20 results (0,14129 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

C-Tec CFP EN54-13 Sounder Circuit Fault Monitoring Module BF355

C-Tec CFP EN54-13 Sounder Circuit Fault Monitoring Module BF355

C-Tec CFP EN54-13 Sounder Circuit Fault Monitoring Module BF355The BF355 has been designed for use in conjunction with the BF354 EN54-13 Interface Board.Key FeaturesBSI certified to EN54-13 Fire detection and fire alarm systems compatibility assessment of system componentsDetects resistances down to 10 ohmsOne required per BF354 interface board sounder circuitMeasures 50mm x 26mm x 5mm with 100mm tail can bebe fitted inside or alongside the last device on thesounder circuitTechnical SpecificationsApprovalscertifications Certified to EN54-13 by the BSI KM615562Protocolcompatibility Must be used in conjunction with our BF354 EN54-13 Interface BoardApplicationoperation Allows a BF354 sounder circuit to detect resistances down to 10 plus or minus 10Product dimensions mm 50mm W x 26mm H x 5mm D with 100mm tails

GBP 25.42
1

Advanced MXP-505 Sounder Active EOL EN54-13

Advanced MXP-505 Sounder Active EOL EN54-13

Advanced MXP-505 Sounder Active EOL EN54-13The Sounder Active EOLperipheral is a sounder circuit active EOL Device. Sounder circuits can be configured for compliance with EN54-13 by programming the use of this peripheral. In order to comply with EN54-13 all panel sounder outputs must be fitted with the Sounder Active EOL.The Sounder Active EOLis a small and compact active end of line unit designed for termination and housing in third party sounder output devices.EN54-13 ComplianceIn order to comply with EN54-13 The MxPro 5system must check and warn prior to an alarm condition if the voltage at the last device cannot be maintained under the applied alarm load conditions. In order to meet this requirement the Sounder Active EOLactive EOL is required for all panel sounder outputs.By using this device third party accreditation assures compatibility as all components are individually tested and certified to the relevant harmonised product standard. This ensures that the system will fully operate as intended when actually needed.Key Features For use with EN54-13 ComplianceSupports device removalSimple to installSmall and compactFor use with all MxPro 5 series control panels

GBP 21.35
1

C-Tec NCP-13 Wipe Clean Anti-Bacterial Ceiling Pull Cord Pack

C-Tec NCP-13 Wipe Clean Anti-Bacterial Ceiling Pull Cord Pack

C-Tec NCP-13 Wipe Clean Anti-Bacterial Ceiling Pull Cord PackA BS8300 compliant anti-bacterial wipe-clean pull cord pack suitable for use with C-TECs Quantec and 800 Series ceiling pull units. Contains 3m of red vinyl encapsulated cord two triangular bangles and a red fixing bullet.Key FeaturesCord has integral properties that can help prevent the spread of infections such as MRSA e.coli c.diff S Aureus and the NorovirusIdeal for use in hospitals nursing and care homes doctors surgeries clinics and any other area where infection control is imperativeA simple and cost-effective means of updating existing ceiling pulls to comply with the stringent hygiene regulations of many health authorities and inspection bodiesEasy to clean using a clean cloth and mild detergentAlso compatible with many other manufacturers ceiling pull units

GBP 18.97
1

KAC M4A-G000SF-K013-13 Green Double Pole Surface Flexible Element Indoor Manual Call Point - Double Pole - Running Man Graphic Marking

KAC M4A-G000SF-K013-13 Green Double Pole Surface Flexible Element Indoor Manual Call Point - Double Pole - Running Man Graphic Marking

