44 results (0,15599 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Fireclass 514.800.806FC FC421CP-I Outdoor Call Point with Isolator

Fireclass 514.800.806FC FC421CP-I Outdoor Call Point with Isolator

Fireclass 514.800.806FC FC421CP-I Outdoor Call Point with IsolatorA comprehensive range of call points for use with FireClass addressable systems using the robust and reliable FireClass open protocol. All the call points are designed to enable an alarm signal to be given by a plastic resettable element which means that the call point can be easily reset after it has been activated. Any change in the status of the switch is immediately communicated to the FireClass Control and Indicating Equipment CIE. All call points have an integral short-circuit isolator for monitoring the addressable loop wiring.The integral LED indicator is normally off. When the frangible element is broken an alarm is registered and the LED will illuminate red. If a section of the loop wiring adjacent to the call point is shorted the built-in short-circuit isolator trips isolating the shorted section and the LED is illuminated yellow. The status remains until the short is removed. If required an optional transparent hinged cover may be installed to guard against accidental operation. Both indoor and outdoor versions are available.FC421CP-I Addressable Break Glass Call Point is designed to monitor and signal the condition of a switch contact that is operated by activating the deformable plastic element. The FC421CP-I is fitted into a standard weatherproof call point housing. IP67 protection degree.Key FeaturesIntegral short circuit isolatorDual colour LED indicationEN54-11 certificationCompact modern stylingTest key for fast testingIP67 ingress protection models for external applications

GBP 175.49
1

Apollo 29600-446 Intrinsically Safe Sounder Visual Indicator

Apollo 29600-446 Intrinsically Safe Sounder Visual Indicator

Apollo 29600-446 Intrinsically Safe Sounder Visual IndicatorThe I.S. Conventional Sounder and Conventional Sounder Visual Indicator are suitable for intrinsically safe signalling applications including fire security and process control. The Conventional I.S. Sounder is also available for Group I mining.Key FeaturesATEX certifiedIECEx certifiedGOST-R certified for Zone 0 applicationsFM certified for Class I Division 1 and Class I Zone 0 applications

GBP 413.62
1

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-R

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-R

Vimpex Intrinsically Safe Sounder Minialarm in Red IS-MA1M-RThe IS-mA1 is a compact 100dBA alarm sounder. Approvals include ATEX IECEx and GOST-R for Zone 0 applications and FM approval for Class I Division 1 and Class I Zone 0 applications.It is suitable for all intrinsically safe signalling applications including fire security and process control.Key FeaturesInput overload and reverse current protectionEnd of line resistor certifiedAuto synchronised sound outputAvailable with custom tone configurationsGroup1 Mining

GBP 238.09
1

Nittan Intrinsically Safe Beacon IS-MB1-R-R

Nittan Intrinsically Safe Beacon IS-MB1-R-R

Nittan Intrinsically Safe Beacon IS-MB1-R-RThe IS-mB1 is a compact beacon with an array of six high output L.E.Ds. Approvals include ATEX IECEx and EAC Ex for Zone 0 applications and FM approval for Class I Division 1 and Class I Zone 0 applications. The IS-mB1 is suitable for all intrinsically safe signalling applications including fire security and process control.Key FeaturesInput overload and reverse current protectionEnd of line resistor certifiedPrismatic lens optimises L.E.D effectiveness

GBP 313.56
1

Vimpex Intrinsically Safe Sounder Red IS-A105N-R

Vimpex Intrinsically Safe Sounder Red IS-A105N-R

Vimpex Intrinsically Safe Sounder Red IS-A105N-RThe IS-A105N is suitable for all intrinsically safe signalling applications including fire security and process control. The IS-A105N is a high output 105dBA alarm sounder. Approvals include ATEX IECEx and GOST-R for Zone 0 applications and FM approval for Class I Division 1 and Class I Zone 0 applications.Key FeaturesInput overload and reverse current protectionAuto synchronised sound outputUnit can be mounted using external lugs or internal BESA compatible fixing positions.Duplicate cable terminations in out for daisy-chain installations.Available with custom tone configurations and frequencies.

GBP 328.94
1

Ziton ACA-BI20-100 Bracket quotIquot - 200mm 7.9quot Zintec cw Silicon sleeve - Pack of 100

Ziton ACA-BI20-100 Bracket quotIquot - 200mm 7.9quot Zintec cw Silicon sleeve - Pack of 100

Ziton ACA-BI20-100 Bracket I - 200mm 7.9 Zintec cw Silicon sleeve - Pack of 100The ACA-BI series I-brackets extension pieces is designed to extend the positioning of linear heat cable installed on 7-brackets and edge clips. A silicon protection sleeve is supplied with the unit to protect the sensor cable when fastened to the bracket.The ACA-BI may be fitted to the bracket or clip and secured in place using a suitable bolt and nut at one end. The hole at the other end of the bracket allows for the securing of the sensor cable using a silicone sleeve and cable tie. The extension piece allows support for the sensor cable an additional approx. 200mm away from the end of the bracket or clip.Recommended spacing 1mKey FeaturesEasy installation of linear heat cableFor use on existing brackets and clips

GBP 370.62
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Red Lens IS-SB-02-02This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 212.14
1

Klaxon TCC-0002 Ex IS Beacon 24vDc Amber Lens

Klaxon TCC-0002 Ex IS Beacon 24vDc Amber Lens

Klaxon TCC-0002 Ex IS Beacon 24vDc Amber LensThis LED beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly On signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatible

