the fittings crimped onto each end. 2. I require a length of hose not shown on the price list, is this possible? Yes, contact us with your desired length and we will quote a price. 3. Is there a maximum length? Yes, 100m is the longest length in a straight run; however, longer lengths can be made up with joining connectors. 4. Is the hose stamped with the specification? Yes, each length of hose is marked in white ink along the length with the specification: Argon Gas Hose BS EN 559 20 Bar (300 PSI) WP-MM.ID. 5. Do you keep good stocks? Yes, we have hose and all fittings in stock, and lengths can be made up quickly by our assembly team. 6. Can I purchase the fittings separately if required? Yes, all fittings can be bought individually. 7. Does the hose have a British Standard? Yes, it is BS EN 559. 8. What is the temperature resistance range of the hose? From -30C up to +80C. 9. Is the hose just for argon? No, it can also be used for nitrogen. 10. How much does it weigh? 0.16 kg per metre. 11. What are the dimensions of the hose? The ID is 6 mm and the OD is 13 mm. 12. What is the maximum pressure rating of the hose? Working pressure is 300 psi, 20 bar.

GBP 109.99

1

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 25m

Huntingdon Fusion Technique's (HFT) off-the-shelf Argon Feed Hose is available in a variety of standard lengths, including 30m, 25m, 20m, 15m, 10m, and 5m. Each assembly is crafted to meet high-quality standards and comes equipped with an argon regulator fitting on one end and a 12 mm to 12 mm quick connect fitting on the other end. We also offer a range of alternative fittings, such as hose tails, tailpieces, and various quick disconnect options. What's In The Box APBS409 - Coupling, Female Thread 3/8" BSP (to fit cylinder regulator) APBS412 - Hose Tail 6.35 mm (1/4") ID to suit APBS409 APBS411 - Male threaded tailpiece 1/4" to suit APGV5002 Order APGV5002 to fit to PurgElite, PurgExtra, QuickPurge and HotPurge Inflatable Tube, Pipe and Pipeline Weld Purging Systems. FAQs 1. Do I have to attach the fittings to the hose myself? No, the hose comes complete with the fittings crimped onto each end. 2. I require a length of hose not shown on the price list, is this possible? Yes, contact us with your desired length and they will quote a price. 3. Is there a maximum length? Yes, 100m is the longest length in a straight run, however longer lengths can be made up with joining connectors. 4. Is the hose stamped with the specification? Yes, each length of hose is marked in white ink along the length with the specification: Argon Gas Hose BS EN 559 20 Bar (300 PSI) WP-MM.ID. 5. Do you keep good stocks? Yes, we have hose and all fittings in stock and lengths can be made up quickly by our assembly team. 6. Can I purchase the fittings separately if required? Yes, all fittings can be bought individually. 7. Does the hose have a British Standard? Yes, it is BS EN 559. 8. What is the temperature resistance range of the hose? From -30C up to +80C. 9. Is the hose just for argon? No, it can also be used for nitrogen. 10. How much does it weigh? 0.16 kgs per metre. 11. What are the dimensions of the hose? The ID is 6 mm and the OD is 13 mm. 12. What is the maximum pressure rating of the hose? Working pressure is 300 psi, 20 bar.

