13.922 results (0,18062 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Show all

Reset filter

Products
From
Shops

Vimpex FC3ZEP Zone Extension PCB

Vimpex FC3ZEP Zone Extension PCB

Vimpex FC3ZEP Zone Extension PCBA zone extension PCB is also available to seamlessly add an additional 3 zones six sounder circuits. Each zone has two sounder circuits rated at 2 amps each. With the MMSP this provides up to 4 zones or 8 sounder circuits with a total load of 16 amps.When the ZEP is attached to the MMSP all messages whether fire or auxiliary are synchronised. Many MMSPs can be connected together to allow for synchronisation of the primary message across any number of zones. Each MMSP can support one Zone Extension PCB and any number of MMSPs can be connected together.If a zone goes to Fire it will change its message immediately or at the end of the current auxiliary message.If an additional zone goes to Fire then it will broadcast an alarm tone until it synchronises with the zone already in Fire.

GBP 227.80
1

Aritech ATS1202 Plug-in 8-zone Expander Card

Aritech ATS1202 Plug-in 8-zone Expander Card

Aritech ATS1202 Plug-in 8-zone Expander Card For ATS12011201E 1203 1203E 1204 1204E 1210L 1210LEInput expanders are devices for expanding the input capacity of an Axon Advisor Advance or a MASTER panel or a DGP. Depending on the basic capacity of the panel up to 3 x ATS1202 input expanders can be used. The unit easily can be daisy-chained.Expanding featuresA standard 8 zone DGP can have eight zones connected to it. This can be expanded in increments of 8 up to 32 using the ATS1202 8-Zone expanders A DGP can have 8 16 24 or 32 zones. A control panel can have 8 or 16 zones connected to it depending on control panel type. There are sixteen zones allocated to every DGP address. This can be incremented to a maximum of 32 zones by fitting ATS1202 expander modules. If a DGP has 24 or 32 zones two or three expanders fitted theadditional system zone numbers are taken from the following DGP address. If this is done the next DGP address ceases to exist and is not included to be polled e.g. DGP 1 has 24 zones zones 17 to 40. The next DGP in the system must now be addressed and polled as DGP 3 because zones 33 to 40 on DGP 1 have been taken from DGP 2.Key FeaturesExpandable to maximum 32 zonesDepending on DGP or Panel 2 or 3 expander modules can be fittedCompatible with Axon and Advisor Advanced panelsUnit can be daisy chained easily

GBP 52.62
1

Kidde Airsense EST-DMS Zone Microphone

Kidde Airsense EST-DMS Zone Microphone

Kidde Airsense EST-DMS Zone MicrophoneThis zone microphone is used to activate general public announcements to choose individual zones and to broadcast live voice messages. It can be connected directly to a selected Control Unit or via an additional Ethernet switch. A zone microphone can be powered locally 48 V or from a Control Unit via POE.It is equipped with programmable function keys which can be used to assign functions as required. All operational parameters can be programmed e.g. assignment of zones to various keys naming of zones and zone groups determining priorities setting up access rights to announcements volume controls push to talk key music onoff and music routing. Furthermore LEDs on the EST-DMS provide information about existing fault on the system any faults in a specific speaker zone evacuation mode on and type of announcement in the zone BGM PA EVAC Warning fireman microphone.Up to 5 EST-EKB-20M keyboard extensions with additional function keys can be attached to a zone microphone. Similarly to a fireman microphone it is also equipped with an intercom function and is able to communicate with other microphones in the system.Key FeaturesMonitored connection of the unit to the system9 fully-programmable keys with a possibility of connecting up to five20-key extensions4 non-symmetrical audio inputs 18 stereo jack connectorBuilt-in speakerStereo jack sockets for a headsetImplemented intercom functionPower supply via POE

GBP 866.45
1

Apollo Marine DIN-Rail Zone Monitor 55000-773MAR

Apollo Marine DIN-Rail Zone Monitor 55000-773MAR

Apollo Marine DIN-Rail Zone Monitor 55000-773MARThe Marine DINRail Zone Monitor powers and controls the operation of a zone of up to 20 conventional fire detectors from a loop of XP95 addressable detectors and ancillary devices.OperationThis unit needs to be installed in a suitable enclosure and secured using end stops part no 27447-528 or equivalent. The Marine DINRail zone monitor is factory pre-set to return an analogue value of 16 when all detectors on the zone are in the quiescent state and 64 when a detector changes to the alarm state.The unit latches in the alarm state. A 5.1K end-of-line resistor is used to monitor cables for open and short-circuit faults. Alternatively an active end-of-line monitor may be used in conjunction with diode bases and a capacitor of up to 50F fitted at the unit wiring terminals. In either case an analogue value of 4 is transmitted during open or short-circuit faults.The Marine DINRail zone monitor is fitted with a bi-directional short-circuit isolator and will be unaffected by loop short-circuits on either loop input or output.Key FeaturesLoop-poweredVisible short-circuitLED Built in isolator

GBP 112.91
1

Ziton ZP1-F4-MB ZP1 Main Board - 4 Zone Replacement Main PCB for the ZP1-F4-xx

Ziton ZP1-F4-MB ZP1 Main Board - 4 Zone Replacement Main PCB for the ZP1-F4-xx

Ziton ZP1-F4-MB ZP1 Main Board - 4 Zone Replacement Main PCB for the ZP1-F4-xxThe ZP1-F4-MB is a ZP1 Main Board - 4 Zone Replacement Main PCB designed for the ZP1-F4 range of panels.Key FeaturesMaximum system capacity device count Up to 1280Network size nodes Up to 16Maximum loop capacity 4Maximum zone capacity Up to 4Form factor SmallPhysical dimensions 163 x 60 x 245 mm W x H x DNet weight 245 gShipping weight 340 gMounting type In cabinet

GBP 205.84
1

Ampac 4310-0086 FireFinder Plus 32 Zone Alarm Indicator Module

Ampac 4310-0086 FireFinder Plus 32 Zone Alarm Indicator Module

Ampac 4310-0086 FireFinder Plus 32 Zone Alarm Indicator ModuleProvides 32 Zone LEDs capable of indicating Zone Fire Disable Fault and Dependency B conditions. The indicators may also be programmed to respond to the activation of Inputs or other panel actions other than Zone status.The 32 Zone Indication module incorporates customisable zone identification label inserts and is fully programmable viaConfigManagercause effect software application.

GBP 220.18
1