692 results (0,15869 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Carrier 5150-W 2-Wire On-The-Glass Piezo Sensor With 30 cm Wire Leads NC Alarm Output

Carrier 5150-W 2-Wire On-The-Glass Piezo Sensor With 30 cm Wire Leads NC Alarm Output

Carrier 5150-W 2-Wire On-The-Glass Piezo Sensor With 30 cm Wire Leads NC Alarm OutputThe Sentrol 5150 series glass break detector has been designed using the latest electronic techniques. This enables the detector to contain all the necessary circuitry for excellent detection whilst filtering out and rejecting all unwanted signals that would normally result in a nuisance alarms e.g. ultra-sound radio frequency interference etc. The 5150 series will provide a 3 m radius of protection. Suitable for use on standard window glass plate wired tempered and laminated glass.Due to the design of the product the detector may be fitted as close as 2.5 cm from the window frame and still provide a full 3 m radius. The 5150 series detectors are passive sensors therefore any number of detectors may be installed on the same windowpane without the risk of interaction. The detectors use a fail-safe normally closed open to alarm relay contact enabling compatibility with any standard burglar alarm control equipment.The output from the relay contact should be connected via the alarm 24-hour tamper loop in order to provide early signalling at the control whether the alarm is switched on or off. The opening of the normally closed relay contact signals the alarm.Easily installs with pre-cut specially formulated 3M adhesive tape.Key Features3 m radius of coverage measured from the sensorProtects all glass types up to a standard thickness of 6.4 mm includingplate wired tempered and laminated glassIdeal for 24-hours loop protectionTwo wire sensor drawing no power from the loopCompatible with most wireless transmitters

GBP 12.82
1

Carrier 5150-M 2-Wire On-The-Glass Piezo Sensor With 30 cm Wire Leads NC Alarm Output

Carrier 5150-M 2-Wire On-The-Glass Piezo Sensor With 30 cm Wire Leads NC Alarm Output

Carrier 5150-M 2-Wire On-The-Glass Piezo Sensor With 30 cm Wire Leads NC Alarm OutputThe Sentrol 5150 series glass break detector has been designed using the latest electronic techniques. This enables the detector to contain all the necessary circuitry for excellent detection whilst filtering out and rejecting all unwanted signals that would normally result in a nuisance alarms e.g. ultra-sound radio frequency interference etc. The 5150 series will provide a 3 m radius of protection. Suitable for use on standard window glass plate wired tempered and laminated glass.Due to the design of the product the detector may be fitted as close as 2.5 cm from the window frame and still provide a full 3 m radius. The 5150 series detectors are passive sensors therefore any number of detectors may be installed on the same windowpane without the risk of interaction. The detectors use a fail-safe normally closed open to alarm relay contact enabling compatibility with any standard burglar alarm control equipment.The output from the relay contact should be connected via the alarm 24-hour tamper loop in order to provide early signalling at the control whether the alarm is switched on or off. The opening of the normally closed relay contact signals the alarm.Easily installs with pre-cut specially formulated 3M adhesive tape.Key Features3 m radius of coverage measured from the sensorProtects all glass types up to a standard thickness of 6.4 mm includingplate wired tempered and laminated glassIdeal for 24-hours loop protectionTwo wire sensor drawing no power from the loopCompatible with most wireless transmitters

GBP 13.24
1

Zeta ZT-CP4F CP4 Indoor Call Point Flush

Zeta ZT-CP4F CP4 Indoor Call Point Flush

Zeta ZT-CP4F CP4 Indoor Call Point FlushA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesFlush mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installation

GBP 13.10
1

Zeta ZT-CP4Y CP4 Indoor Call Point Surface - Yellow

Zeta ZT-CP4Y CP4 Indoor Call Point Surface - Yellow

Zeta ZT-CP4Y CP4 Indoor Call Point Surface - YellowA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesSurface mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour Yellow

GBP 15.12
1

Zeta ZT-CP4W CP4 Indoor Call Point Surface - White

Zeta ZT-CP4W CP4 Indoor Call Point Surface - White

Zeta ZT-CP4W CP4 Indoor Call Point Surface - WhiteA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesSurface mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour White

GBP 15.12
1

Zeta ZT-CP4 CP4 Indoor Call Point Surface

Zeta ZT-CP4 CP4 Indoor Call Point Surface

Zeta ZT-CP4 CP4 Indoor Call Point SurfaceA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesSurface mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installation

