455 results (0,13031 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Vimpex 10-2410WSX-S Surface Mount Identifire Alarm System Connection Box White

Vimpex 10-2410WSX-S Surface Mount Identifire Alarm System Connection Box White

Vimpex 10-2410WSX-S Surface Mount Identifire Alarm System Connection Box White TheVimpex 10-2410WSX-S is a white fire alarm connection box supplied with a surface mounting backbox from the Identifire range of products.This connection box provides a method for jointing fire alarm system cables in a clearly defined method.It supports cables up to2.5mm sq. and can join up to 4 separate conductors i.e. sounder circuit and detection circuit. Each connection box provides a very low resistance in order to minimise any volt-drop.VIMPEX 10-2410WSX-S IDENTIFIRE FIRE ALARM CONNECTION BOX SPECIFICATIONMaximum Conductor Size 2.5mm Sq. per terminalTypical Resistance Through Unit12 m ohmnMaximum Current Per Terminal 2AMaximum Voltage50 V dcOperating Temperature-5 to 50 Degrees CelsiusOperating Humidity95 non-condensingMaterial Fire Rated ABSInstallation Knockouts 4 x 20mm Round 1 x Rectangular

GBP 10.84
1

Vimpex Signaline SL-UCB Universal Connection Box

Vimpex Signaline SL-UCB Universal Connection Box

Vimpex Signaline SL-UCB Universal Connection Box for Signaline Linear Heat Detection Cables and Controllers Use for EOL Junction Box or Interposing Line UnitThe Signaline Universal Connection Box is suitable for use with all variants of Signaline FT-68 FT-88 FT-105 and HD. It can be used as an end of line enclosure junction box or an interposing line unit. This all-in-one solution reduces on site time and cost. It uses heat rated terminals and glands can be used with any Signaline linear heat detector.The IP66 rated enclosure provides a quick and efficient method to interconnect terminate and join lengths of any Signaline heat sensing cable. It can also be used for connecting the incoming leader cable to the start of a length of heat sensing cable.It is supplied with cable glands 1x terminal block 1x 470ohm resistor and 1x 680ohm resistor. Included resistors allow a Signaline FT cable to be connected directly to the zone terminals of most conventional fire control panels.The Signaline UCB is suitable for use with these cablesSignaline FT-68Signaline FT-68-RSignaline FT-88Signaline FT-88-RSignaline FT-105Signaline FT-105-RSignaline HDSignaline HD-RSignaline HD-SKey FeaturesIP Rating IP66Dimensions excluding cable glands 94 x 94 x 57 mmMaterial Impact and flame resistant polycarbonateColour RAL 7035 GreyChemical resistance Resistant to most acids alkalis and oilsOperating Temp -35C to 120C

GBP 61.58
1

Vimpex 10-2410RSX-S Identifire Surface Alarm System Red Connection Box

Vimpex 10-2410RSX-S Identifire Surface Alarm System Red Connection Box

Vimpex 10-2410RSX-S Identifire Surface Alarm System Red Connection BoxThe 10-2410RSX-S is a red fire alarm connection box supplied with a surface mounting backbox from the Identifire range of products.This connection box provides a method for jointing fire alarm system cables in a clearly defined method.It supports cables upto 2.5mm sq. and can join up to 4 separate conductors i.e. sounder circuit and detection circuit. Each connection box provides a very low resistance in order to minimise any volt drop.Key FeaturesConsistent Identifire DesignCan be printed for easy identificationMaterial Fire Rated ABSInstallation Knockouts 4 x 20mm Round 1 x Rectangular

GBP 10.84
1

Vimpex SL-HDP-JB Signaline HD JB Programmable Linear Heat Cable Junction Box

Vimpex SL-HDP-JB Signaline HD JB Programmable Linear Heat Cable Junction Box

Vimpex SL-HDP-JB Signaline HD JB Programmable Linear Heat Cable Junction BoxSignaline HD is a programmable Linear Heat Detector. It offers users the ability to set their own alarm temperatures as well as a pre-alarm feature and rate-of-rise alarm. Signaline HD linear heat detection system uses a special sensor cable. This cable runs along the entire area that needs protection. It works as a continuous heat sensor. It can detect temperature changes anywhere along its length due to resistance changes within the sensor cable.The Signaline HD system has a smart control unit. This unit checks the sensor cable for temperature changes all the time. Users can set specific alarm rules in the control unit. This lets them adjust the system based on the area level of risk approval standard and alarm temperature required. Where needed you can connect two lines of cable or leader cable to Signaline HD Sensor cable. To do this the Signaline HD JB should be used. This IP rated and high impact resistance box provides a secure and easy connection between two lines of cable.

