zigbee repeater from GBP 167 | See the cheapest prices and offers on css.lazzaweb.dk

Kentec K579 Syncro View Repeater Board

Kentec K579 Syncro View Repeater BoardThe K579 is a Repeater Board for the Syncro View.

GBP 334.70

1

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 Zone

Kentec Sigma CP-R 24v Repeater Panel with Low Profile Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsPart NumberDescriptionE01020L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 2 Zones SurfaceE01040L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 4 Zones SurfaceE01080L2Sigma CP-R Conventional Repeater Panel 24V version low profile enclosure 8 Zones Surface

GBP 201.43

1

Kentec Sigma CP-R Repeater Panel with 230v PSU amp Standard Enclosure 2 - 8 Zone

Kentec Sigma CP-R Repeater Panel with 230v PSU Standard Enclosure 2 - 8 ZoneThe Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesSigma CP-R Two wire serial connectionUp to 7 panels per system230V AC or 24V DC powered versionsFull control over main panelVolt free fire and fault contact outputsAncillary PCB Two wire serial connectionUp to 7 boards per system230V AC or 24V DC powered versionsOpen collector zonal fault outputsVolt free fire coincidence and common fault contact outputsVariants AvailablePart NumberDescriptionK01020M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 2 Zones SurfaceK01040M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 4 Zones SurfaceK01080M2Sigma CP-R Conventional Repeater Panel with PSU 230V standard enclosure 8 Zones Surface

GBP 295.45

1

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2

Kentec K01080M2 Sigma CP-R 8 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 366.24

1

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2

Kentec K01040M2 Sigma CP-R 4 - Zone Conventional Repeater Panel with PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Sigma CP-R Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs Ancillary PCB Two wire serial connection Up to 7 boards per system 230V AC or 24V DC powered versions Open collector zonal fault outputs Volt free fire coincidence and common fault contact outputs

GBP 304.18

1

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2

Kentec E01040L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 4 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 210.79

1

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2

Kentec E01080L2 Sigma CP-R Low Profile Enclosure Conventional Repeater Panel 8 Zone No PSU2The Sigma CP-R Repeater is compatible with all Sigma CP control panels which have operating software version V2.0 or above. Repeaters are available with 2 4 or 8 zones and in mains powered K versions or 24V powered E versions. Mains powered repeaters require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.A mixture of Repeaters Ancillary boards or Sounder Boards up to a maximum of 7 of each type can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key Features Two wire serial connection Up to 7 panels per system 230V AC or 24V DC powered versions Full control over main panel Volt free fire and fault contact outputs

GBP 254.51

1

Kentec MK67000M1 Syncro View Marine Local LCD Repeater Panel

Kentec MK67000M1 Syncro View Marine Local LCD Repeater PanelThe Syncro View Marine fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Syncro ASM fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Syncro ASM fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The Syncro View Marine is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro ASM control panel a maximum of 4 View Marine repeater panels in this combination or up to 15 View Marine repeater panels if powered local from an ancillary 24V DC supply or a 230V powered option with local battery back-up.Syncro View Marine is housed in a small enclosure which is styled similarly to the Syncro ASM control panel and is ideal for installations where a large fire control panel would be detrimental to dcor or where space is at a premium such as the Control Bridge or Helm.Up to 15 Syncro View Marine annunciators can be connected to each control panel on the Syncro ASM network making View Marine ideal where multiple points of indication andor control are required in such as places as engine rooms staff quarters living spaces or control areas.Key FeaturesUp to 15 annunciators can be connected to each Syncro ASM fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro ASM panel controlsSimple two-wire serial connectionSmall Syncro style enclosureRemovable electronics for easy installation24V DC or 230V AC power options

GBP 474.18

1

Kentec MK67000AM1 Syncro View Marine Repeater 24v Flat Plate Fascia

Kentec MK67000AM1 Syncro View Marine Repeater 24v Flat Plate FasciaThe Syncro View Marine fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Syncro ASM fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Syncro ASM fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The Syncro View Marine is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro ASM control panel a maximum of 4 View Marine repeater panels in this combination or up to 15 View Marine repeater panels if powered local from an ancillary 24V DC supply or a 230V powered option with local battery back-up.Syncro View Marine is housed in a small enclosure which is styled similarly to the Syncro ASM control panel and is ideal for installations where a large fire control panel would be detrimental to dcor or where space is at a premium such as the Control Bridge or Helm.Up to 15 Syncro View Marine annunciators can be connected to each control panel on the Syncro ASM network making View Marine ideal where multiple points of indication andor control are required in such as places as engine rooms staff quarters living spaces or control areas.Key FeaturesUp to 15 annunciators can be connected to each Syncro ASM fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro ASM panel controlsSimple two-wire serial connectionSmall Syncro style enclosureRemovable electronics for easy installation24V DC or 230V AC power options