KAC M4A-G000SF-K013-13 Green Double Pole Surface Flexible Element Indoor Manual Call Point - Double Pole - Running Man Graphic MarkingInstallation efficiency flexibility and full compliance with the latest standards are at the heart of the new MCP indoor call point range.Installation time and ultimately cost are of paramount importance to any fire or security installer. The MCP range directly reflects this need by providing a unique plug and play concept designed specifically to reduce installation time. All new MCP products utilise a special terminal block where all initial installation cabling is terminated. This terminal block is then simply connected to the back of the MCP. Simple but effective with no re-termination required and no time wasted.Through new standards and legislation both break glass and resettable operating elements can now be used within a manual call point. To provide you with the greatest flex-ability the new MCP range can be configured as either a break glass or resettable unit by simply changing from one element to another. No other additional parts or alternative products need to be ordered.All MCP indoor call point products also help preserve the integrity of the overall system as illegal removal of the product lid will result in the call point operating and the system going into alarm.Full compliance with the latest standards is essential and the new MCP indoor call point range is fully approved to the latest EN54-11 standard compliant markings only.The MCP4A product version is supplied with a double pole changeover set of contacts. The product utilises two terminal blocks and wiring to the relevant terminals on these terminal connector blocks provides either a normally open or normally closed operation.Key FeaturesUnique Plug Play installation conceptTotal Flex-Ability in the choice of operating elementAnti-Tamper facilityEnhanced aestheticsFully approved to the latest standardsBackward compatibilityCPD Approved

GBP 27.73
1

Advanced MXP-501 Remote Battery Temperature Sensor for Advanced MxPro 5

Advanced MXP-501 Remote Battery Temperature Sensor for Advanced MxPro 5

Advanced MXP-501 Remote Battery Temperature Sensor for Advanced MxPro 5The Active EOL Battery Monitoringperipheral is a remote battery temperature device which should be used when charging batteries housed in large or external enclosures.EN54-13 ComplianceIn order to comply with EN54-13 The MxPro 5 system must check and warn prior to an alarm condition if the voltage at the last device cannot be maintained under the applied alarm load conditions. In order to meet this requirement the MxPro 5 active EOL is required for all panel sounder outputs.By using this device third party accreditation assures compatibility as all components are individually tested and certified to the relevant harmonised product standard. This ensures that the system will fully operate as intended when actually needed.Key FeaturesSimple to installExternal battery monitoringFor use with all MxPro 5 series control panels.Compatible with all MxPro 5 series control panels. The Active EOL Battery Monitoringcable length must not exceed500mm.DetailsModel MXP-501Shipping Weight 200g

GBP 42.68
1

NC-DPO-W Conventional Point Detector - Optical White

NC-DPO-W Conventional Point Detector - Optical White

NC-DPO-W Conventional Point Detector - Optical WhiteThe DC-9102E is a photoelectric optical detector suitable for use in hotels restaurants office buildings schools banks warehouses libraries computer rooms switch rooms etc.ApplicationThedetector supports installation on the GST DB-01 conventional detector base forstandard applications or the GST DB-01D diode base when head-out functionalityto BS5839 standard is required. Detection sensitivities are programmable usingthe GST P-9910B device programmer.Key FeaturesSupports drift compensation to enable good environmentaladaptabilitySelf-diagnosticLocal test activation with reed switchChamber contamination checkingAll round LED visibility 360 viewing angle avoids timespent on specific detector orientationConfigurable polling LED supportRemote indicator outputRemovable sensing chamber for easy maintenance2 Programmable smoke sensitivity levels

GBP 19.96
1

KAC K1020R Keyguard with Switch English

KAC K1020R Keyguard with Switch English

KAC K1020R Keyguard with Switch EnglishThe K1020R Red Keyguard box is fitted with a single pole changeover contact microswitch for connection the third party equipment CCTV intruder alarms etc.Designed to store escape route keys to keep them secure safe and accessible. The cover lens at the front is easy to remove from the unit removing the need of a hammer.The keyguard plastic window is designed in such a way that it cannot be refitted after removal and leaves no shards of glass or sharp edges that could cause injury enabling it to be used in such areas as schools food preparation areas and swimming pools.The keyguard is able to take both keys and access fobscards.Key Features3rd party connection for remote indicationCan be wired into existing alarm systemsSnatch off plastic windows availablePlastic window makes the Keyguard the ideal choice for food preparation areas schools and swimming poolsNo shards of glass or sharp edges that could cause injuryWidely used by fire exit doors in computer rooms for master key storage and other situations where a key or card needs to be kept safe and secure