GBP 187.96
1

Klaxon TCC-0005 Ex IS Beacon 24vDc Green with Clear Lens

Klaxon TCC-0005 Ex IS Beacon 24vDc Green with Clear Lens

Klaxon TCC-0005 Ex IS Beacon 24vDc Green with Clear LensThis LED beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly On signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatible

GBP 187.96
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with Amber Lens IS-SB-02-01This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. Further details can be found on the installation sheet This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 212.14
1

Klaxon TCC-0003 Ex IS Beacon 24vDc Red Lens

Klaxon TCC-0003 Ex IS Beacon 24vDc Red Lens

Klaxon TCC-0003 Ex IS Beacon 24vDc Red LensThis LED beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly On signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatible

GBP 187.96
1

Klaxon TCC-0006 Ex IS Beacon 24vDc White with Clear Lens

Klaxon TCC-0006 Ex IS Beacon 24vDc White with Clear Lens

Klaxon TCC-0006 Ex IS Beacon 24vDc White with Clear LensThis LED beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly On signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatible

GBP 187.96
1

Klaxon TCC-0004 Ex IS Beacon 24vDc Blue with Clear Lens

Klaxon TCC-0004 Ex IS Beacon 24vDc Blue with Clear Lens

Klaxon TCC-0004 Ex IS Beacon 24vDc Blue with Clear LensThis LED beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly On signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatible

GBP 187.96
1

Klaxon TCC-0011 Ex IS SounderBeacon 24vDc White With Clear Lens

Klaxon TCC-0011 Ex IS SounderBeacon 24vDc White With Clear Lens

Klaxon TCC-0011 Ex IS SounderBeacon 24vDc White With Clear LensThe IS Sonos sounder beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The sounder beacon unit incorporates a two stage alarm option and has a total of 32 selectable tones selectable via a dip switch on the PCB and produces up to 105dB at 1 Meter. A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleDustproof Weatherproof

GBP 232.19
1

Klaxon TCC-0008 Sonos IS SounderBeacon 24vDc Red Lens

Klaxon TCC-0008 Sonos IS SounderBeacon 24vDc Red Lens

Klaxon TCC-0008 Sonos IS SounderBeacon 24vDc Red LensThe IS Sonos sounder beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The sounder beacon unit incorporates a two stage alarm option and has a total of 32 selectable tones selectable via a dip switch on the PCB and produces up to 105dB at 1 Meter.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 232.19
1

Klaxon TCC-0009 Sonos IS SounderBeacon 24vDc Blue with Clear Lens

Klaxon TCC-0009 Sonos IS SounderBeacon 24vDc Blue with Clear Lens

Klaxon TCC-0009 Sonos IS SounderBeacon 24vDc Blue with Clear LensThe IS Sonos sounder beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The sounder beacon unit incorporates a two stage alarm option and has a total of 32 selectable tones selectable via a dip switch on the PCB and produces up to 105dB at 1 Meter.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 232.19
1

Klaxon TCC-0010 Ex IS SounderBeacon 24vDc Green With Clear Lens

Klaxon TCC-0010 Ex IS SounderBeacon 24vDc Green With Clear Lens

Klaxon TCC-0010 Ex IS SounderBeacon 24vDc Green With Clear LensThe IS Sonos sounder beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The sounder beacon unit incorporates a two stage alarm option and has a total of 32 selectable tones selectable via a dip switch on the PCB and produces up to 105dB at 1 Meter. A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleDustproof Weatherproof

GBP 232.19
1

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with White Lens IS-SB-02-05

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with White Lens IS-SB-02-05

C-Tec Moflash EX Intrinsically Safe Sounder Beacon with White Lens IS-SB-02-05This LED Beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.This range is suitable for Fire Security Process Control and general signalling applications. The beacon has a DIP switch that gives the options to change from a 1 Hz 60FPM flash rate to a static constantly on signal.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit. Connections are made to the base during the initial wiring phase which results in a faster more reliable installation.The beacon head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections. This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I Ma fGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T850 C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof WeatherproofPlease note The blue green and white versions are all fitted with clear lenses and it is the internal LEDs which then give the colour when operated.

GBP 222.01
1

Klaxon TCC-0007 Sonos IS SounderBeacon 24vDc Amber Lens

Klaxon TCC-0007 Sonos IS SounderBeacon 24vDc Amber Lens

Klaxon TCC-0007 Sonos IS SounderBeacon 24vDc Amber LensThe IS Sonos sounder beacon has been approved for use in potentially explosive atmospheres for Group I Mining Group II Above Ground applications and incorporates a high Ingress Protected IP66 enclosure.The sounder beacon unit incorporates a two stage alarm option and has a total of 32 selectable tones selectable via a dip switch on the PCB and produces up to 105dB at 1 Meter.A specially designed time saver base enables quick and easy installation of this unit with no extra cabling to be made to the head of the unit.Connections are made to the base during the initial wiring phase which results in a faster more reliable installation. The sounder head simply twists clicks into the pre-fixed base on commissioning avoiding any additional wiring connections.This unit must be used in conjunction with an approved Zener Barrier or Galvanic Isolator. The characteristics should not exceed Uo 28v Io 93mA Po 660mW Ci 0 Li 0. The minimum value of Uo should not drop below 23.6v and the minimum value of Io should not drop below 50mA.Key FeaturesApproved by ATEX IECExGroup I MI Ex ia I MaGroup II IGD Ex ia IIC T6 Ga Ex ia IIIC T85C DaZones 0 1 2 20 21 22Conforms to EN 60079-02012 All2013 IEC 60079-02011 EN-60079-112012 IEC 60079-112011Diode Polarised End of line resistor compatibleWhite base version available MOQ applyDustproof Weatherproof

GBP 232.19
1