GBP 149.99

1

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 30m

Huntingdon Fusion Technique's (HFT) off-the-shelf Argon Feed Hose is available in a variety of standard lengths, including 30m, 25m, 20m, 15m, 10m, and 5m. Each assembly is crafted to meet high-quality standards and comes equipped with an argon regulator fitting on one end and a 12 mm to 12 mm quick connect fitting on the other end. We also offer a range of alternative fittings, such as hose tails, tailpieces, and various quick disconnect options. What's In The Box APBS409 - Coupling, Female Thread 3/8" BSP (to fit cylinder regulator) APBS412 - Hose Tail 6.35 mm (1/4") ID to suit APBS409 APBS411 - Male threaded tailpiece 1/4" to suit APGV5002 Order APGV5002 to fit to PurgElite, PurgExtra, QuickPurge and HotPurge Inflatable Tube, Pipe and Pipeline Weld Purging Systems. FAQs 1. Do I have to attach the fittings to the hose myself? No, the hose comes complete with the fittings crimped onto each end. 2. I require a length of hose not shown on the price list, is this possible? Yes, contact us with your desired length and they will quote a price. 3. Is there a maximum length? Yes, 100m is the longest length in a straight run, however longer lengths can be made up with joining connectors. 4. Is the hose stamped with the specification? Yes, each length of hose is marked in white ink along the length with the specification: Argon Gas Hose BS EN 559 20 Bar (300 PSI) WP-MM.ID. 5. Do you keep good stocks? Yes, we have hose and all fittings in stock and lengths can be made up quickly by our assembly team. 6. Can I purchase the fittings separately if required? Yes, all fittings can be bought individually. 7. Does the hose have a British Standard? Yes, it is BS EN 559. 8. What is the temperature resistance range of the hose? From -30C up to +80C. 9. Is the hose just for argon? No, it can also be used for nitrogen. 10. How much does it weigh? 0.16 kgs per metre. 11. What are the dimensions of the hose? The ID is 6 mm and the OD is 13 mm. 12. What is the maximum pressure rating of the hose? Working pressure is 300 psi, 20 bar.

GBP 169.99

1

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 20m

Huntingdon Fusion Technique's (HFT) off-the-shelf Argon Feed Hose is available in a variety of standard lengths, including 30m, 25m, 20m, 15m, 10m, and 5m. Each assembly is crafted to meet high-quality standards and comes equipped with an argon regulator fitting on one end and a 12 mm to 12 mm quick connect fitting on the other end. We also offer a range of alternative fittings, such as hose tails, tailpieces, and various quick disconnect options. What's In The Box APBS409 - Coupling, Female Thread 3/8" BSP (to fit cylinder regulator) APBS412 - Hose Tail 6.35 mm (1/4") ID to suit APBS409 APBS411 - Male threaded tailpiece 1/4" to suit APGV5002 Order APGV5002 to fit to PurgElite, PurgExtra, QuickPurge and HotPurge Inflatable Tube, Pipe and Pipeline Weld Purging Systems. FAQs 1. Do I have to attach the fittings to the hose myself? No, the hose comes complete with the fittings crimped onto each end. 2. I require a length of hose not shown on the price list, is this possible? Yes, contact us with your desired length and they will quote a price. 3. Is there a maximum length? Yes, 100m is the longest length in a straight run, however longer lengths can be made up with joining connectors. 4. Is the hose stamped with the specification? Yes, each length of hose is marked in white ink along the length with the specification: Argon Gas Hose BS EN 559 20 Bar (300 PSI) WP-MM.ID. 5. Do you keep good stocks? Yes, we have hose and all fittings in stock and lengths can be made up quickly by our assembly team. 6. Can I purchase the fittings separately if required? Yes, all fittings can be bought individually. 7. Does the hose have a British Standard? Yes, it is BS EN 559. 8. What is the temperature resistance range of the hose? From -30C up to +80C. 9. Is the hose just for argon? No, it can also be used for nitrogen. 10. How much does it weigh? 0.16 kg per metre. 11. What are the dimensions of the hose? The ID is 6 mm and the OD is 13 mm. 12. What is the maximum pressure rating of the hose? Working pressure is 300 psi, 20 bar.