GBP 12.82
1

Zeta ZT-CP4G CP4 Indoor Call Point Surface - Green

Zeta ZT-CP4G CP4 Indoor Call Point Surface - Green

Zeta ZT-CP4G CP4 Indoor Call Point Surface - GreenA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesSurface mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour Green

GBP 15.12
1

Zeta ZT-CP4B CP4 Indoor Call Point Surface - Blue

Zeta ZT-CP4B CP4 Indoor Call Point Surface - Blue

Zeta ZT-CP4B CP4 Indoor Call Point Surface - BlueA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesSurface mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour Blue

GBP 15.12
1

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APO

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APO

Apollo Series 65 Optical Smoke Detector with Flashing LED 55000-316APOThe Series 65 Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector and has an indicator LED which is clear in quiescent state but produces a red light in alarm.OperationThe Series 65 Optical Smoke Detector has a moulded self-extinguishing white polycarbonate case with wind resistant smoke inlets. Nickel-plated stainless-steel wiper contacts connect the detector to the base. Inside the case a printed circuit board has the optical system mounted on one side and the signal processing electronics on the other. The sensing chamber is a black moulding configured as a labyrinth which prevents penetration of ambient light.The labyrinth has a fine gauze insect-resistant cover. The chamber houses an infrared light emitting diode LED and a photo-diode which has an integral visible-light filter as extra protection against ambient light. Every three seconds the LED emits a burst of collimated light modulated at 4kHz. In clear air light from the LED does not fall directly on the diode because the LED is positioned at an obtuse angle to the diode. When smoke enters the chamber a fraction of the collimated light is scattered onto the photo-diode.If the resulting signal from the photo-diode is above a pre-set threshold the LED emits two more bursts of light this time at two-second intervals. If light is scattered onto the photo-diode by both these pulses due to the presence of smoke the detector signals an alarm state by switching the alarm latch on increasing the current drawn from the supply from about 40A to a maximum of 75mA. This fall in the impedance of the detector is recognised by the control panel as an alarm signal. The alarm current also illuminates the detector integral LED. A remote indicator connected between the L1 IN terminal and the R terminal will have a voltage equal to the supply voltage less 1 volt across it and so will illuminate.To ensure correct operation of the detector the control panel must be arranged to supply a maximum of 33 Volts dc and a minimum of 9 Volts dc in normal operation.The supply may fall to 6 Volts dc in alarm conditions if a supply current of at least 10mA is available at this voltage. To ensure effective illumination of the integral LED and any remote indicator the supply to the detector should exceed 12 Volts. To restore the detector to quiescent condition it is necessary to expel any smoke and interrupt the electrical supply to the detector for a minimum of one second.Key FeaturesResponds well to slow-burning smouldering firesWell-suited to bedrooms and escape routesUnaffected by wind or atmospheric pressureFlashing LED and magnet operated test switch option

GBP 16.52
1

Kidde N-MC-FE Glass Trigger Element For Intelligent Manual Call Points Pack of 10

Kidde N-MC-FE Glass Trigger Element For Intelligent Manual Call Points Pack of 10

Kidde N-MC-FE Glass Trigger Element For Intelligent Manual Call Points Pack of 10The N-MC-FE is a glass trigger element for compatible Type-A series manual call points. It may be used as alternative for resettable elements that are normally used in these manual call points. The N-MC-FE allows the manual call point to be easily activated without the need for tools.The N-MC-FE uses clear black print on a brilliant white background. An arrow on either side pointing inwards towards a dot indicates to the operator where to push on the element to activate the manual call point.Installation of the frangible element in a compatible manual call point is made easy by the design of the manual call point. Using the test key the front cover of the manual call point is removed allowing the insertion of the N-MC-FE with a quick and simple action.The coated glass element is designed to break easily and safely across a vertical running break guide consistently in the same place. Little force is required to break the element eliminating the need for special tools to facilitate activation. The glass coating ensures no splintering of the glass avoiding possible injury to the operator during the activation process.Key FeaturesQuick installation without special toolsEasy to retrofitCoated glass prevents operator injury by controlling the glass break and avoiding glass fragmentsEasy break glass for smooth and consistent breaks in the same positionEasy to operate without the need for hammersEN54 certified with compatible manual call points

GBP 15.40
1

Carrier IU987-25PK XPERT Card Non-Addressed Apollo equivalent 38531-771 Pack of 25

Carrier IU987-25PK XPERT Card Non-Addressed Apollo equivalent 38531-771 Pack of 25