GBP 499.58

1

Kentec MK67001M1 Syncro View Marine Local LCD Repeater Panel with Enable Key Switch

Kentec MK67001M1 Syncro View Marine Local LCD Repeater Panel with Enable Key SwitchThe Syncro View Marine fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Syncro ASM fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Syncro ASM fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The Syncro View Marine is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro ASM control panel a maximum of 4 View Marine repeater panels in this combination or up to 15 View Marine repeater panels if powered local from an ancillary 24V DC supply or a 230V powered option with local battery back-up.Syncro View Marine is housed in a small enclosure which is styled similarly to the Syncro ASM control panel and is ideal for installations where a large fire control panel would be detrimental to dcor or where space is at a premium such as the Control Bridge or Helm.Up to 15 Syncro View Marine annunciators can be connected to each control panel on the Syncro ASM network making View Marine ideal where multiple points of indication andor control are required in such as places as engine rooms staff quarters living spaces or control areas.Key FeaturesUp to 15 annunciators can be connected to each Syncro ASM fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro ASM panel controlsSimple two-wire serial connectionSmall Syncro style enclosureRemovable electronics for easy installation24V DC or 230V AC power options

GBP 499.58

1

Kentec Syncro View Marine Repeater 24v Flat Plate Fascia with Key Switch MK67001AM1

Kentec MK67001AM1 Syncro View Marine Repeater 24v Flat Plate Fascia with Key SwitchThe Syncro View Marine fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Syncro ASM fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Syncro ASM fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The Syncro View Marine is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro ASM control panel a maximum of 4 View Marine repeater panels in this combination or up to 15 View Marine repeater panels if powered local from an ancillary 24V DC supply or a 230V powered option with local battery back-up.Syncro View Marine is housed in a small enclosure which is styled similarly to the Syncro ASM control panel and is ideal for installations where a large fire control panel would be detrimental to dcor or where space is at a premium such as the Control Bridge or Helm.Up to 15 Syncro View Marine annunciators can be connected to each control panel on the Syncro ASM network making View Marine ideal where multiple points of indication andor control are required in such as places as engine rooms staff quarters living spaces or control areas.Key FeaturesUp to 15 annunciators can be connected to each Syncro ASM fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro ASM panel controlsSimple two-wire serial connectionSmall Syncro style enclosureRemovable electronics for easy installation24V DC or 230V AC power options

GBP 540.28

1

Kentec Syncro View Local LCD Repeater Panel cw Enable Controls Surface K67001M1

Kentec Syncro View Local LCD Repeater Panel cw Enable Controls Surface K67001M1The Syncro View fire alarm repeater provides a cost effective simple and convenient method of extending the controls and indications of the Syncro AS fire alarm control panel to other locations.The large graphic LCD brightness LED indicators and full set of controls duplicate the indications and controls on the Syncro AS fire alarm control panel at up to 15 additional locations via a separate to the Syncro AS network simple two-wire serial data connection.Ideal for locations where a control and indication point smaller than a full fire alarm control panel is required the Syncro VIiew is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro AS control panel auxiliary 24V DC supply or a 230V powered option with local battery backup.Key Features Up to 15 annunciators can be connected to each Syncro AS panelResponse or Syncro AS fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro panel controlsSimple two-wire serial connectionSmall enclosureRemovable electronics for easy installation24V DC or 230V AC power optionsLow power consumptionMulti language optionsConnection monitored by Syncro fire control panel