GBP 39.84
1

C-Tec CA431AW CA Base Sounder White

C-Tec CA431AW CA Base Sounder White

C-Tec CA431AW CA Base Sounder WhiteCAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million-pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key Features255 devices per loopAutonomous decision-making for faster response timesMultiple type codes40V loop drive voltageTwo soft addressing options automatic via the panel ormanual via a powerful handheld programmerPowerful multi-level addressing facilitates easy device additionand swapped device identificationVolumes tones detector modes can be changed atcompatible panelsHigh-speed data transmission and robust data transferIntrinsically EN54-13 compliantProvides geographical location of short and open circuitfaults a short circuit isolator is included as standard in every CAST fielddeviceReplace device functionFuture seamless integration with other CAST life safetysystems reducing energy servicing installation and repair costsDesigned and manufactured in the UK

GBP 24.83
1

C-Tec CA432AW CA O Class Base Sounder VAD - White

C-Tec CA432AW CA O Class Base Sounder VAD - White

C-Tec CA432AW CA O Class Base Sounder VAD - WhiteCAST is the worlds most-advanced distributedintelligence fire alarm system protocol. Conceived designed and realised byC-TEC as part of a five-year multi-million-pound project it involved thecreation of a powerful proprietary communication protocol C-TEC AddressableSystem Technology CAST and multiple control panels field devices.Key Features255 devices per loopAutonomous decision-making for faster response timesMultiple type codes40V loop drive voltageTwo soft addressing options automatic via the panel ormanual via a powerful handheld programmerPowerful multi-level addressing facilitates easy device additionand swapped device identificationVolumes tones detector modes can be changed atcompatible panelsHigh-speed data transmission and robust data transferIntrinsically EN54-13 compliantProvides geographical location of short and open circuitfaults a short circuit isolator is included as standard in every CAST fielddeviceReplace device functionFuture seamless integration with other CAST life safetysystems reducing energy servicing installation and repair costsDesigned and manufactured in the UK

GBP 43.46
1

Gent VIG-BNG-DINKIT Bacnet Gateway Din Rail Mounting Kit for Mains Powered Interfaces S4-34440212

Gent VIG-BNG-DINKIT Bacnet Gateway Din Rail Mounting Kit for Mains Powered Interfaces S4-34440212

Gent VIG-BNG-DINKIT Bacnet Gateway Din Rail Mounting Kit for Mains Powered Interfaces S4-34440212The BACNET-GW-3 provides an interface between NOTIFIERs fire panel network either the standard or the high-speed version and a network using the BACnetIP communication protocol.BACnet protocol is an American National Standard ANSIASHRAE 135-1995. With the Gateway inter- face devices on NFN fire alarm control panels are represented as BACnet objects to the BACnet client.The user subscribes to Event Notification objects per FACP and the BACnet device receives events from objects on the FACP as a result of this subscription.The BACNET-GW-3 can be connected to a stand-alone ONYX panel 9th edition with an available network port or it can be connected to via the network port on any net- work control module.Connected to each BAC- NET-GW-3 can support a maximum of 14 other nodes or 15000 objects. Multiple BACNET-GW-3s can be used to interface with larger networksThe Vigilon BACnet Gateway VIG-BNG provides an interface between a computer network and GENT EN54 Vigilon fire detection and alarm system using BACnet communication protocol.