GBP 135.56
1

Vimpex SG-BBC Clear Weatherproof Back Box for SmartGuard

Vimpex SG-BBC Clear Weatherproof Back Box for SmartGuard

Vimpex SG-BBC Clear Weatherproof Back Box for SmartGuardThe SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesColour WhiteDesigned to enclose most EN 54-11 approved call points and emergency switchesAdd greater protection to rain water dustFor use with SmartGuard flush mount protectors2 knockouts for 20 mm conduitHeight 190mmWidth 119mmDepth 40mm

GBP 14.83
1

Vimpex SG-BBCS-G SmartGuard Green Sounder Weatherproof Back Box - Clear

Vimpex SG-BBCS-G SmartGuard Green Sounder Weatherproof Back Box - Clear

Vimpex SG-BBCS-G SmartGuard Green Sounder Weatherproof Back Box - ClearThe SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour GreenClearWeatherproof

GBP 71.30
1

Vimpex SG-BBCS-W SmartGuard White Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-W SmartGuard White Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-W SmartGuard White Sounder Weatherproof Back Box ClearThe SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour WhiteClearWeatherproofPlease note The image is for illustrative purposes only.

GBP 71.30
1

Vimpex SG-BBCS-Y SmartGuard Yellow Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-Y SmartGuard Yellow Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-Y SmartGuard Yellow Sounder Weatherproof Back Box Clear The SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour YellowClearWeatherproofPlease note The image is for illustrative purposes only.

GBP 71.30
1

Vimpex SG-BBCS-R SmartGuard Red Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-R SmartGuard Red Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-R SmartGuard Red Sounder Weatherproof Back Box Clear The SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour RedClearWeatherproofPlease note The image is for illustrative purposes only.

GBP 71.30
1

Vimpex SG-BBCS-B SmartGuard Blue Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-B SmartGuard Blue Sounder Weatherproof Back Box Clear

Vimpex SG-BBCS-B SmartGuard Blue Sounder Weatherproof Back Box Clear The SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour BlueClearWeatherproofPlease note The image is for illustrative purposes only.

GBP 71.30
1

Vimpex SG-BBC-R SmartGuard Red No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-R SmartGuard Red No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-R SmartGuard Red No Sounder Weatherproof Back Box Clear The SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour ClearWaterproofPlease note The image is for illustrative purposes only.

GBP 22.36
1

Vimpex SG-BBC-G SmartGuard Green No Sounder Weatherproof Back Box - Clear

Vimpex SG-BBC-G SmartGuard Green No Sounder Weatherproof Back Box - Clear

Vimpex SG-BBC-G SmartGuard Green No Sounder Weatherproof Back Box - ClearThe SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour clearWeatherproofPlease note The image is for illustrative purposes only.

GBP 22.36
1

Vimpex SG-BBC-W SmartGuard White No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-W SmartGuard White No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-W SmartGuard White No Sounder Weatherproof Back Box ClearThe SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour WhiteClearWeatherproofPlease note The image is for illustrative purposes only.

GBP 22.36
1

Vimpex SG-BBC-Y SmartGuard Yellow No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-Y SmartGuard Yellow No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-Y SmartGuard Yellow No Sounder Weatherproof Back Box Clear The SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour ClearWeatherproofPlease note The image is for illustrative purposes only.

GBP 22.36
1

Vimpex SG-BBC-B SmartGuard Blue No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-B SmartGuard Blue No Sounder Weatherproof Back Box Clear

Vimpex SG-BBC-B SmartGuard Blue No Sounder Weatherproof Back Box Clear The SmartGuard Back Box is a fully enclosed mounting box designed to give even greater protection from rain and water ingress when used with the SmartGuard flush mount products.Key FeaturesDesigned to enclose most EN 54-11 approved call points and emergency switchesGreater protection from water and dust2 knockouts for 20 mm conduitColour BlueClearWeatherproofPlease note The image is for illustrative purposes only.

