20 results (0,15899 seconds)

Brand

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Mitsubishi VL100EU5-E Lossnay Wall Mounted Single Room MVHR

Vent Matika EKA NV duct heater

Vent Matika EKA NV duct heater

Vent Matika EKA NV duct heater Description The Vent Matika EKA NV range of electric duct heaters are Used in ventilation systems as heaters for comfort, or preheaters, to protect the ventilation unit from frost. The EKA NV is controlled by a duct temperature sensor and unit mounted set point controller BPC Ventilation are the largest independent MVHR specialists and supply lifetime technical support on our top-quality systems, Key Features Controlled via unit mounted set point controller Internal temperature regulator May be used as a Pre Heater or a Post Heater Twin overheating protection Easy to use screw terminals Rubber sealed ductwork connections Can be installed both horizontally and vertically Stainless steel heating element Aluzinc Casing CE, RoSH & Reach certified Control Options The EKA NV unit uses a duct mounted temperature sensor and is controlled via the set point potentiometer on the top of the heater casing. Overheating Protection Two overheat protection thermostats are installed in the electrical circular heater EKA. The first one with automatic reset, turns off the heating when the temperature reaches 50 °C and turns on when the temperature drops below 50 °C. The second with manual safety reset, turns off the heating when the temperature reaches 100 °C. In this case you need to figure the cause of the overheating of the heater. Eliminate the overheating cause and press the RESET button on the heaters cover. Construction Manufactured of from Aluzinc coated steel which is high temperature proof Mounting Heaters can only be installed inside away from moisture and mounted horizontally with the electrical connection box facing upwards or sideways and vertically (only if the air flow direction upwards). Installation Temperature The maximum temperature of the output is 50 °C. Dimensions Models These models are kept in stock, but other sizes and power outputs are available to order and please contact our team for cost and availability 100mm - 0.6kw Electric Duct Heater - EKA-NV-100-0.6 125mm - 1.2kw Electric Duct Heater - EKA-NV-125-1.2 160mm - 1.2kw Electric Duct Heater - EKA-NV-160-1.2 160mm - 2.4kw Electric Duct Heater - EKA-NV-160-2.4 200mm - 3.0kw Electric Duct Heater - EKA-NV-200-3.0 250mm - 3.0kw Electric Duct Heater - EKA-NV-250-3.0 Optional accessories PTC Airflow sensor– Unit mounted sensor for electronic protection from insufficient airflow. The heater is only allowed to work if the airflow velocity is 1,5m/s or higher PS Differential Pressure Switch – a unit mounted pressure switch that provides mechanical protection against loss or insufficient airflow. The heater if not allowed to heat unless a minimum airflow of 1,5m/s is reached.   (Note -due to required velocity the PTC or PS option may not work on some smaller domestic MVHR or MEV systems with low airflow rates) PTC/PS – Sensor for minimum air velocity detection and diff. pressure switch for air flow detection PTC/K – Sensor for minimum air velocity detection and contactor for overheating protection 2NTC – 2 sensors for the air temperature measuring PTC/2NTC – Sensor for min. air velocity detection and 2 sensors for the air temperature measuring By ordering the PS, an internal contactor for power supply is added to the heater as well.   BPC Support We don’t sell boxes; we provide a service that few can match Free Lifetime Technical support on purchased items