Carrier IU987-25PK XPERT Card Non-Addressed Apollo equivalent 38531-771 Pack of 25The IU987 is a replacement un-addressed address card for use in 900 bases for 900 series detectors. This card provides a unique patented addressing method with simple user friendly and accurate identification of a detectors location.The IU987 a plastic coded card containing seven pips. The address is set by simply removing the pips with a screwdriver according to a chart supplied with the bases. The coded card is then inserted into the side of the base where it locks into position. When the detector head is rotated into the base the remaining pips on the card operate the address buttons on the base of the detector and the address is read by the detector electronics.Addressing in this manner simplifies and speeds up installation and commissioning and can be used on Series 930 950 970 and 990 device ranges.Address information is held in the detector base not the detector head. This means that the address remains in the same location regardless of how many times the detector head is replaced for example during servicing or maintenance. It also allows for different types of detecting heads to be interchanged to meet changes in building use without changing the address location.Key FeaturesPack of 25Easy addressing

GBP 17.42
1

Solo 460 Heat Detector Tester Baffle for Fike Detectors 15-0239

Solo 460 Heat Detector Tester Baffle for Fike Detectors 15-0239

Solo 460 Heat Detector Tester Baffle for Fike Detectors 15-0239Due to the uniquely shaped detector chambers on Fike detectors the manufacturers developed a baffle to aid testing. the baffle is designed for the Solo 460 heat detector tester head unit and changes the direction of the direct heat flow to ensure a complete and effective test when testing Fike detectors. The baffle is inserted at the top of the Solo 460 as illustrated in the picture above.Please note Baffle only for use with Fike Detectors please remove when testing other detectors allowing for the direct heat flow to return to its standard format.

GBP 11.76
1

Zeta ZT-CP4FW CP4 Indoor Call Point Flush Mount - White

Zeta ZT-CP4FW CP4 Indoor Call Point Flush Mount - White

Zeta ZT-CP4FW CP4 Indoor Call Point Flush Mount - WhiteA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesFlush mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour White

GBP 15.12
1

Zeta ZT-CP411G CP4 Conventional Surface Mount Manual Call Point - Double Pole - Green

Zeta ZT-CP411G CP4 Conventional Surface Mount Manual Call Point - Double Pole - Green

Zeta ZT-CP411G CP4 Conventional Surface Mount Manual Call Point - Double Pole - GreenA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesSurface mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour GreenDouble pole

GBP 16.15
1

Zeta ZT-CP4FY CP4 Indoor Call Point Flush Mount - Yellow

Zeta ZT-CP4FY CP4 Indoor Call Point Flush Mount - Yellow

Zeta ZT-CP4FY CP4 Indoor Call Point Flush Mount - YellowA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesFlush mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour Yellow

GBP 15.12
1

Zeta ZT-CP411 CP4 Conventional Surface Mount Manual Call Point - Double Pole - Red

Zeta ZT-CP411 CP4 Conventional Surface Mount Manual Call Point - Double Pole - Red

Zeta ZT-CP411 CP4 Conventional Surface Mount Manual Call Point - Double Pole - RedA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesSurface mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour RedDouble pole

GBP 16.15
1

Zeta ZT-CP4F11 CP4 Conventional Flush Mount Manual Call Point - Double Pole - Red

Zeta ZT-CP4F11 CP4 Conventional Flush Mount Manual Call Point - Double Pole - Red

Zeta ZT-CP4F11 CP4 Conventional Flush Mount Manual Call Point - Double Pole - RedA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesFlush mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour RedDouble pole

GBP 16.15
1

Zeta ZT-CP4F11G CP4 Conventional Flush Mount Manual Call Point - Double Pole - Green

Zeta ZT-CP4F11G CP4 Conventional Flush Mount Manual Call Point - Double Pole - Green

Zeta ZT-CP4F11G CP4 Conventional Flush Mount Manual Call Point - Double Pole - GreenA CP4 Indoor Call Point. When the resettable element is pressed the spring mechanism mimics the feel of a break glass and the resettable element goes back.A completely new action system performs well and guarantees alarm detection in every condition.A reflective polyester flag appears at the bottom of the operating face providing the highest levels of visibility for the user. At the heart of the call point a spring-free mechanism is used to operate the flag and the switch via a patented design. This allows for long life and trouble-free operation.Key FeaturesFlush mountEN54-11 approvedVery high visibility of the alarm conditionNew efficient and reliable mechanismHigh impact resistant ABS glass fibre material - fully patentedQuick and easy installationColour GreenDouble pole

