25 results (0,15750 seconds)

Show all filters

Brand

Show all

Merchant

Price (EUR)

Reset filter

Products
From
Shops

Bullnose Fascia Large End Cap - 300mm x 25mm White

Bullnose Fascia Large End Cap - 300mm x 25mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This end cap is 313mm long overall, with a 300mm useable length (one curved edge).Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 2.54
1

Bullnose Fascia End Cap Pair - 100mm x 25mm White

Bullnose Fascia End Cap Pair - 100mm x 25mm White

Our Bullnose fascia is manufactured by Freefom, it is 18mm thick and it comes in a range of widths from 150mm to 250mm.This end cap is 100mm long overall, consisting of a pair of end caps.Bullnose fascia boards can be fixed directly to the rafter ends without the need for a backing board, itandnbsp;should be fixed using 2 x 65mm polytop nails at each rafter (maximum spacing 600mm).The rear of the board is rebated at the bottom edge to accept a soffit board.andnbsp;

GBP 1.34
1

White Fascia Capping Board Internal Corner - 300mm

White Fascia Capping Board Internal Corner - 300mm

Internal corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. Internal corners are usually found at the foot of a valley on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Internal corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 3.54
1

Ogee Fascia Corner - 300mm White

Ogee Fascia Corner - 300mm White

Corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint. Fascia corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 3.98
1

White Fascia Capping Board Double End Corner - 500mm x 42mm

White Fascia Capping Board Double End Corner - 500mm x 42mm

Corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 2.37
1

White Fascia Capping Board External Corner - 300mm

White Fascia Capping Board External Corner - 300mm

Corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 2.66
1

FloPlast Shiplap Cladding Butt Joint - 150mm White

FloPlast Shiplap Cladding Butt Joint - 150mm White

The 150mm UPVC Shiplap Cladding Butt Joint Trim is to be used to join boards together and when used, breaks up the line a little bit on larger installations covering the joint in a staggered effect.The butt joint is usually used as an alternative to a centre joint trim which produces a straight line joint.The Shiplap Cladding Butt joint is available in White, Anthracite Grey, Black Ash, Golden Oak or Rosewood and is to be used with the 150mm Shiplap Cladding boards.For more information on cladding joints please take a look at our short video:

GBP 1.42
1

Fascia Double End Corner Trim - 500mm x 35mm White

Fascia Double End Corner Trim - 500mm x 35mm White

Corner trims are used to hide the 10mm expansion gap that should be left between two fascia boards at the corner of the eaves.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.Double ended corners can be cut to size with a standard hacksaw or fine toothed saw.

GBP 2.84
1

White Fascia Capping Board External Corner Joint Trim - 135 Degree x 300mm

White Fascia Capping Board External Corner Joint Trim - 135 Degree x 300mm

135 Degree corner trims are used to hide the 10mm expansion gap that should be left between two boards at the corner of the eaves. 135 degree corners (or 45 degree corners as they are also called) are usually found above a bay window on a roof.To enable the system to expand and contract correctly in a different range of temperatures, one side of any joint or corner on any PVC fascia installation should be glued to the board and the other side should be sealed with low modulus silicon, which allows movement within the joint.All corner trims can be cut to size with a standard hacksaw or fine toothed saw

GBP 3.73
1

Tapco Composite Slate Roof Tile - 305mm x 445mm Grey

Tapco Composite Slate Roof Tile - 305mm x 445mm Grey

TapcoSlate Classic roofing is a ultimate solution to tile roofing on domestic and commercial properties. Each individual tile features pre-marked screw andamp; fixings guides as well as horizontal spacers (5mm each side, making 305mm overall) on each side of the tile to inform the installer how close the tiles should be placed next to each other. These features make the installation process even easier and faster.If needed, these tiles, as well as the ridges can be cut with a fine-toothed handsaw or a jigsaw. A fully installed composite roofing system is impermeable; it is BBA approved, has a BROOF(t4) designation, EN15601 wind rated (at 12 and 14 degrees) and has a Class IV hail rating, making it a great alternative to traditional slate, while being easier to handle and install.Click here to view our full installation guide for composite slate roofing tiles.Roof PitchGaugeTiles Per Square Metre12 to 25 degreesandnbsp;152mm2225 to 27.5 degrees165mm2027.5 to 30 degrees178mm1930 to 70 degrees191mm18andnbsp;

GBP 3.46
1