GBP 291.68
1

DucoBox Silent UK MEV Unit with Humidity Sensor

DucoBox Silent UK MEV Unit with Humidity Sensor

Part no: 0000-4490 DucoBox Silent MEV Unit with Humidity Sensor The DucoBox silent Uk is a high quality MEV unit that extracts continually from the kitchen and bathrooms to one central unit to provides a quiet and efficient ventilation system Demand controlled with an internal humidity sensor that will automatically increase the speed to lower high humidity levels Manufactured in Belgium and developed with double wall construction to provide the quietist MEV available in Europe With a high performance of 400 m3/hr. this unit is ideally suited for high quality new builds or high-end renovations with up to 7 extract points The DucoBox silent has 7 x125mm connections and 1 x 125mm outlet With the optional Q-V adaptors this unit is also suitable with the use of up to 7 x 90mm crushproof radial ductwork connections with antibacterial lining that will lower the installation time and comply to the latest building control regulations BPC are MEV specialists and the original developers of MEV kits in the Uk and Ireland with lifetime technical support on our top-quality systems   Demand Controlled Ventilation Historically, MEV-units used to run continuously: 24 hours a day, 7 days a week. At a single set speed This was deemed to be “ok” so the energy losses were deemed to be small. DUCO feels that this “old school”-way-of-thinking is a thing of the past and decided to go a step beyond the “normal” operation mode of a “traditional” MEV system. DUCO offers true “on demand” solutions which result in true energetically optimised ventilation solutions: To only ventilate, when necessary, where it is necessary and as long as it is necessary! The DucoBox Silent has an internal humidity sensor that detects high humidity and increases the performance until the set level is reached again It is also possible to install a CO2 box sensor inside the DucoBox Silent UK With an “on demand” DUCO-system, the occupant can always be assured to breathe the best possible indoor air, whilst also using the least amount of energy! DUCO brings you the SMARTEST ventilation solutions! Silent Plus Kit The Silent Plus Kit provides additional acoustic damping of up to 3 dB(A)! The kit consists of three acoustic composite foam pads and three acoustic caps that are placed into the predesigned inserts inside the unit  Quiet-Vent adaptors The Quiet-Vent 125 to 90 adapters allow you to connect the 90mm radial pipe directly to the unit avoiding the use of a distribution box that will provide many benefits over using solid rigid ducting Up to 7 number 90mm radial ducts can be used on the unit This option will reduce installation time over solid rigid duct, reduce cost as there is no need for a distribution box, and comply with the latest building control requirements  Fault Indicator With the optional wall mounted fault indicator, you can be notified by colored indicator light when a fault is detected (max one per unit)  Boost switch A boost switch will allow the user to manually increase or decrease the speed, there is a manual 2 speed and 3 speed switches available Only one boost switch is recommended per unit and if the speed is set to high it will override any sensors and remain at that speed till manually reset to a lower speed A boost switch is required to commission the unit

GBP 345.20
1

Vent Matika EKA NI duct heater

Vent Matika EKA NI duct heater

Vent Matika EKA NI duct heater Description The Vent Matika EKA NI range of electric duct heaters are Used in ventilation systems as heaters for comfort, or preheaters, to protect the ventilation unit from frost. The EKA NI is controlled by a room mounted set point controller BPC Ventilation are the largest independent MVHR specialists and supply lifetime technical support on our top-quality systems, KEY FEATURES – Vent Matika NI heater Controlled via room mounted set point controller Internal temperature regulator May be used as a Pre Heater or a Post Heater Twin overheating protection Easy to use screw terminals Rubber sealed ductwork connections Can be installed both horizontally and vertically Stainless steel heating element Aluzinc Casing CE, RoSH & Reach certified CONTROL OPTIONS The EKA NV has a wall mounted setpoint controller connected to a duct mounted temperature sensor at the heater   When connected, the heater is working according to the duct sensor, and the supply air temperature sensor limits supply air temperature – +15°C…+40°C. Overheating Protection Two overheat protection thermostats are installed in the electrical circular heater EKA. The first one with automatic reset, turns off the heating when the temperature reaches 50 °C and turns on when the temperature drops below 50 °C. The second with manual safety reset, turns off the heating when the temperature reaches 100 °C. In this case you need to figure the cause of the overheating of the heater. Eliminate the overheating cause and press the RESET button on the heaters cover. Construction Manufactured of from Aluzinc coated steel which is high temperature proof Mounting Heaters can only be installed inside away from moisture and mounted horizontally with the electrical connection box facing upwards or sideways and vertically (only if the air flow direction upwards). Installation Models These models are kept in stock, but other sizes and power outputs are available to order and please contact our team for cost and availability 100mm - 0.6kw Electric Duct Heater - EKA-NI-100-0.6 125mm - 1.2kw Electric Duct Heater - EKA-NI-125-1.2 160mm - 1.2kw Electric Duct Heater - EKA-NI-160-1.2 160mm - 2.4kw Electric Duct Heater - EKA-NI-160-2.4 200mm - 3.0kw Electric Duct Heater - EKA-NI-200-3.0 250mm - 3.0kw Electric Duct Heater - EKA-NI-250-3.0 Optional accessories PTC Airflow sensor– Unit mounted sensor for electronic protection from insufficient airflow. The heater is only allowed to work if the airflow velocity is 1,5m/s or higher PS Differential Pressure Switch – a unit mounted pressure switch that provides mechanical protection against loss or insufficient airflow. The heater if not allowed to heat unless a minimum airflow of 1,5m/s is reached.   (Note -due to required velocity the PTC or PS option may not work on some smaller domestic MVHR or MEV systems with low airflow rates) PTC/PS – Sensor for minimum air velocity detection and diff. pressure switch for air flow detection PTC/K – Sensor for minimum air velocity detection and contactor for overheating protection 2NTC – 2 sensors for the air temperature measuring PTC/2NTC – Sensor for min. air velocity detection and 2 sensors for the air temperature measuring By ordering the PS, an internal contactor for power supply is added to the heater as well. BPC Support We don’t sell boxes; we provide a service that few can match Free