GBP 22.36
1

Vimpex VPSU-BB Floor Standing Battery Box For 2 X 65Ah Batteries

Vimpex VPSU-BB Floor Standing Battery Box For 2 X 65Ah Batteries

Vimpex VPSU-BB Floor Standing Battery Box For 2 X 65Ah BatteriesThe new 24 V EB range of switch mode power supplies has been specifically designed for EN54 compliant fire systems.Available in either 1 2 5 8 10 Amp versions they are certified by UL to EN54-4 1997 A1 2002 A22006.The units include intelligent battery charging using EcoCharge Technology possess mains and battery monitoring with independent volt-free outputs and also feature battery deep discharge protection in the event of a prolonged mains failure.The inclusion of LED indicators provides quick diagnostics of the status of the power supply while a variety of enclosures offer the installer a choice of standby battery backup options see table.Key Features27.6 V dc outputCost effective switch mode technologyEnergy efficientUp to 88.5 efficiencyMore efficient in operationPower savingLonger field lifeLess prone to failureIntelligent battery charging and monitoring with EcoCharge TechnologyRemote fault signallingFull rated current to load plus additional current for battery chargingDeep discharge protectionLED IndicationMains statusOutput or battery fuse failOutput short circuit or low voltageBattery low or missingVolt-free fault output - EPSMains failVolt-free fault output - PSU fault Battery faultCharger fault Loss of outputMains Transient protection 10 Amp version can charge up to 2 x 65 Ah batteries housed in a separate enclosure VPSU-BBThree-year warranty

GBP 323.40
1

Vimpex 10-1310RSW-S Identifire Surface VID Red Body Clear Lens

Vimpex 10-1310RSW-S Identifire Surface VID Red Body Clear Lens

Vimpex 10-1310RSW-S Identifire Surface VID Red Body Clear LensThe Identifire VID Beacon uses high quality LEDs to provide a beaconstrobe suitable for all general signalling and ancillary fire signalling.Identifire is an installers dream offering flexibility consistency and style. The Identifire VID Beacon with Clear Lens is provided with a surface mount back box but can be mounted flush with the use of a standard electrical back box.Where surface mounting is required the Identifire back box is specifically designed to fit onto all electrical back boxes with knock-out fixing holes for ease of installation. This back box also accepts conduit entry and use of cable glands.Key Features10-1310RSW-SRed box with clear lensVery bright VID beaconIdeal for many general signalling applicationsCan be surface mounted with the provided Identifire back boxCan be flush mounted with a standard electrical gang boxCan be grid mounted for industrial applications

GBP 22.81
1

Vimpex 10-1310WFB-S Identifire Flush VID White Body Blue Lens

Vimpex 10-1310WFB-S Identifire Flush VID White Body Blue Lens

Vimpex 10-1310WFB-S Identifire Flush VID White Body Blue LensThe Identifire VID Beacon uses high quality LEDs to provide a beaconstrobe suitable for all general signalling and ancillary fire signalling.Identifire is an installers dream offering flexibility consistency and style. The Identifire VID Beacon with Clear Lens is provided with a surface mount back box but can be mounted flush with the use of a standard electrical back box.Where surface mounting is required the Identifire back box is specifically designed to fit onto all electrical back boxes with knock-out fixing holes for ease of installation. This back box also accepts conduit entry and use of cable glands.Key Features10-1310RSW-SRed box with clear lensVery bright VID beaconIdeal for many general signalling applicationsCan be surface mounted with the provided Identifire back boxCan be flush mounted with a standard electrical gang boxCan be grid mounted for industrial applications

GBP 20.83
1

Vimpex 10-2111WSR-S Identifire Surface Remote Indicator Unit with Buzzer

Vimpex 10-2111WSR-S Identifire Surface Remote Indicator Unit with Buzzer

Vimpex 10-2111WSR-S Identifire Surface Remote Indicator Unit with BuzzerThe 10-2111WSR-S is a bright LED indicator with buzzer suitable for use as a local alarmindicator.Identifire is an installers dream offering flexibility consistency and style. The Identifire Remote Lamp Unit with Buzzer is provided with a surface mount back box but can be mounted flush with the use of a standard electrical back box.Where surface mounting is required the Identifire back box is specifically designed to fit onto all electrical back boxes with knock-out fixing holes for ease of installation. This back box also accepts conduit entry and use of cable glands.Key FeaturesVery bright easily visible LED80 dBA buzzerIdeal for use as a local alarmindicatorMade from fire rated ABSIdeal for nurse stations theatres and building control offices

GBP 16.87
1

Vimpex 10-1110WSW-S Identifire Surface Tritone Sounder VID White Body Clear Lens

Vimpex 10-1110WSW-S Identifire Surface Tritone Sounder VID White Body Clear Lens

Vimpex 10-1110WSW-S Identifire Surface Tritone Sounder VID White Body Clear LensIdentifire is an installers dream offering consistency familiarity and therefore speed of installation.Where surface mounting is required the Identifire surface back box is specifically designed to fit onto all electrical back boxes with knock-out fixing holes for ease of installation. Our back box also accepts conduit entry and use of cable glands.Our VID design is superior in performance with very bright LEDs and consistent performance across lens colours. If a VAD is not required use of our TriTone with VID visual alarm device will mean that the beacon is clearly visible when required.Key FeaturesCompliant to EN 54 Part 3Very Bright VID beaconCombines Sound and VIDFlush or surface mountedWhite BodyClear Lens

GBP 29.77
1