GBP 129.99

1

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 10m

Huntingdon Fusion Technique's (HFT) off-the-shelf Argon Feed Hose is available in a variety of standard lengths, including 30m, 25m, 20m, 15m, 10m, and 5m. Each assembly is crafted to meet high-quality standards and comes equipped with an argon regulator fitting on one end and a 12 mm to 12 mm quick connect fitting on the other end. We also offer a range of alternative fittings, such as hose tails, tailpieces, and various quick disconnect options. What's In The Box APBS409 - Coupling, Female Thread 3/8" BSP (to fit cylinder regulator) APBS412 - Hose Tail 6.35 mm (1/4") ID to suit APBS409 APBS411 - Male threaded tailpiece 1/4" to suit APGV5002 Order APGV5002 to fit to PurgElite, PurgExtra, QuickPurge and HotPurge Inflatable Tube, Pipe and Pipeline Weld Purging Systems. FAQs 1. Do I have to attach the fittings to the hose myself? No, the hose comes complete with the fittings crimped onto each end. 2. I require a length of hose not shown on the price list, is this possible? Yes, contact us with your desired length and we will quote a price. 3. Is there a maximum length? Yes, 100m is the longest length in a straight run; however, longer lengths can be made up with joining connectors. 4. Is the hose stamped with the specification? Yes, each length of hose is marked in white ink along the length with the specification: Argon Gas Hose BS EN 559 20 Bar (300 PSI) WP-MM.ID. 5. Do you keep good stocks? Yes, we have hose and all fittings in stock, and lengths can be made up quickly by our assembly team. 6. Can I purchase the fittings separately if required? Yes, all fittings can be bought individually. 7. Does the hose have a British Standard? Yes, it is BS EN 559. 8. What is the temperature resistance range of the hose? From -30C up to +80C. 9. Is the hose just for argon? No, it can also be used for nitrogen. 10. How much does it weigh? 0.16 kgs per metre. 11. What are the dimensions of the hose? The ID is 6 mm and the OD is 13 mm. 12. What is the maximum pressure rating of the hose? Working pressure is 300 psi, 20 bar.

GBP 89.99

1

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 5m

Huntingdon Fusion Technique's (HFT) off-the-shelf Argon Feed Hose is available in a variety of standard lengths, including 30m, 25m, 20m, 15m, 10m, and 5m. Each assembly is crafted to meet high-quality standards and comes equipped with an argon regulator fitting on one end and a 12 mm to 12 mm quick connect fitting on the other end. We also offer a range of alternative fittings, such as hose tails, tailpieces, and various quick disconnect options. What's In The Box APBS409 - Coupling, Female Thread 3/8" BSP (to fit cylinder regulator) APBS412 - Hose Tail 6.35 mm (1/4") ID to suit APBS409 APBS411 - Male threaded tailpiece 1/4" to suit APGV5002 Order APGV5002 to fit to PurgElite, PurgExtra, QuickPurge and HotPurge Inflatable Tube, Pipe and Pipeline Weld Purging Systems. FAQs 1. Do I have to attach the fittings to the hose myself? No, the hose comes complete with the fittings crimped onto each end. 2. I require a length of hose not shown on the price list, is this possible? Yes, contact us with your desired length and they will quote a price. 3. Is there a maximum length? Yes, 100m is the longest length in a straight run, however longer lengths can be made up with joining connectors. 4. Is the hose stamped with the specification? Yes, each length of hose is marked in white ink along the length with the specification: Argon Gas Hose BS EN 559 20 Bar (300 PSI) WP-MM.ID. 5. Do you keep good stocks? Yes, we have hose and all fittings in stock and lengths can be made up quickly by our assembly team. 6. Can I purchase the fittings separately if required? Yes, all fittings can be bought individually. 7. Does the hose have a British Standard? Yes, it is BS EN 559. 8. What is the temperature resistance range of the hose? From -30C up to +80C. 9. Is the hose just for argon? No, it can also be used for nitrogen. 10. How much does it weigh? 0.16 kgs per metre. 11. What are the dimensions of the hose? The ID is 6 mm and the OD is 13 mm. 12. What is the maximum pressure rating of the hose? Working pressure is 300 psi, 20 bar.