GBP 291.68
1

Vent Matika EKA NIS duct heater

Vent Matika EKA NIS duct heater

Vent Matika EKA NIS duct heater Description The Vent Matika EKA NIS range of electric duct heaters are Used in ventilation systems as heaters for comfort, or preheaters, to protect the ventilation unit from frost The Vent Matika EKA NIS range of electric duct heaters are controlled by an external 0 to 10v DC signal from a compatible MVHR unit or independent controller BPC Ventilation are the largest independent MVHR specialists and supply lifetime technical support on our top-quality systems, Key Features Controlled via a 0 to 10v DC signal Internal temperature regulator May be used as a Pre Heater or a Post Heater Twin overheating protection Easy to use screw terminals Rubber sealed ductwork connections Can be installed both horizontally and vertically Stainless steel heating element Aluzinc Casing CE, RoSH & Reach certified Control Options 0-10v sensor from a compatible MVHR unit or independent controller will allow 0-100% control of the heaters power Overheating Protection Two overheat protection thermostats are installed in the electrical circular heater EKA. The first one with automatic reset, turns off the heating when the temperature reaches 50 °C and turns on when the temperature drops below 50 °C. The second with manual safety reset, turns off the heating when the temperature reaches 100 °C. In this case you need to figure the cause of the overheating of the heater. Eliminate the overheating cause and press the RESET button on the heaters cover. Construction Manufactured of from Aluzinc coated steel which is high temperature proof Mounting Heaters can only be installed inside away from moisture and mounted horizontally with the electrical connection box facing upwards or sideways and vertically (only if the air flow direction upwards). Installation Temperature The maximum temperature of the output is 50 °C. Dimensions Models These models are kept in stock, but other sizes and power outputs are available to order and please contact our team for cost and availability 100mm - 0.6kw Electric Duct Heater - EKA-NIS 100-0.6 125mm - 1.2kw Electric Duct Heater - EKA-NIS-125-1.2 160mm - 1.2kw Electric Duct Heater - EKA-NIS-160-1.2 160mm - 2.4kw Electric Duct Heater - EKA-NIS-160-2.4 200mm - 3.0kw Electric Duct Heater - EKA-NIS-200-3.0 250mm - 3.0kw Electric Duct Heater - EKA-NIS-250-3.0 Optional accessories PTC Airflow sensor– Unit mounted sensor for electronic protection from insufficient airflow. The heater is only allowed to work if the airflow velocity is 1,5m/s or higher PS Differential Pressure Switch – a unit mounted pressure switch that provides mechanical protection against loss or insufficient airflow. The heater if not allowed to heat unless a minimum airflow of 1,5m/s is reached.   (Note -due to required velocity the PTC or PS option may not work on some smaller domestic MVHR or MEV systems with low airflow rates) PTC/PS – Sensor for minimum air velocity detection and diff. pressure switch for air flow detection PTC/K – Sensor for minimum air velocity detection and contactor for overheating protection 2NTC – 2 sensors for the air temperature measuring PTC/2NTC – Sensor for min. air velocity detection and 2 sensors for the air temperature measuring By ordering the PS, an internal contactor for power supply is added to the heater as well.  BPC Support We don’t sell boxes; we provide a service that few can match Free Lifetime Technical support on purchased items Largest independent MVHR suppliers Lowest cost on full systems guaranteed Inhouse design Team Inhouse certified training Largest range and stock available Worldwide delivery options