GBP 37.37
1

KAC K1020G Green Keyguard with Switch English

KAC K1020G Green Keyguard with Switch English

KAC K1020G Green Keyguard with Switch EnglishThe K1020G Green Keyguard box is fitted with a single pole changeover contact microswitch for connection the third party equipment CCTV intruder alarms etc.Designed to store escape route keys to keep them secure safe and accessible. The cover lens at the front is easy to remove from the unit removing the need of a hammer.The keyguard plastic window is designed in such a way that it cannot be refitted after removal and leaves no shards of glass or sharp edges that could cause injury enabling it to be used in such areas as schools food preparation areas and swimming pools.The keyguard is able to take both keys and access fobscards.Key Features3rd party connection for remote indicationCan be wired into existing alarm systemsSnatch off plastic windows availablePlastic window makes the Keyguard the ideal choice for food preparation areas schools and swimming poolsNo shards of glass or sharp edges that could cause injuryWidely used by fire exit doors in computer rooms for master key storage and other situations where a key or card needs to be kept safe and secure

GBP 39.84
1

Carbon Dioxide Extinguisher 2Kg - 2CX

Carbon Dioxide Extinguisher 2Kg - 2CX

Carbon Dioxide Extinguisher 2Kg - 2CXOur CO2 fire extinguishers are highly effective at tackling fires fuelled by flammable liquids and electrical equipment this makes Carbon Dioxide fire extinguishers perfect for situating in offices. CO2 fire extinguishers are usually just one half of an extinguisher team often being paired with either a water or foam extinguisher.All of our CO2 extinguishers are supplied with a frost free horn or Hose and horn 5kg to eliminate frost burn when using the extinguisher. By using aluminium to manufacture the main body our CO2 fire extinguishers are lightweight and easy to handle unlike steel body alternatives. These extinguishers are supplied with wall mounting brackets which make storing the unit easy and safe.Carbon Dioxide extinguishers are mainly used to cover electrical risks and also can extinguish smaller flammable liquid fires. The gas is clean and common places for use include computer server rooms and offices.Jewel Fire Group Carbon Dioxide extinguishers are assembled in the UK and we supply the 2Kg with a frost-free safe horn and the 5Kg with hose and horn as standard.Key Features10 year warranty from date of manufactureAluminium cylinders lighter than steel equivalent and lower risk of corrosion2Kg and 5Kg versions Marine Equipment Directive Approved recycling capabilityBoxed for safe transportationRecycling Capability

GBP 41.09
1

C-Tec BF440CF1 FUL Solista LX 24V Wall VAD Red Body - Red Flash Shallow Base

C-Tec BF440CF1 FUL Solista LX 24V Wall VAD Red Body - Red Flash Shallow Base

C-Tec BF440CF1 FUL Solista LX 24V Wall VAD Red Body - Red Flash Shallow BaseThe Solista LX visual alarm device VAD is an EN54-23 rated fire alarm beacon. Achieved through its unique lens design which distributes light in a highly controlled pattern it achieves the required illumination specific by EN54-23 while drawing a low current consumption.Taking its design principles from the popular Solista Maxi the Solista LX is compact and slim blending in when its not required and standing out when it is. Now in its second generation it features soft-start technology enabling the maximum product loading and protection against overloading and fault.The patented long life LED lens optics used in the LX have been developed specifically for the VAD EN54-23 standard.It uses modern thick-mould injection moulding techniques and innovative cylindrical output to achieve the correct level of illumination while keeping power consumption as low as possible.The 2nd generation of the LX now incorporates soft-start technology. This innovative feature constantly monitors the available voltage to give zero start up surge on the line allowing maximum product loading. It can also detect line overloading and will indicate the fault with a rapid double flash.Key FeaturesCertified to EN54 Parts 23 AFNOR and 13 BSIProvides W-2.4-7.5 coverage switchable to W-2.4-2.5 if required10-25mA alarm current depending on settingAttractive slim designUltra-bright red LEDIdeal for use in bedrooms bathrooms and toilets

GBP 36.13
1