GBP 69.99

1

Huntingdon Fusion Techniques Purgenet Dew Point Purging Gas Moisture Sensor DPS1000

The HFT PurgeNet Dew Point Purging Gas Moisture Sensor revolutionises the measurement of the dew point for critical welds, making it incredibly easy. With its seamless integration capability into any of Huntingdon Fusion's high spec PurgEye Weld Purge Monitors, the HFT PurgeNet Dew Point Purging Gas Moisture Sensor eliminates the need for Companies involved in critical joint welding to invest in a separate and costly Dew Point Meter, offering accurate readings down to 1 ppm (with a precision of 10 ppm) . Dew Point Purging Gas Moisture Sensor is suitable for the following types of gases: Argon (Ar) Oxygen (O2) Nitrogen (N2) Hydrogen (H2) Carbon Dioxide (CO2) Features Integration Compatibility: It is designed to seamlessly integrate with high spec PurgEye Weld Purge Monitors, providing a comprehensive solution for measuring both dew point and weld purge parameters. Dew Point Measurement: The sensor is specifically designed for accurate measurement of the dew point, enabling precise assessment of moisture levels in the purging gas during critical welds. Wide Reading Range: It can measure dew points down to 1 ppm, ensuring high sensitivity and enabling precise control of moisture levels. The accuracy of the measurements is rated at 10 ppm. Cost Savings: By eliminating the need to purchase a separate and expensive dew point meter, the HFT PurgeNet Dew Point Purging Gas Moisture Sensor helps companies reduce costs and streamline their welding processes. User-Friendly: The sensor is designed to be user-friendly and easy to operate, simplifying the measurement process for welders and technicians. Reliability: It is built to deliver reliable and consistent results, ensuring that critical welds are performed under optimal conditions with controlled moisture levels. Durability: The sensor is constructed with durable materials to withstand the harsh environments typically encountered during welding operations, ensuring its longevity and performance. Compatibility PurgEye 200 PurgEye 500 Desk PurgEye 600 PurgEye 1000 Remote PurgEye 1500 Site FAQs 1. What is Dew? Dew is expressed as drops of liquid water that condense from the atmosphere and onto any solid surface like metal. 2. What is the Dew Point? The dew point is the temperature in C or F at which air is saturated with water vapour (also referred to as humidity) Below the dew point, water will begin to condense on solid surfaces in the welding environment. 3. How does water moisture affect the quality of the weld joint? Under arc conditions, water is broken down into hydrogen and oxygen in atomic form which, when present in weld metal, cause porosity and are known to create cracking in the weld joint. 4. Why should I use a Dew Point Purging Gas Moisture Sensor? Using the PurgeNet Dew Point Purging Gas Moisture Sensor while welding is the easiest method for indicating when water will condense on solid surfaces in the welding zone. Water can form as moisture on metal surfaces while welding and it is important to be able to measure Dew Point while welding lengthy critical joints as conditions can change during the welding process. 5. How does the Dew Point Purging Gas Moisture Sensor give readings? The PurgEye Dew Point Sensor accessory has been designed to integrate with most of the Argweld Weld Purge Monitors via the PurgeNet lead that is supplied with them, thereby giving values and water present on the same screen. In this way, the user is not forced into the purchase of an expensive, separate Dew Point Monitor that will give its reading elsewhere. 6. Which Weld Purge Monitors are compatible with the Dew Point Purging Gas Moisture Sensor? The PurgeNet Dew Point Purging Gas Moisture Sensor is compatible with the PurgEye 200, 500 Desk, 600, 1000 Remote and 1500 Site.

GBP 4099.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 914mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1399.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 711mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1139.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1092mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1599.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1422mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1999.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 787mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1199.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1448mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1999.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 584mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1039.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1194mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1699.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 152mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 469.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 330mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 599.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 737mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1199.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 483mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 799.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1346mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1999.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1219mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1699.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 254mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 569.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 762mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 1199.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 406mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 699.99