GBP 195.38
1

Vent Axia Lo-Carbon Multivent MVDC-MSH unit with Humidity Sensor

Vent Axia Lo-Carbon Multivent MVDC-MSH unit with Humidity Sensor

Vent Axia Lo-Carbon Multivent MVDC-MSH unit with Humidity Sensor Product Part Number Vent Axia MVDC-MSH - 443298 Key Features Internal Humidity sensor Ultra-quiet - acoustically lined for low noise levels Recognised in SAP Appendix Q Complies with Building ADF (System 3) Option of wall, ceiling, and loft mounting Improved controllability The unit has Long life, low energy multispeed DC motor Ceiling, wall, or floor Installation is recommended  PVC outer casing with an acoustic lining is included as standard, ensuring minimum noise levels. Technical Features Max Airflow of 350m3/h Best in class Specific Fan Power (SFP) as low as 0.15 wls Dimensions (mm) 330 long x 391 wide x 248 high Fitted with four extract 125 or 100mm diameter spigots allowing quick connection to ducts Switched Live Boost connection Fully variable normal and boost speeds Fully serviceable unit with all parts accessible 2-year standard or optional 5-year parts warranty Controllability The potentiometer-controlled speed selector allows accurate setting of airflow The unit has 2 fully variable speeds for trickle and boost, with an inbuilt humidistat activation for the boost speed. A switched live (LS) can also be used to select boost speed when wired through an Isolator Relay (Part No. 442030 - not supplied). An additional third speed (purge) is available using a second switched live connection. MVDC-MS H (443298) the Boost setting is activated by the internal humidity sensor. The internal humidity sensor uses one of the two available LS inputs, the other remaining LS input can be used to switch the unit to Purge speed.  MVDC-MS H has the option to switch from Normal to Boost speed (in effect over-riding the internal humidity sensor), this can be achieved by connecting an isolated switched live connection to the LS connection on the power supply terminal block. This must be isolated by using, for example an Isolator Relay Control, Vent-Axia part number 442030, or similar. Isolator relay controller, Vent-Axia part number 442030

GBP 204.00
1

Vent-Angel Ventilation Fire Safety Unit

Vent-Angel Ventilation Fire Safety Unit

Vent-Angel Ventilation Fire Safety Unit Product Part Number Vent-Angel Fire Safety Unit - QV-VA-21 Description The Vent-Angel is suitable for domestic homes and apartments and connects to any domestic fire alarm and will in the unfortunate event of a fire will remove the power supply to any type of Ventilation unit. The Vent-Angel unit can also control mains powered fire dampers, Purge fans or other devices The Vent -Angel is simple to install and comes complete with a discrete wall mounted control panel to test and reset the system. Why Use a Vent-Angel If a fire breaks out there is a possibility that any system that supplies fresh air could further cause the fire to intensify and spread. If even a small fire breaks out the smoke will enter the ventilation unit’s ductwork that could be very costly to remove any contaminants and smell. Control Panel The Vent-Angel includes a Test / Rest switch plate which would be mounted remotely in a location that has easy access (i.e. Hallway, Utility room), the switch plate also has LED operational indication. i.e. the Test push button with be illuminated Green under normal running conditions and the Reset push button will be illuminated Red in the event of a fault. The Test / Reset switch plate will also allow the system to be tested by pushing the TEST button. (It is recommended that this test is carried out twice yearly), to Reset the system press the RESET button, this action is also required if the system has been activated. Please ensure all Smoke/Fire Alarm issues have been resolved before activating the Vent Angel system. Contents: 1 x Vent Angel unit 1 x Vent Angel Test/Reset switch plate 1 x 15m length of 9 core YY cable 1 x 4mm O ring crimp 2 x Lockable Glands (FUW optional Fire Damper / Purge unit)

GBP 204.00
1

Domus CMX-S MEV Unit

Domus CMX-S MEV Unit

Domus CMX-S MEV Unit Product Part Number Domus CMX-S MEV unit - CMX-S Description Previously known as the Polypipe or Silavent Green Line CMX At just 125mm in depth, the CMX is one of the most versatile, easy to install and energy efficient MEV solutions available on the market. Ideal for installation in a wide range of properties, the CMX offers a depth of just 125mm, making it ideal for small ceiling voids or for where space is restricted. Fits into ceiling voids and utility cupboard spaces – horizontally or vertically The 220x90 duct connectors can be converted to 150 round using additional adaptors if required. Technical Features Max Airflow of 430m3/h Specific Fan Power (SFP) as low as 0.24 wls Dimensions (mm) 710 long x 340 wide x 125 high Fitted with two 220x90 duct connections allowing quick connection to ducts Suitable for a floor area up to 275m² The appliance has a low energy, high efficiency EC backward curved centrifugal impeller fan/motor assembly with sealed for life bearings suitable for +50ºC to -25 ºC. Also referred to as System 3 in Approved Document F of the Building Regulations, an MEV system consists of a centralised ventilation unit that continuously extracts waste, polluted and moist air from wet rooms and can be discreetly positioned in either a cupboard, utility room, ceiling or loft space. An MEV system can be ducted throughout the dwelling and operated by the homeowner through a range of control options. Controllability Typically dual speed, MEV systems provide both low speed continuous trickle ventilation and high-speed boost flow when required. Replacement fresh air is drawn into the dwelling through background ventilators i.e. air inlets, located in the living areas. The potentiometer-controlled speed selector allows accurate setting of 3 airflow speeds The unit has 3 fully variable speeds for trickle and boost,  A switched live (LS) can also be used to select boost speed  An additional third speed (purge) is available using a second switched live connection. Construction PVC outer casing with an acoustic lining is included as standard, ensuring minimum noise levels. Accessories ANC848A Manual LOW/BOOST switch Manual BOOST selection switch. LOW speed is engaged upon connection of mains supply. Both speeds are manually adjustable at the wiring centre to facilitate Building Regulation commissioning speeds. ANC849A Manual