GBP 499.61

1

Kentec Syncro View Local LCD Repeater Panel cw 750 mA PSU Surface K67750M1

Kentec Syncro View Local LCD Repeater Panel cw 750 mA PSU Surface K67750M1The Syncro View fire alarm repeater provides a cost effective simple and convenient method of extending the controls and indications of the Syncro AS fire alarm control panel to other locations.The large graphic LCD brightness LED indicators and full set of controls duplicate the indications and controls on the Syncro AS fire alarm control panel at up to 15 additional locations via a separate to the Syncro AS network simple two-wire serial data connection.Ideal for locations where a control and indication point smaller than a full fire alarm control panel is required the Syncro VIiew is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro AS control panel auxiliary 24V DC supply or a 230V powered option with local battery backup.Key Features Up to 15 annunciators can be connected to each Syncro AS panelResponse or Syncro AS fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro panel controlsSimple two-wire serial connectionSmall enclosureRemovable electronics for easy installation24V DC or 230V AC power optionsLow power consumptionMulti language optionsConnection monitored by Syncro fire control panel

GBP 622.43

1

Kentec Syncro View Local LCD Repeater Panel cw Enable Controls amp 750 mA PSU Surface K67751M1

Kentec Syncro View Local LCD Repeater Panel cw Enable Controls 750 mA PSU Surface K67751M1The Syncro View fire alarm repeater provides a cost effective simple and convenient method of extending the controls and indications of the Syncro AS fire alarm control panel to other locations.The large graphic LCD brightness LED indicators and full set of controls duplicate the indications and controls on the Syncro AS fire alarm control panel at up to 15 additional locations via a separate to the Syncro AS network simple two-wire serial data connection.Ideal for locations where a control and indication point smaller than a full fire alarm control panel is required the Syncro VIiew is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro AS control panel auxiliary 24V DC supply or a 230V powered option with local battery backup.Key Features Up to 15 annunciators can be connected to each Syncro AS panelResponse or Syncro AS fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro panel controlsSimple two-wire serial connectionSmall enclosureRemovable electronics for easy installation24V DC or 230V AC power optionsLow power consumptionMulti language optionsConnection monitored by Syncro fire control panel

GBP 645.91

1

Kentec Syncro View Local LCD Repeater Panel K67000M1

Kentec Syncro View Local LCD Repeater PanelK67000M1Designed and manufactured to the highest standards in a quality controlled environment the Syncro VIEW fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Syncro fire alarm control panel to other locations. The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Syncro fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The Syncro VIEW is available in either a 24V DC powered option which can be powered via an additional 2 cores from the Syncro control panellocal 24V DC supply or a 230V powered option with local battery backup. Syncro VIEW is housed in a small enclosure which is styled similarly to the Syncro control panel and is ideal for installations where a large control panel would be detrimental to decor such as entrance halls. Up to 15 Syncro VIEW annunciators can be connected to each control panel on the Syncro network making VIEW ideal where multiple points of indication andor control are required such as nurses stations or shop units.Key FeaturesUp to 15 annunciators can be connected to each Syncro Syncro Response or Syncro AS fire control panel.Large liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all Syncro panel controlsSimple two-wire serial connectionSmall Syncro style enclosureRemovable electronics for easy installation24V DC or 230V AC power optionsLow power consumptionMulti language optionsConnection monitored by Syncro fire control panel

GBP 469.75

1

Kentec K1172-40 eView Analogue Addressable Repeater Panel Grey

Kentec K1172-40 eView Analogue Addressable Repeater Panel GreyDesigned and manufactured to the highest standards in a quality controlled environment the eVIEW fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Elite fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Elite fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The eVIEW is powered by 24V DC which can be via an additional 2 conductors from the control panel or local 24V DC listed supply. eVIEW is housed in a small enclosure which is styled similarly to the Elite control panel and is ideal for installations where a large control panel would be detrimental to dcor such as entrance halls. Up to 15 eVIEW annunciators can be connected to each control panel on the Elite network making eVIEW ideal where multiple points of indication andor control are required such as nurses stations or shop units.Key FeaturesUp to 15 annunciators can be connected to each Elite fire control panelLarge liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all panel controlsSimple two-wire serial connectionSmall Elite style enclosureRemovable electronics for easy installation24V DC poweredLow power consumptionMulti language optionsConnection supervised by Elite fire control panel

