4 results (0,12537 seconds)

Show all filters

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Cooper Fulleon 2450-NM Liquid det. Wh IP65 Corrosive Proof

Cooper Fulleon 2450-NM Liquid det. Wh IP65 Corrosive Proof

Cooper Fulleon 2450-NM Liquid det. Wh IP65 Corrosive ProofSensor that detects the presence of water on the floor by means of 2 golden feet.It is generally used for protection against flooding of data centres technical rooms boiler rooms offices laboratories etc.The sensor in an aluminium container with white epoxy paint is equipped with a steel support that allows to detect the liquid at a variable height between 0 and 11 mm as needed.In the event of an alarm the relay changes state and the built-in signalling LED lights up.Remote test and remote inhibition functions.The sensor circuit is oscillating to prevent electrolysis and corrosion problems.Connections with 7 wire terminals for code 2450-N and terminal connections for code 2450-NM 2 terminals for power supply 3 terminals for relay output in exchange 1 terminal for remote test 1 terminal for inhibition.Code 2450-N offers an IP 67 degree of protection thanks to the total encapsulation in epoxy resin.Alarm threshold adjustment with trimmer for code 2450-NM.Cannot be used with flammable liquids.

GBP 63.19
1

Carrier W867 UVIR Test Torch X-Flame Detector - Range UltravioletInfrared UVIR Test Lamp

Carrier W867 UVIR Test Torch X-Flame Detector - Range UltravioletInfrared UVIR Test Lamp

Carrier W867 UVIR Test Torch X-Flame Detector - Range UltravioletInfrared UVIR Test LampThe W867 UltravioletInfrared UVIR Test Lamp is a portable battery operated explosion-proof source of UV and IR radiation that is used for periodic testing of UV IR or UVIR flame detection systems.The W867 Test Lamp simulates a fire by producing UV and IR radiation with the same frequency and wavelength as the response range of Det-Tronics UVIR detectors enabling the operator to verify proper system operation without the need for an open flame.

GBP 13830.19
1

Carrier W6300B1003 DT Software and Connector X3301

Carrier W6300B1003 DT Software and Connector X3301

Carrier W6300B1003 DT Software and ConnectorDT Series Flame Detectors record pertinent configuration and event information in the devices non-volatile memory. Important detector status data such as power-updown faults and alarms are date and time stamped as they occur and stored in the electronic module located inside the detector enclosure. The Inspector Monitor software allows the user to later upload this data to a personal computer PC where it can be displayed saved andor printed. Enhanced Flame Inspector Software is compatible with all versions of X3301 X9800 and X5200 flame detectors.Key FeaturesData logging capability for Det-Tronics flame detectorsData stored in non-volatile memoryData can be uploaded to a PCData can be viewed stored to a file or printedPlease note This product has an alternative part code ofDet-tronics X3301

GBP 1046.83
1

Carrier X5200G DT Single-IR Hydrocarbon Complies with FM 3260 EN54 Certified

Carrier X5200G DT Single-IR Hydrocarbon Complies with FM 3260 EN54 Certified

Carrier X5200G DT Single-IR Hydrocarbon Complies with FM 3260 EN54 CertifiedThe X5200 UVIR Flame Detector meets the most stringent requirements worldwide with advanced detection capabilities and immunity to extraneous sources combined with a superior mechanical design. The mounting arrangement allows the UV and IR sensors to monitor the same hazardous location with a 90 degree cone of vision. When both sensors simultaneously detect the presence of a flame an alarm signal is generated. The detector has Division and Zone explosion-proof ratings and is suitable for use in indoor and outdoor applications.The standard output configuration includes fire fault and auxiliary relays. An optional 0 to 20 mA output with HART can be provided in addition to the three relays. A model with pulse output is available for easy retrofitting into existing Det-Tronics controller based systems. Auxiliary relay and 0 to 20 mA output are not available with the pulse model. A tri-color LED on the detector faceplate indicates normal condition and notifies personnel of fire alarm or fault conditions.The X5200M UVIR detector utilizes a molybdenum moly UV sensing element. Moly-based UV sensors have an increased spectral range of 1850 to 2650 angstroms which is better suited for detecting substances with unusual chemistry and some black powders.The X5200 housing is available in aluminium or stainless steel with NEMA 4X and IP66IP67 rating.Key FeaturesComplies with FM 3260EN54 certifiedCertified SIL 2 capableATEX Directive compliantEQP models availableA new level of false alarm rejectionResponds to a fire in the presence of modulated blackbody radiation i.e. heaters ovens turbines without false alarmHART models availableFDTDTM capableHigh speed capabilityMicroprocessor controlled heated optics for increased resistance to moisture and iceAutomatic manual or magnetic oi optical integrity testing no external test lamp requiredEasily replaceable oi plateFire fault and auxiliary relays standardMODBUS RS-485 communication0 to 20 mA isolated output optionalPulse output for compatibility with controller based systems optionalA tri-color LED on the detector faceplate indicates normal condition and notifies personnel of fire alarm or fault conditionsMounting arm allows easy sightingIntegral wiring compartment for ease of installationClass A wiring per NFPA-72Meets NFPA-33 response requirement for under 0.5 second available when model selectedRFI and EMC Directive compliantBuilt-in data logging event monitoring

GBP 6133.75
1