GBP 386.03
1

DucoBox Connect MEV

DucoBox Connect MEV

DucoBox Connect MEV The DucoBox silent Connect is a high-quality demand controlled MEV unit that extracts continually from the kitchen and bathrooms to one central unit to provides a quiet and efficient ventilation system The difference between the DucoBox Silent Uk and DucoBox silent connect is that there is additional possibility to connect several additional features of Wall mounted Wired or RF Remote controls, Room sensors, Connectivity board allowing control via APP and the possible use of the optional commissioning App kit The unit does not come with any sensors and all options are at extra cost Demand controlled with optional internal humidity or Co2 box sensor that will automatically increase the speed to lower high humidity levels Manufactured in Belgium and developed with double wall construction to provide the quietist MEV available in Europe With a high performance of 400 m3/hr. this unit is ideally suited for high quality new builds or high-end renovations with up to 7 extract points The DucoBox silent has 7 x125mm connections and 1 x 125mm outlet With the optional Q-V adaptors this unit is also suitable with the use of up to 7 x 90mm crushproof radial ductwork connections with antibacterial lining that will lower the installation time and comply to the latest building control regulations BPC are MEV specialists and the original developers of MEV kits in the Uk and Ireland with lifetime technical support on our top-quality systems Key Features Suitable for up to 7 bathrooms Quietest MEV unit in Europe Powerful airflow rate of up to 400 m³/hour @ 150 Pa Sap Appendix Q (BRE) approved Low energy High performance DC fan SFP as low as 0.25 W.L.S. Optional C02 sensor Optional acoustic plus kit Only 4.3 kg in weight Slimline dimensions of 480x480x195mm 3 x Variable fan speeds 2+1 Year parts warranty* Optional 2 or 3 speed switch Suitable for wall or floor mounting Optional Humidity or CO2 box sensor Optional Wired / RF wall controller Optional App / BMS control Optional commissioning App kit Optional 7x 125 to 90 radial adaptors Optional fault indicator Optional laptop connection for commissioning Demand Controlled Ventilation Historically, MEV-units used to run continuously: 24 hours a day, 7 days a week. At a single set speed This was deemed to be “ok” so the energy losses were deemed to be small. DUCO feels that this “old school”-way-of-thinking is a thing of the past and decided to go a step beyond the “normal” operation mode of a “traditional” MEV system. DUCO offers true “on demand” solutions which result in true energetically optimised ventilation solutions: To only ventilate, when necessary, where it is necessary and as long as it is necessary! The DucoBox Silent has an internal humidity sensor that detects high humidity and increases the performance until the set level is reached again It is also possible to install a CO2 box sensor inside the DucoBox Silent UK With an “on demand” DUCO-system, the occupant can always be assured to breathe the best possible indoor air, whilst also using the least amount of energy! DUCO brings you the SMARTEST ventilation solutions!   External Control Components The DucoBox Silent Connect can be linked with the following external control components.   Box Sensors Box sensors can be installed very easily and quickly and provide CO2 and/or moisture measurement in an air duct. They are wired directly to the circuit board. This means that no wiring for room sensors need to be provided. A DucoBox Silent contains a maximum of two box sensors – one CO2 Box sensor and/or one Humidity Box Sensor – each of which can be clicked separately into a specific duct opening or together into one duct opening of the DucoBox. Smart Demand User controller There are 3 types of User controllers are available in either wireless or wired versions and in black or white face plates Remote control (popular option) Remote Control with CO2 sensor Remote control with Humidity Sensor The wired version will require the additional 24v Power supply Duco Connectivity Board The Duco Connectivity Board enables the Duco Installation App to be used on your phone or tablet This PCB also enables interfacing for home automation and building management systems via REST API (locally or via the cloud) or Modbus TCP (locally). Both possible via Ethernet and Wi-Fi. CO2 Room Sensors The CO2 Room sensor is available in either wireless or wired versions and with black or white face plates Switch