GBP 563.71

1

Kentec eView Local LCD Repeater Panels ULFM Approved K1172-10

Kentec eView Local LCD Repeater Panels ULFM ApprovedDesigned and manufactured to the highest standards in a quality controlled environment the eVIEW fire alarm annunciator provides a simple and convenient method of extending the controls and indications of the Elite fire alarm control panel to other locations.The large graphic liquid crystal display and high brightness LED indicators duplicate the indications on the Elite fire alarm control panel at up to 15 additional locations via a simple two-wire serial data connection.The eVIEW is powered by 24V DC which can be via an additional 2 conductors from the control panel or local 24V DC listed supply. eVIEW is housed in a small enclosure which is styled similarly to the Elite control panel and is ideal for installations where a large control panel would be detrimental to dcor such as entrance halls. Up to 15 eVIEW annunciators can be connected to each control panel on the Elite network making eVIEW ideal where multiple points of indication andor control are required such as nurses stations or shop units.Standard FeaturesAvailable in Red or GrayUp to 15 annunciators can be connected to each Elite fire control panelLarge liquid crystal display 240 x 64 pixelsHigh brightness LED indicationsInternal sounderReplicates all panel controlsSimple two-wire serial connectionSmall Elite style enclosureRemovable electronics for easy installation24V DC poweredLow power consumptionMulti language optionsConnection supervised by Elite fire control panel

GBP 563.71

1

Kentec K1822-40 Boxed Sigma A-XT Ancillary PCB Grey

Kentec K1822-40 Boxed Sigma A-XT Ancillary PCB GreyThe Sigma A-XT Ancillary Board is compatible with all Sigma A-XT control panels. The board provides volt-free normally-open contacts enabling control of sub-systems and plant remotely from the main panel over a two-wire data bus.Ancillary boards require only a two-core data cable from the main control panel and a two-core power cable from the main panel.Up to seven Ancillary boards can be connected to a control panel and each is allocated an address from one to seven using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 4000 feet.A mixture of status units and Ancillary boards up to a maximum of seven of each type can be connected to the serial data bus.

GBP 234.90

1

Kentec K1822-10 Boxed Sigma A-XT Ancillary PCB Red

Kentec K1822-10 Boxed Sigma A-XT Ancillary PCB RedThe Sigma A-XT Ancillary Board is compatible with all Sigma A-XT control panels. The board provides volt-free normally-open contacts enabling control of sub-systems and plant remotely from the main panel over a two-wire data bus.Ancillary boards require only a two-core data cable from the main control panel and a two-core power cable from the main panel.Up to seven Ancillary boards can be connected to a control panel and each is allocated an address from one to seven using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 4000 feet.A mixture of status units and Ancillary boards up to a maximum of seven of each type can be connected to the serial data bus.

GBP 234.90

1

Kentec K04000M2 Sigma CP Sounder PCB - Boxed

Kentec K04000M2 Sigma CP Sounder PCB - BoxedThe Sigma K04000M2 is a sounder controller PCB in a steel enclosure which requires a 24v DC power source.The Kentec Sigma CP Sounder Board is compatible with all Sigma CP control panels which have operating software version V3.0 or above.The board provides 8 additional sounder outputs which can be configured as zoned 2-stage or common alarm.All sounder outputs are open and short circuit monitored and any faults on the sounder outputs will be announced at the main fire alarm panel as a sounder fault.A class change input is provided which when activated by a volt free contact closing will switch all sounder outputs on.Mains powered units require only a two core data cable from the main control panel. 24V DC versions require an additional two cores from another 24V DC source which is suitably rated to supply the total sounder current. 230V versions have their own power supply which is rated to supply sounder loads up to 5.25 Amps.Up to 7 Sounder boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. Sounder boards may be connected to the Sigma CP serial bus in addition to Sigma CP ancillary boards and Sigma CP-R repeater panels.The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres. Once Sounder boards have been recognised by the main panel a fault will be announced at the main panel if any become disconnected.Key FeaturesTwo wire serial connectionUp to 7 sounder boards per system24V DC powered - in steel enclosureZoned 2-stage or common alarmAll outputs monitored for open and short circuit faultsIndividual open and short circuit fault indicatorsFully monitored by main control panelClass change input facilityUp to 8 outputs with 1A available from eachCan be connected to serial bus with Ancillary boards and repeatersPower fault input for monitoring remote power supplies

