11 results (0,12974 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Kentec DNX-A-2R-K RS485 Dynamic Network Analyser

Kentec DNX-A-2R-K RS485 Dynamic Network Analyser

Kentec DNX-A-2R-K RS485 Dynamic Network AnalyserThe DNX-A-2R-K is an RS485 Dynamic Network Analyser for Ring Topology Networks. This product has been developed to facilitate dynamic network management through the provision of an independent communication layer.The equipment is designed to improve the Quality of Service QoS of critical communication networks while operating under the performance criteria required by EN54-13 and BS5839 part 1.The ports connected to the communications ring are correctly terminated to match the network communications cable impedance to ensure optimum signal quality and amplitude.Signal quality is constantly monitored and the termination impedance is adjusted to compensate for changes in cable impedance due to climatic or physical cable parameter changes.Four InputOutput interfaces are provided for through an independent communications layer. This feature provides a basic redundant network protocol with the mapping configuration managed through the PC graphics IVIEW programming tool.An upgrade license DNX-R-2R-K-UG is available for this module which enables compatibility with IVIEW graphical software for network analysis support.Key FeaturesIndependent reporting with Class A communication redundancy with multiple fault tolerance2.5 kV galvanic isolation on all portsDual and single industrial equipment RS485 connection4 independent IO channels across the redundant network ring for independent protocol redundancyCan operate on Hosted Fibre Ethernet linksSimple LED system status indicationSignal quality and amplitude visual indicationWireless connectivity for remote monitoring using a Bluetooth or WiFi interfaceSupports the generation of system performance reports for Installation commissioningVisual interface provide by IVIEW the graphical user interface with monitoring diagnostics and reporting optionsEnables preventative maintenance management through system degradation monitoringConfiguration and commissioning parameters are stored allowing for system performance tracking over timeBaud rate selectable from 9600-115200 bitssecDIN rail mounting

GBP 1591.74
1

Kentec DNP-R-2FFC-K Passive RS485Fibre amp Dual Fibre Dynamic Network Analyser

Kentec DNP-R-2FFC-K Passive RS485Fibre amp Dual Fibre Dynamic Network Analyser

Kentec DNP-R-2FFC-K Passive RS485Fibre Dual Fibre Dynamic Network AnalyserThe DNP-R-2FFC-K is a full fibre or hybrid copperfibre modem developed for use with fire panels in the life safety industry. The equipment is designed to improve the Quality of Service QoS of critical communication networks while operating under the performance criteria required by EN54-13 and BS5839 part 1.DNP-R-2FFC-K is designed to support dual fibre connectivity Fibre in Fibre out using the range of INS Small Form-factor Pluggable fibre optic transceivers. INS transceivers are available to support single-mode multimode and Bi-Directional fibre optic cables with distances of up to 160km.DNP-R-2FFC-K is also designed to support fibre optic to RS485 copper wiring which allows sections of an RS485 network to be converted to fibre optic cables either for enhanced transmission distances or to overcome problems with EMI Electro-Magnetic Interference.Configuring the module for fibre or RS485 fibre configurations is done through a single switch option. Simple LED indications provide detailed information regarding the communication status of each port signal quality transceiver status etc.Key FeaturesSupport Full Fibre or RS485Fibre configurationsOnly one module required per panelSimple LED status indications provide detailed diagnostic infoSupports INS Small Form-factor Pluggable SFP Fibre Optic transceiversRedundant power supply connections for increased reliabilityBaud rate selectable 9600 - 115200 bitssecDIN rail mountingSupport of single and dual port industrial equipment

GBP 1399.07
1

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550

Kentec INST-SFP-BiDi-10K-BA-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1310nm TX1550INST-SFP-BiBi-10K-AB-1INST-SFP-BiBi-10K-BA-1 are fibre optic transceivers for use with multi mode fibre optic cable and operate at a nominal wavelength of 850nm.This dongle is locked and preconfigured for use with Kentec DNP-R-2FFC-K Passive Dual Port Optic FibreRS485 Medium Converter.Transceivers are hot-pluggable making them quick easy to replace and also swap between alternate fibre optic modes. Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km.The transmitter section uses a Vertical Cavity Surface Emitted Laser and is Class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated Gas detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. AB-1BA-1 are designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNP-R-2FFC-K converter module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesOperating data rates up to 1.25Gbps10km reach for 9125m Single Mode FibreSingle 3.3V power supply and TTL Logic InterfaceLow power dissipationHot-pluggable SFP footprintBIDI LCUPC type pluggable optical interfaceClass 1 FDA and IEC60825-1 laser safety compliantBuilt in digital diagnostic functions including optical power monitoringRoHS compliant and lead-freeCompliant with SFP MSACompliant with SFF-8472Compliant with IEEE 802.3z