GBP 383.39
1

DucoBox Connect MEV with RH BOX Sensor

DucoBox Connect MEV with RH BOX Sensor

DucoBox Connect MEV The DucoBox silent Connect is a high-quality demand controlled MEV unit that extracts continually from the kitchen and bathrooms to one central unit to provides a quiet and efficient ventilation system The difference between the DucoBox Silent Uk and DucoBox silent connect is that there is additional possibility to connect several additional features of Wall mounted Wired or RF Remote controls, Room sensors, Connectivity board allowing control via APP and the possible use of the optional commissioning App kit The unit does not come with any sensors and all options are at extra cost Demand controlled with optional internal humidity or Co2 box sensor that will automatically increase the speed to lower high humidity levels Manufactured in Belgium and developed with double wall construction to provide the quietist MEV available in Europe With a high performance of 400 m3/hr. this unit is ideally suited for high quality new builds or high-end renovations with up to 7 extract points The DucoBox silent has 7 x125mm connections and 1 x 125mm outlet With the optional Q-V adaptors this unit is also suitable with the use of up to 7 x 90mm crushproof radial ductwork connections with antibacterial lining that will lower the installation time and comply to the latest building control regulations BPC are MEV specialists and the original developers of MEV kits in the Uk and Ireland with lifetime technical support on our top-quality systems Key Features Suitable for up to 7 bathrooms Quietest MEV unit in Europe Powerful airflow rate of up to 400 m³/hour @ 150 Pa Sap Appendix Q (BRE) approved Low energy High performance DC fan SFP as low as 0.25 W.L.S. Optional C02 sensor Optional acoustic plus kit Only 4.3 kg in weight Slimline dimensions of 480x480x195mm 3 x Variable fan speeds 2+1 Year parts warranty* Optional 2 or 3 speed switch Suitable for wall or floor mounting Optional Humidity or CO2 box sensor Optional Wired / RF wall controller Optional App / BMS control Optional commissioning App kit Optional 7x 125 to 90 radial adaptors Optional fault indicator Optional laptop connection for commissioning Demand Controlled Ventilation Historically, MEV-units used to run continuously: 24 hours a day, 7 days a week. At a single set speed This was deemed to be “ok” so the energy losses were deemed to be small. DUCO feels that this “old school”-way-of-thinking is a thing of the past and decided to go a step beyond the “normal” operation mode of a “traditional” MEV system. DUCO offers true “on demand” solutions which result in true energetically optimised ventilation solutions: To only ventilate, when necessary, where it is necessary and as long as it is necessary! The DucoBox Silent has an internal humidity sensor that detects high humidity and increases the performance until the set level is reached again It is also possible to install a CO2 box sensor inside the DucoBox Silent UK With an “on demand” DUCO-system, the occupant can always be assured to breathe the best possible indoor air, whilst also using the least amount of energy! DUCO brings you the SMARTEST ventilation solutions!   External Control Components The DucoBox Silent Connect can be linked with the following external control components.   Box Sensors Box sensors can be installed very easily and quickly and provide CO2 and/or moisture measurement in an air duct. They are wired directly to the circuit board. This means that no wiring for room sensors need to be provided. A DucoBox Silent contains a maximum of two box sensors – one CO2 Box sensor and/or one Humidity Box Sensor – each of which can be clicked separately into a specific duct opening or together into one duct opening of the DucoBox. Smart Demand User controller There are 3 types of User controllers are available in either wireless or wired versions and in black or white face plates Remote control (popular option) Remote Control with CO2 sensor Remote control with Humidity Sensor The wired version will require the additional 24v Power supply Duco Connectivity Board The Duco Connectivity Board enables the Duco Installation App to be used on your phone or tablet This PCB also enables interfacing for home automation and building management systems via REST API (locally or via the cloud) or Modbus TCP (locally). Both possible via Ethernet and Wi-Fi. CO2 Room Sensors The CO2 Room sensor is available in either wireless or wired versions and with black or white face plates Switch