GBP 246.64

1

Kentec K04400M2 Sigma CP Sounder PCB - Boxed

Kentec K04400M2 Sigma CP Sounder PCB - BoxedThe Sigma K04400M2 is a sounder controller PCB in a steel enclosure which requires a 230V DC power source.The Kentec Sigma CP Sounder Board is compatible with all Sigma CP control panels which have operating software version V3.0 or above.The board provides 8 additional sounder outputs which can be configured as zoned 2-stage or common alarm.All sounder outputs are open and short circuit monitored and any faults on the sounder outputs will be announced at the main fire alarm panel as a sounder fault.A class change input is provided which when activated by a volt free contact closing will switch all sounder outputs on.Mains powered units require only a two core data cable from the main control panel. 24V DC versions require an additional two cores from another 24V DC source which is suitably rated to supply the total sounder current. 230V versions have their own power supply which is rated to supply sounder loads up to 5.25 Amps.Up to 7 Sounder boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. Sounder boards may be connected to the Sigma CP serial bus in addition to Sigma CP ancillary boards and Sigma CP-R repeater panels.The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres. Once Sounder boards have been recognised by the main panel a fault will be announced at the main panel if any become disconnected.Key FeaturesTwo wire serial connectionUp to 7 sounder boards per system24V DC powered - in steel enclosureZoned 2-stage or common alarmAll outputs monitored for open and short circuit faultsIndividual open and short circuit fault indicatorsFully monitored by main control panelClass change input facilityUp to 8 outputs with 1A available from eachCan be connected to serial bus with Ancillary boards and repeatersPower fault input for monitoring remote power supplies

GBP 522.61

1

Kentec K1822-00 Sigma A-XT Ancillary PCB

Kentec K1822-00 Sigma A-XT Ancillary PCBThe Sigma A-XT Ancillary Board is compatible with all Sigma A-XT control panels. The board provides volt-free normally open contacts enabling control of sub systems and plant remotely from the main panel over a two-wire data bus.Ancillary boards require only a two-core data cable from the main control panel and a two-core power cable from the main panel.Up to seven ancillary boards can be connected to a control panel and each is allocated to an address from one to seven using a binary coded DIL switch.The total length of the data cable from the main panel to the last repeater must not exceed 4000 feet.A mixture of status units and Ancillary boards up to a maximum of seven of each type can be connected to the serial data bus.Key FeaturesTwo-wire serial connectionUp to seven per systemVolt-free relay outputs for fire and releasing system statusRelay operated LED indicatorsUL864 and FM listed

GBP 166.76

1

Kentec Boxed Sigma XT Ancillary PCB Surface K03000M2

Kentec Boxed Sigma XT Ancillary PCB Surface K03000M2The Sigma XT Ancillary Board is compatible with all Sigma XT control panels which have operating software version SIGXT_11A.HEX or above.The board provides volt free normally open contacts allowing control of subsystems and plant remotely from the main panel over a two-wire data bus.Mains powered boxed Ancillary boards require only a two-core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.Up to 7 Ancillary boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 per system230V AC or 24V DC powered versionsVolt free relay outputs for fire and extinguishing system statusRelay operated LED indicators

GBP 240.76

1

Kentec Boxed Sigma XT Ancillary PCB cw 0.75 A PSU Surface K03750M2

Kentec Boxed Sigma XT Ancillary PCB cw 0.75 A PSU Surface K03750M2The Sigma XT Ancillary Board is compatible with all Sigma XT control panels which have operating software version SIGXT_11A.HEX or above.The board provides volt free normally open contacts allowing control of subsystems and plant remotely from the main panel over a two-wire data bus.Mains powered boxed Ancillary boards require only a two-core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.Up to 7 Ancillary boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres.Key FeaturesTwo wire serial connectionUp to 7 per system230V AC or 24V DC powered versionsVolt free relay outputs for fire and extinguishing system statusRelay operated LED indicators

GBP 328.82

1

Kentec Sigma XT Ancillary Card K588

Kentec Sigma XT Ancillary Card K588The Sigma XT Ancillary Board is compatible with all Sigma XT control panels which have operating software version SIGXT_11A. HEX or above. The board provides volt free normally open contacts allowing control of sub-systems and plant remotely from the main panel over a two wire data bus. Mains powered boxed Ancillary boards require only a two core data cable from the main control panel. 24V DC versions require an additional two cores for power either from the main panel or from another 24V DC source.Up to 7 Ancillary boards can be connected to a control panel and each is allocated an address from 1 to 7 using a binary coded DIL switch. The total length of the data cable from the main panel to the last repeater must not exceed 1200 metres. A mixture of status units and Ancillary boards up to a maximum of 7 of each type can be connected to the serial data bus.Key FeaturesTwo wire serial connectionUp to 7 per system230V AC or 24V DC powered versionsVolt free relay outputs for fireand extinguishing system statusRelay operated LED indicators

GBP 170.29

1

Awardvindende Google Marketing Powerhouse

Brand

Merchant

Price (EUR)