GBP 149.22
1

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310

Kentec INST-SFP-BiDi-10K-AB-1 SFP Bi-directional Single Mode Fibre Optic Transceiver 1550nm TX1310INST-SFP-BiBi-10K-AB-1INST-SFP-BiBi-10K-BA-1 are fibre optic transceivers for use with multi mode fibre optic cable and operate at a nominal wavelength of 850nm.This dongle is locked and preconfigured for use with Kentec DNP-R-2FFC-K Passive Dual Port Optic FibreRS485 Medium Converter.Transceivers are hot-pluggable making them quick easy to replace and also swap between alternate fibre optic modes. Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km.The transmitter section uses a Vertical Cavity Surface Emitted Laser and is Class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated Gas detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. AB-1BA-1 are designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNP-R-2FFC-K converter module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesOperating data rates up to 1.25Gbps10km reach for 9125m Single Mode FibreSingle 3.3V power supply and TTL Logic InterfaceLow power dissipationHot-pluggable SFP footprintBIDI LCUPC type pluggable optical interfaceClass 1 FDA and IEC60825-1 laser safety compliantBuilt in digital diagnostic functions including optical power monitoringRoHS compliant and lead-freeCompliant with SFP MSACompliant with SFF-8472Compliant with IEEE 802.3z

GBP 149.22
1

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550m

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550m

Kentec INST-SFP-MM-01-K SFP Multi-Mode Fibre Optic Transceiver 550mINST-SFP-MM-01-K is a fibre optic transceiver for use with multimode fibre optic cable and operates at a nominal wavelength of 850nm.This dongle is locked and pre-configured for use with the Kentec DNX-R-2FFC-K RS485Fibre Dual Fibre Dynamic Network Analyser.INST-SFP-MM-01-K transceivers are hot-pluggable making it quick easy to replace and also swap between alternate fibre optic modes.Maximum range will be dependent upon the fibre optic cable used 62.5125m range of 550m 50125m can extend the range up to 1km. The transmitter section uses a Vertical Cavity Surface Emitted Laser and is class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated GaAs detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. INST-SFP-MM-01-K is designed to be compliant with SFF-8472 MSA.Built in digital diagnostic functions allow monitoring of the transceiver by the DNX-R-2FFC-K analyser module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesPlug-in transceiver for use with DNX-R-2FFC-K analysers provides a multi-mode fibre communication link between transceivers on the networkMax distance between analysers 550mOperating data rates up to 1.25GbpsSingle 3.3V power supply and TTL Logic InterfaceHot-pluggable SFP footprint duplex LC connector interface.Class 1 FDA and IEC60825-1 laser safety compliant.Commercial temperature range -4085oCCompliant with SFF-8472 MSABuilt-in digital diagnostic functions including optical power monitoring