GBP 420.31
1

Vent-Axia Lo-Carbon Heat Save

Vent-Axia Lo-Carbon Heat Save

Vent-Axia Lo-Carbon Heat Save Product Part Number Vent-Axia Lo-Carbon Heat Save - 496036 Vent-Axia Wired Zone Control Panel - 496037 Description Through-The-Wall Heat recovery Unit The Vent-Axia Lo-Carbon Heat Save is a ventilation unit designed for living rooms and bedrooms in single and multi-family buildings. The unit is usually located in an exterior wall to provide new air to the room. The Vent-Axia Lo-Carbon Heat Save uses a reversible fan to extract dirty air from the room and replace it with outside air 70 seconds later. This air passes through a filter to ensure that clean air enters the room. These systems work best in pairs as when one unit is extracting, the other can be supplying air to provide a balanced ventilation system. They are controlled by a SENWZP Sentinel wired zone controller which can operate up to 8 units in synchronization. This provides a single room or whole house balanced ventilation system with heat recovery. As well as filtering the air, the Vent-Axia Lo-Carbon Heat Save uses a thermal accumulator to extract warmth from the outgoing air and uses it to temper the incoming air to avoid the feeling of cold drafts and recover heat that would otherwise be lost to the outside. Typical Installation The Vent-Axia Lo-Carbon Heat Save can be fitted in a 180mm diameter hole. Maximum wall thickness is 460mm or 745mm with optional wall tube (see accessories). The wall sleeve length (included up to 460mm) can be cut down to size to fit any wall thickness. Vent-Axia Lo-Carbon Heat Save units work best in pairs. When one unit is extracting, the other can be supplying air to provide a balanced ventilation system. They alternate direction every 70 seconds when the thermal accumulator on the extract unit has warmed up allowing the supply air to benefit from these thermal gains. They are controlled by a SENWZP Sentinel wired zone controller. This is fully modular and controllable with customized ventilation profiles available so that every room in the home can have the perfect ventilation.

GBP 413.62
1

Vent Axia Lo-Carbon Solo Plus HT

Vent Axia Lo-Carbon Solo Plus HT

Vent Axia LO-CARBON SOLO PLUS HT Product Part Number Vent Axia Solo Plus HT - 427479 Description Long Life Ventilation The Lo-Carbon Solo Plus range from Vent-Axia has been specially designed for through the wall and ducted applications, suitable for internal bathrooms, toilets and other small rooms. Finished in white, the Lo-Carbon Solo Plus can be flush or surface mounted, with a 2 position 100mm circular spigot for rear entry or connecting to a vertical ducting system. The powerful centrifugal impeller allows installations using 100mm ducting in straight runs, whilst still achieving 15l/s as required by Building Regulations Approved Document F. Continuous running products, such as the Lo-Carbon Solo Plus, installed in all wet areas of a dwelling are classed as a wholehouse ventilation system and therefore only need to move the amount of air as outlined in table 5.1a and 5.1b of Building Regulations Approved Document F. The Lo-Carbon Solo Plus has an adjustable boost speed which is set at installation variable between a wall or duct setting for boost/override operation to meet Building Regulations thus ensuring minimum energy usage and low sound levels. All models have an optional speed for constant trickle ventilation (12l/s), selectable at installation. Depending on the model, the fan will switch from trickle (if selected) to boost via the pullcord/light switch/humidity sensor/PIR. All models can be wall, panel or ceiling mounted and can be connected to either circular, rectangular or Vent-Axia’s flat ducting. Enclosure of the electrical components is manufactured from flame retardant grade material.  

GBP 199.68
1

Nuaire DRI ECO LC PIV

Vent Axia Lo-Carbon Multivent MVDC-MS unit

Vent Axia Lo-Carbon Pozidry Compact Pro

Vent Axia Lo-Carbon Multivent MVDC-MS

Vent Axia Lo-Carbon Multivent MVDC-MS

Vent Axia Lo-Carbon Multivent MVDC-MS - VMSMEVPK The Multivent continuous mechanical extract ventilation range is designed for the simultaneous extraction of up to several bathrooms/ Wet Rooms to a centrally positioned unit normally installed in the attic space Complete DIY Kit of a Vent Axia MVDS-MS multiple room extraction unit with insulated Flexible Ducting and fittings suitable for extraction of 7 separate areas Our Comprehensive DIY Kits have everything you should require installing the system to building control regulations   Please note - You can purchase the MEV unit with or without the ductwork on this listing Key Features Vent Axia MVDC-MS multi room extraction unit Any products not required can be returned for full refund (excluding return delivery cost) Any extra products required will be discounted to the Kit Price (excluding delivery) Variable speed settings Ultra-quiet - acoustically lined for low noise levels Complies with Building ADF (System 3) Option of wall, ceiling, and loft mounting Improved controllability The unit has Long life, low energy multispeed DC motor PVC outer casing with an acoustic lining is included as standard, ensuring minimum noise levels With a DC motor the Multispeed Multivent is one of the most efficient central extract units in the UK. The Multivent MVDC MS offers the option of ‘Close Control’ both in the residential and the commercial sectors.  Technical Features Max Airflow of 350m3/h Best in class Specific Fan Power (SFP) as low as 0.15 wls Dimensions (H x W x D) 310mm x 360mm x 249mm Fitted with four extract 125 or 100mm diameter spigots allowing quick connection to ducts Recognised in SAP Appendix Q Switched Live Boost connection Fully variable normal and boost speeds Fully serviceable unit with all parts accessible 2-year standard or optional 5-year parts warranty  Controllability The potentiometer-controlled speed selector allows accurate setting of airflow The unit has 2 fully variable speeds for trickle and boost, with an inbuilt humidistat activation for the boost speed. A switched live