1

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 381mm

The Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge System comprises a tandem inflatable dam system connected by a volume reducing sleeve. Operating temperature 250C (482F) continuous use and up to 280C (586F) for short periods. The size of the system to be ordered must correspond with the ID of the pipe being welded. All systems come fitted with PurgeGate as standard.The QuickPurge design works best by keeping the sleeve as short as possible to fast results. With the short sleeve, it is difficult to pull the system through 90 bends. In the event that you will need to pull your QuickPurge system through 90 bends, please contact us.BenefitsTandem inflatable dam system: This ensures a complete seal around the weld joint, preventing oxygen from entering and causing oxidation.Volume reducing sleeve: This reduces the volume of the annulus between the pipes, which speeds up the purge process.Operating temperature of up to 250C (482F) continuously and up to 280C (586F) for short periods: This makes it suitable for a wide range of applications.Comes with PurgeGate as standard: This prevents the dams from overinflating and bursting, which can damage the system.Easy to use: The system is designed to be quick and easy to set up, even for inexperienced users.Fast results: The system can purge a pipe in minutes, which can save time and money.Can be used in pipes with a maximum bend radius of 1.5 times the pipe diameter: This makes it suitable for a wide range of pipes, including pipes with bends.FAQs1. How can Argweld QuickPurge help me?Dramatically reduced welding times achieved. Phenomenal savings in argon. For example, a 36 (900 mm) pipe joint might take from 4 to 8 hours to prepare and purge properly when using homemade devices such as discs made from cardboard, foam or rubber.With Argweld QuickPurge, it takes as little as 10 minutes which includes placing the system into position, inflating the dams and purging.2. What range of sizes is available?6 to 88 (152 to 2, 235 mm) 3. What is the overall length?Lengths will vary according to the diameter. The space between the dams is kept very short to minimise inert gas use consistent with the need to provide adequate gas coverage.4. Can Argweld QuickPurge Systems be used for return bends?It is necessary to tell HFT at the time of order, that the QuickPurge System is required for return bends. We will then manufacture longer collars to provide the necessary space to prevent the dams from being too close to the weld.5. Are Argweld QuickPurge Systems re-usable?Yes, QuickPurge II pays for itself in a few welds. QuickPurge is rugged and can be used for multiple welds.6. What gases can I use with Argweld QuickPurge Systems?Argon (Europe) and helium (N America) are the most common gases but any gas or gas mix can be used. Argon/hydrogen mixes and nitrogen have been used successfully.7. What are Argweld QuickPurge Systems made from?Predominantly low vapour pressure, flexible, durable, heat resistant materials selected for longevity.8. How cost-effective are Argweld QuickPurge Systems?Ask for our return on investment sheet. The savings using QuickPurge are really stunning.9. Are Argweld QuickPurge Systems resistant to heat?Yes, QuickPurge is resistant to the heat of all typical arc welding processes.Special heat-protected purge systems called Argweld HotPurge are available to accommodate pre-weld and post-weld heat treated joints.Heat Protecting Band accessories are available for Keyhole Tig or Keyhole Plasma welding. Or for any other applications where the material under the weld becomes too hot.10. How do I measure the residual oxygen content?Use a dedicated PurgEye Weld Purge Monitor.11. How do I position the product in the pipeline?QuickPurge Systems are manufactured with high strength pull loops that allow the fixing of pull cords. RootGlo is a glow sleeve which can be seen readily through the root gap when making open root welds. Exposure to 10 minutes of light provides illumination inside the pipe for up to 12 hours.12. How long will Argweld QuickPurge Systems remain inflated?Continuous purging will ensure effective sealing and this allows time for post-weld cooling and x-ray or ultrasonic inspection. Deflation is instant once the argon feed hose has been disconnected.

GBP 649.99

1

Awardvindende Google Marketing Powerhouse

Brand

Size

Merchant

Price (EUR)

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 15m

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 25m

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 30m

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 20m

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 10m

Huntingdon Fusion Techniques Argweld Argon Gas Feed Hose Assembly - 5m

Huntingdon Fusion Techniques Purgenet Dew Point Purging Gas Moisture Sensor DPS1000

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 914mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 711mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1092mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1422mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 787mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1448mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 584mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1194mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 152mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 330mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 737mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 483mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1346mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 1219mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 254mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 762mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 406mm

Huntingdon Fusion Techniques Argweld QuickPurge Tube, Pipe & Pipeline Inflatable Weld Purge Systems - 381mm

Powered by Cobiro