GBP 131.75
1

Kentec INST-SFP-SS-20K-1 SFP Single Mode Fibre Optic Transceiver 20Km

Kentec INST-SFP-SS-20K-1 SFP Single Mode Fibre Optic Transceiver 20Km

Kentec INST-SFP-SS-20K-1 SFP Single Mode Fibre Optic Transceiver 20KmINST-SFP-SS-20K-1 is a fibre optic transceiver for use with single mode fibre optic cable and operates at a nominal wavelength of 1310nm. This dongle is locked and pre-configured for use with the DNX-R-2FFC-K RS485Fibre Dual Fibre Dynamic Network Analyser.INST-SFP-SS-20K-1 transceivers are hot-pluggable making it quick easy to replace and also swap between alternate fibre optic modes. Maximum range is 20Km based upon a 9125m fibre optic cable.The transmitter section uses a multiple quantum well 1310nm laser and is class 1 laser compliant according to International Safety Standard IEC60825.The receiver section uses an Integrated GaAs detector pre-amplifier IDP mounted in an optical header and a limiting post-amplifier IC. INST-SFP-SS-20K-1 is designed to be compliant with SFF-8472 MSA. Built in digital diagnostic functions allow monitoring of the transceiver by the DNX-R-2FFC-K analyser module and subsequently the IVIEW software tool. This allows performance monitoring along with early warning of a potential issue to enable preventative maintenance.Key FeaturesPlug-in transceiver for use with DNX-R-2FFC-K analysers provides a single mode fibre communication link between transceivers on the networkMax distance between analysers 20kmOperating data rates up to 1.25Gbps1310nm FP laser transmitter20km reach for 9125m fibre optic cableSingle 3.3V power supply and TTL Logic InterfaceHot-pluggable SFP footprint duplex LC connector interfaceClass 1 FDA and IEC60825-1 laser safety compliantCommercial temperature range 070CCompliant with SFF-8472 MSABuilt-in digital diagnostic functions including optical power monitoring

GBP 131.75
1

Kentec K1810-13 Sigma A-XT Extinguishant Control Panel - 230V Red

Kentec K1810-13 Sigma A-XT Extinguishant Control Panel - 230V Red

Kentec K1810-13 Sigma A-XT Extinguishant Control Panel - 230V RedSigma A-XT releasing panel offers outstanding value and performance for all small to medium fixed fire-fighting installations.With three initiating circuits as standard release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three types of activations for detection in ceiling void room and floor void applications.The extensive configuration options of the Sigma A-XT allow the functionality of the system to be extensively modified. The panel contains a large LED display to enable easy configuration and control which also displays the time remaining until release for added user safety.The countdown time is duplicated on up to seven remote status units to provide local indication of the system status.With all the electronics mounted on a single easily removable steel plate Sigma A-XT panels are both robust and easy to install. Sigma A-XT is supplied in an enclosure that matches the design and colour of the Elite RS range and is available in standard red or optional grey.The K16400M2 from the extensive range of Kentec products is a syncro IO expansion card enclosure with 5.25A power supply. flexibility to create customised IO panel.Key FeaturesUL864 and FM ListedThree initiation circuits as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage NAC delaysConfigurable detection delaysZero time delay upon manual release optionSupports up to seven four wire status indicatorsBuilt in Extract Fan controlCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable releasing delays up to 60 seconds in 5 second stopsConfigurable releasing duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining until release

GBP 628.31
1

Kentec K1810-43 Sigma A-XT Extinguishant Control Panel - 230V Grey

Kentec K1810-43 Sigma A-XT Extinguishant Control Panel - 230V Grey

Kentec K1810-43 Sigma A-XT Extinguishant Control Panel - 230V GreySigma A-XT releasing panel offers outstanding value and performance for all small to medium fixed fire-fighting installations.With three initiating circuits as standard release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three types of activations for detection in ceiling void room and floor void applications.The extensive configuration options of the Sigma A-XT allow the functionality of the system to be extensively modified. The panel contains a large LED display to enable easy configuration and control which also displays the time remaining until release for added user safety.The countdown time is duplicated on up to seven remote status units to provide local indication of the system status.With all the electronics mounted on a single easily removable steel plate Sigma A-XT panels are both robust and easy to install. Sigma A-XT is supplied in an enclosure that matches the design and colour of the Elite RS range and is available in standard red or optional grey.The K16400M2 from the extensive range of Kentec products is a syncro IO expansion card enclosure with 5.25A power supply. flexibility to create customised IO panel.Key FeaturesUL864 and FM ListedThree initiation circuits as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage NAC delaysConfigurable detection delaysZero time delay upon manual release optionSupports up to seven four wire status indicatorsBuilt in Extract Fan controlCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable releasing delays up to 60 seconds in 5 second stopsConfigurable releasing duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining until release