GBP 288.00
1

Airflow Adroit Digital Controller

Airflow Adroit Digital Controller

Airflow Adroit Digital Controller Product Part Number Adriot Digital Controller - 90000610 Description Adroit Digital Controller Wall mounted, LCD display with four 100% independently user adjustable air flow profiles (Home, Away, Boost, Fireplace). A range of indoor parameters ie: air flow rates, temperature, humidity, by-pass, time clock settings, CO2 sensor, filter alert are adjustable to suit your indoor environment. Internet connectivity via Adroit ‘Cloud’ for control at home or on the go. Airflow Adroit ventilation units make controlling your indoor ventilation so easy. Simply adjust your Adroit using 4 different profiles: Home, Away, Boost or Fireplace. Just choose the suitable one! Not only can your ventilation be controlled with the controller, but also via the Adroit Cloud service. The service gives you the potential to manage the ventilation of your home remotely over the internet, for example with your smartphone. The intelligent, interactive Adroit ventilation unit can also be connected to your home automation system and the home network. Adroit units have an integrated humidity sensor that monitors the humidity level of your home and automatically adjusts the ventilation to the optimal level and ensures that you always enjoy high quality indoor air. The efficient energy recovery doesn’t waste the heat of the outgoing exhaust air, but uses it to warm the fresh air being supplied from outdoors. Adroit’s energy efficiency is further improved by boosting or reducing its ventilation, either manually or automatically, through sensors based on your current need. The Adroit even reminds you when the filters need to be changed – as easy as it can be! INTELLIGENT PROFILE CONTROL The Adroit’s control panel is easy to use, with intuitive icons anda coloured display. The elegant control panel makes it easy toadjust your ventilation. Profile-based control also saves you energy. The handy week clock allows you to program the ventilation profiles around your personal routine. You can, for example, set the ventilation to Boost from optional room switches or automatically from optional CO2 or humidity sensors. Fireplace ensures safe ventilation in rooms whilst carbon fuel fires are in use. Proper, energy efficient ventilation is only a click away.  

GBP 316.22
1

Vent Axia Pozidry Pro

Vent Axia Pozidry Pro

Vent Axia Pozidry Pro Product Part Number Vent Axia Pozidry Pro - 476310 All the Technical Things Selectable air capacities to suit floor areas up to 200m2 IPX2 rated Uses the latest lo-carbon motor technical for low running costs Ultra-low sound level Complete with ceiling diffuser, flexible duct, and worm drive clips Anti-vibration legs offer flexibility when fitting and guarantee silent running Flexible feet allow the unit to be installed across two joists or along a joist offering simple, easy installation Moulded handle makes carrying the unit safe and simple, allows you to change the pitch of the PIV if hanging kit is used Pozidry Pro is unique in offer F7 filters which filter down PM2.5 including diesel particulates Smart Sense technology is easy to set up with smart data logging capabilities all access via the intuitive 3 button menu This unit uses a sensor to monitor the temperature in the loft The Lo-Carbon PoziDry Pro features a specially developed Lo-Carbon DC fan/motor arrangement which runs quietly and delivers incredibly low running costs of less than £3 per year to run, the motor operating temperature is -25/40°c Performance The Lo-Carbon PoziDry pro uses a sensor to monitor the temperature in the loft, automatically adjusting the air volume when necessary. The unit will continuously ventilate silently in the background whilst in ‘Trickle’ mode. Once the unit automatically senses excess heat being lost into the loft the airflow will increase to ‘Normal’ mode to recover heat that would otherwise be lost through the roof. During summer months should the loft exceed 27°C the unit will enter ‘stand-by’ mode in order stop the circulation of warm air allowing for a more comfortable living environment. PoziDry Pro Heater models automatically turn on the 500W heater to boost air temperature by 10°C during colder months. Under assessment with BBA. Controllability The unit can be controlled by Smart Sense™ Technology – Easy set up and smart data logging capabilities all accessed via the intuitive 3 button menu on the unit Speed control selection is easy. Once house size is selected based on number of bedrooms, PoziDry Pro automatically selects the correct Trickle and Normal speeds. Should you need to adjust speed manually this can be done easily. Data Logger allows the unit to record how long it has been running in each of its speeds. It also measures the number of days the product has been switched on to provide precise running information. Smart Sense technology can also record the duration of heater activity and energy used Installation The Lo-Carbon PoziDry Pro is uniquely flexible in its

GBP 342.00
1