GBP 16.15
1

Hawco 312-300 12quot 14 NPT Female Hexagonal Retaining Nut for Detect-A-Fire Heat Detectors Pack of 6

Hawco 312-300 12quot 14 NPT Female Hexagonal Retaining Nut for Detect-A-Fire Heat Detectors Pack of 6

Pleasenote This product incurs additional shipping charges.Hawco 312-300 12 14 NPT Female Hexagonal RetainingNut for Detect-A-Fire Heat Detectors Pack of 6DETECT-A-FIRE D-A-F detectors are the heartof many fire protection systems. The highly reliable D-A-F has been thestandard for over 75 years. The D-A-F is used for signaling overheat or fireconditions. In most applications the D-A-F provides the initial heat sensingthat is used to activate suppression systems using clean agent CO2 inertgases wet or dry chemicals or water.D-A-F detectors are widely accepted because they aredesigned with rate compensation. This provides a unique advantage over bothfixed temperature and rate-of-rise types of detectors because the D-A-Fdetector accurately senses the surrounding air temperature regardless of thefire growth rate. At the pre-determined set point the system is activated.Fixed temperature detectors must be completely heated to alarm temperature andtherefore a lag in response time may occur with a fast rate fire. Rate-of-risedevices on the other hand are triggered by the rate of increase in ambienttemperature and are subject to false alarms caused by harmless transientthermal gradients such as the rush of warm air from process ovens. The key to the detectors sensitivity is in the design. Theouter shell is made of a rapidly expanding alloy which closely follows changesin surrounding air temperature. The inner struts are made of a slower expandingalloy. Designed to resist thermal energy absorption and sealed inside theshell the struts follow temperature changes more slowly. A slow rate fire willheat the shell and struts together. At the set point the detectorwill trigger actuating the alarm or releasing the extinguishant.A transient rush of warm air up to 40Fmin. mayexpand the shell while not triggering the detector. By ignoring transient warmair excursions the D-A-F detector virtually eliminates false alarms prevalentwith rate-of-rise devices. If a fast rate fire starts the shell will expandrapidly. The struts will close actuating the alarm andor releasing the agent.The faster the fire rate of growth the sooner the D-A-F detector will react.

GBP 11.74
1

Apollo Soteria Dimension Mounting Box FL5000-200APO

Apollo Soteria Dimension Mounting Box FL5000-200APO

Apollo Soteria Dimension Mounting Box FL5000-200APOThe Soteria Dimension Mounting Box is moulded from white flame-retardant polycarbonate. Positions for either side or top cable entry are marked on the outside of the Mounting Box to ensure correct cable positioning.An arrow has been placed on the rim to assist in correct orientation of the detector Placing the Mounting Box in the correct orientation in the installation aperture it is secured into position by screwing down the self-aligning fixing tabs. The Soteria Dimension Mounting Box is designed to be used with Soteria Dimension Optical Detectors.

GBP 12.47
1

Fireclass 517.050.023FC 5BEX 5 Universal Ex Detector Base

Fireclass 517.050.023FC 5BEX 5 Universal Ex Detector Base

Fireclass 517.050.023FC 5BEX 5 Universal Ex Detector BaseThe 517.050.023FC 5BEX detector base has been ATEX approved for use with the series M600Ex and series 800Ex intrinsically safe detectors and is covered by type examination certificates BAS01ATEX1134X3 and BAS01ATEX1194X3 respectively.The 5BEx 5 Universal Base is compatible with M600Ex MX 800Ex and the 800Exn ranges of Detectors. This document describes its use with the 800Exn series of detectors. Thus a ceiling-mounted detector comprises the specific detector type plus a 5BEx 5 Universal Base. The range is intended for two wire operation.When the detector is mounted on the base the detector LED provides a visual indication of its status through 360 degrees. The detector may be locked in position by inserting a locking key which is part of the detector moulding. This is broken from the sprue and inserted in the locking key slot.Key FeaturesHigh performanceDetector base is made of fire resistant FR110 BAYBLENDThe base can be used with the DHM-5BThe base accepts an address label carrier from the detector when it is fitted to the base. The base also has four electrical contacts which align with the contacts on the detector once the latter is fitted and fully latched into positionThe raised rib is aligned with a raised rib on the detector when the detector is in the fully home positionLoop cabling is connected to base terminals L -ve and L1 veA drive is provided for a remote indicator connected between loop positive and terminal RTerminal L2 is not used

GBP 14.99
1