GBP 628.31
1

Kentec K1810-44 Sigma A-XT Extinguishant Control Panel - 115V Grey

Kentec K1810-44 Sigma A-XT Extinguishant Control Panel - 115V Grey

Kentec K1810-44 Sigma A-XT Extinguishant Control Panel - 115V GreySigma A-XT releasing panel offers outstanding value and performance for all small to medium fixed fire-fighting installations.With three initiating circuits as standard release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three types of activations for detection in ceiling void room and floor void applications.The extensive configuration options of the Sigma A-XT allow the functionality of the system to be extensively modified. The panel contains a large LED display to enable easy configuration and control which also displays the time remaining until release for added user safety.The countdown time is duplicated on up to seven remote status units to provide local indication of the system status.With all the electronics mounted on a single easily removable steel plate Sigma A-XT panels are both robust and easy to install. Sigma A-XT is supplied in an enclosure that matches the design and colour of the Elite RS range and is available in standard red or optional grey.The K16400M2 from the extensive range of Kentec products is a syncro IO expansion card enclosure with 5.25A power supply. flexibility to create customised IO panel.Key FeaturesUL864 and FM ListedThree initiation circuits as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage NAC delaysConfigurable detection delaysZero time delay upon manual release optionSupports up to seven four wire status indicatorsBuilt in Extract Fan controlCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable releasing delays up to 60 seconds in 5 second stopsConfigurable releasing duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining until release

GBP 628.31
1

Kentec K1810-12 Sigma A-XT Extinguishant Control Panel 115V Red

Kentec K1810-12 Sigma A-XT Extinguishant Control Panel 115V Red

Kentec K1810-12 Sigma A-XT Extinguishant Control Panel 115V RedSigma A-XT releasing panel offers outstanding value and performance for all small to medium fixed fire-fighting installations.With three initiating circuits as standard release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three types of activations for detection in ceiling void room and floor void applications.The extensive configuration options of the Sigma A-XT allow the functionality of the system to be extensively modified. The panel contains a large LED display to enable easy configuration and control which also displays the time remaining until release for added user safety.The countdown time is duplicated on up to seven remote status units to provide local indication of the system status.With all the electronics mounted on a single easily removable steel plate Sigma A-XT panels are both robust and easy to install. Sigma A-XT is supplied in an enclosure that matches the design and colour of the Elite RS range and is available in standard red or optional grey.The K16400M2 from the extensive range of Kentec products is a syncro IO expansion card enclosure with 5.25A power supply. flexibility to create customised IO panel.Key FeaturesUL864 and FM ListedThree initiation circuits as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage NAC delaysConfigurable detection delaysZero time delay upon manual release optionSupports up to seven four wire status indicatorsBuilt in Extract Fan controlCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable releasing delays up to 60 seconds in 5 second stopsConfigurable releasing duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining until release

GBP 628.31
1

Kentec Sigma XT 3 Zone Single Area Extinguishant Control Panel to BS EN12094-1 K11031M2

Kentec Sigma XT 3 Zone Single Area Extinguishant Control Panel to BS EN12094-1 K11031M2

Kentec SigmaK11031M2XT 3 Zone Single Area Extinguishant Control Panel to BS EN12094-1Designed and manufactured to the highest standards in a quality controlled environment and with European EN12094-1 approvals the Sigma XT K11031M2 extinguishant releasing panel offers outstanding value and performance for all small to medium fixed fire-fighting installations. With three detection zones as standard extinguishant release can be configured to activate from any combination of detection zone inputs to allow among other combinations any two from three type activations such as would be required for detection in ceiling void room and floor void applications.The extensive configuration options of the Sigma XT K11031M2 allow the functionality of the system to be extensively modified while still complying with the requirements of the controlling standard for the equipment EN12094-1 EN54-2 and EN54-4. The panel contains a large LED display to enable easy configuration and control which also displays the time remaining until extinguishant release for added user safety. The countdown timer is duplicated on up to seven remote status units to provide local indication of the extinguishant system status. With all of the electronics mounted on a single easily removable steel plate Sigma XT panels are both robust and easy to install. Sigma XT is supplied in an enclosure that matches the design and colour of the Sigma CP range.Key FeaturesApproved to EN12094-1 EN54-2 and EN54-4Three detection zones as standardAny single zone or any combinations of zones can be configured to releaseConfigurable first stage sounder delaysConfigurable detection delaysZero time delay upon manual release optionCompatible with I.S. barriersNon-latching zone input option to receive signals from other systems such as aspirating equipmentConfigurable extinguishant delays up to 60 seconds in 5 second stepsConfigurable extinguishant duration up to 5 minutes in 5 second stepsCountdown timer shows time remaining until releaseSupports up to seven four wire status indicatorsBuilt in Extract Fan control

GBP 587.21
1